Spectrum Industries 37386 User manual

PART# QTY ITEM
021538 8 #8 x 1/2” PHTS
0160915 2
Styrene angle
w/ adhesive
1.25” x 1.25” x 4”
0192395 2 3/4” x 3/4” Cable holder
058423 6 5-1/2” Cable tie
0192178 1 6” Driver adapter
0192179 1 12 volt power supply
0192180 1 12” RGB F to M
cable link
0192181 1 Plus shape connector
0192182 1 LED Controller
and RF Remote
0192183 2 72” Interconnection
cable
0192272 2 6” Interconnection cable
0192265 4 4” RGB LED Tape light
Assembly InstructionsAssembly Instructions
0192437 Page 1 of 4
Assembly InstructionsAssembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
LED Lighting Kit for ShoutcasterLED Lighting Kit for Shoutcaster
3738637386
1. Remove accent / side panels (if installed)
Backer
panel
4mm
Backer
panel
Accent / side panel
Accent / side panel
1. Remove the accent / side panels by removing
the 4mm JC bolts inside unit.

Accent
panel
Brace
Styrene backer
Slot
0192437 Page 2 of 4
1. Attach the adhesive styrene angle behind the accent panel in the
center.
4. Attach styrene angle inside accent panel
2. Secure backer panel with screws
1. Position backer panel tight to worksurface.
2. Install (4) #8 x 1/2” PHTS screws at the locations
shown to secure the backer.
3. Repeat on other backer panel.
#8 x 1/2” PHTS
(4 required)
9.375 .5
2.5
9.375 .5
2.5
.5
Existing hole
Existing hole
Backer panel on
audience-side
Styrene
angle
Accent
panel
3. Remove brace securing styrene backer
X2 X2
X2

2
0192437 Page 3 of 4
1. Attach (2) 4” LED tape strips to the each side of the styrene
angle with LED bulbs pointing up and down.
2. Connect the tape strips with a 6” interconnection cable.
5. Attach LED tape to styrene angle
4” LED
tape light
6” interconnect
cable
Styrene angle
1. Connect the LED components as shown and make sure
all 4 tape strips light up.
6. Connect LED components
4” LED tape 4” LED tape
72” interconnection cable
Plus
connector
6” Driver
adapter
12” RGB
F-to-M link
LED
Controller
72” interconnection cable
12V Power supply
(connect to power
strip or wall outlet)
Assembly tip: If the LED tape lights do not light up, check polarity
of connectors. They may need to be rotated 180-degrees and
re-plugged in.
4” LED tape 4” LED tape
X2
6” interconnection
cable
6” interconnection
cable

0192437 Page 4 of 4
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2020 Spectrum Industries Inc., All rights reserved.
1. Place the plus connection, LED controller, and 12V power supply in
the cord channel.
2. Route each 72” interconnection cable around to the backer panel
and plug into the LED tape. (Use one cable holder on each side to
support and route the wire).
7. Route wires
8. Replace accent / side panels
Accent / side panel
Accent / side panel