Spectrum Industries 37310 User manual

1. Attach leg mechanisms
1. Place worksurface face-down onto a non-abrasive surface.
2. Orient the leg mechanisms and release handle as shown and
align with the worksurface mounting holes. Figure 1A.
3. Attach the leg mechanisms and release handle to the worksurface
using (20) #14 x 7/8” PHSM screws and tighten securely.
4. Secure the cables to the worksurface with the included clips, (4)
#8 x 3/4” PHSM screws, and pre-drilled holes. Figure 1B.
(20) 0101382
#14 x 7/8” PHSM screws
0108517R3 Page 1 of 3
Assembly Instructions
Important
Before you begin, please make sure all parts and proper quantities
are included. Any parts damaged during shipment must be reported
within 15 days of receipt. To report information regarding damage, to
purchase parts or accessories, or if you have any questions, please
contact us at:
www.spectrumfurniture.com
715-723-6750, 800-235-1262
Thank you for purchasing Spectrum products!
Phillips
Screwdriver
Tools Required
24”D
37310 - 48”W
37312 - 60”W
37314 - 72”W
30”D
37311 - 48”W
37313 - 60”W
37315 - 72”W
Flex Flip Tables
Hex wrench
(included
with legs)
1/2” wrench
Figure 1A
attach leg mechanisms
to worksurface with
#14 x 7/8” PHSM screws
cables leg mechanism
worksurface
Figure 1B
secure cables with (4) PHSM
screws & cable clips
(included with table legs)
cable
cable clip
release
handle

2. Attach legs
0108517R3 Page 2 of 3
1. Set a leg on each leg mechanism. Figure 2.
2. Attach each leg with the included hex screws (4 per leg) and hex wrench.
3. Tighten screws securely.
4. Be sure swivel wheels are tightened securely. (Tighten with 1/2” wrench if necessary.)
5. Carefully tip the table upright- this will require two people.
Figure 2Figure 3A
Figure 3CFigure 3B
3. Table operation
• To adjust the worksurface height, press the spring clip button on one leg and raise or lower the worksurface and upper leg assembly (slightly twisting then sliding
the leg after the button has been pressed will help keep it retracted until its aligned with the new hole.) Figure 3A. Align the spring clip button with one of the
adjustment holes to lock the leg into the new position. Repeat this procedure on the other leg while making sure to use the same hole position on both legs.
• To ip-up the worksurface, pull the release lever while lifting up the edge of the worksurface until it locks into place. Figure 3B. To lower, pull the release
lever while lowering the worksurface-be sure it locks into place. Multiple tables can be “nested” together next to a wall to save space. Figure 3C.
Spring clip button on
each leg provides 9” of
total height adjustment
in 1” increments
leg mechanism
hex screws
(included with
legs-4 required)
leg
leg leg
mechanism

0108517R3 Page 3 of 3
925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 800-235-1262, 715-723-6750 Fax: [phone]
E-mail: [email protected] web: www.spectrumfurniture.com
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products is manufactured from the best materials available and each
product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table
below from the date of delivery. This warranty shall not apply to defects or damage resulting from misuse, abuse, neglect, improper care, modication
or repair not authorized by Spectrum, or any other cause outside the control of Spectrum. Spectrum will, at its sole option, either repair or replace the
defective product.
This warranty is exclusive; no other warranty, written or oral, is expressed or implied. This warranty is given by Spectrum to Buyer and to no other per-
son or legal entity. No Spectrum dealer, distributor, agent or employee is authorized to make any modication or addition to this warranty.
NOTWITHSTANDING ANYTHING TO THE CONTRARY, SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR
LIQUIDATED DAMAGES, INCLUDING CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES. IN NO EVENT SHALL SPECTRUM’S LIABIL-
ITY, WHETHER UNDER CONTRACT OR WARRANTY, IN TORT OR OTHERWISE, EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM
FOR THE PRODUCT AT ISSUE AND “RECALL ACTION” EXPENSES. SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS
OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABIL-
ITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM, OR ANY UNDERTAK-
INGS, ACTS OR OMISSIONS RELATING THERETO.
Our Customer Service Department is ready to provide immediate attention to any questions, comments or concerns. They are available to answer your calls
Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome via e-mail at: [email protected].
Warranty Table
Item Warranty Period
• Adjustable Crank/Electric Desk Legs • 1 Year
• Flat Panel Desk Gas Cylinders
• Adjustable Height Chair Parts – including frames,
gas cylinders, wood and plastic parts, and control
handles Adjustable Height Chair Parts Casters
• Adjustable Height Chair Upholstery
• In-Stock Upholstery
• Graded-In Fabrics and Customer Owned Material
• 7 Years
• 2 Years
• 2 Years
• No Warranty
• Height Adjustable Columns and Lifts
• 1 Year
• General Use Casters
• Electrical
• Keyboard/Mouse Trays
• Flat Panel Monitor Arm – General Parts
• Flat Panel Monitor Arm – Gas Cylinders
• 5 Years
• 2 Years
• Computer Desk Chassis
• Cart Chassis
• Lectern Chassis
• 10 Years
Warranty