Spectrum Industries 55260TW User manual

LH cut-out RH cut-out
55345 55346
Media Director V2 Lectern
Standard Media Director V2
w/ TouchLink™ Cubby Panel 350CV cut-out in work surface
(no overbridge)
w/ blank overbridge (OB-3)
w/ MediaLink™ MLC 226 IP AAP cut-out in overbridge (ES-3)
w/ TouchLink™ 700MV cut-out in overbridge
55294
55234
55347
55260
Media Director V2 Lectern
55260TW
Media Director V2 Lectern w/ toe kick
55260TK
Media Director V2 Lectern w/ RH
TouchLink™ Cubby Panel 350CV cut-
out in work surface
Owner's Manual
0103148XR6 Page 1 of 9
Media Director V2 Lectern w/ TouchLink™
700MV cut-out in overbridge
55347TW
Media Director V2 Lectern
55260TW
Media Director V2 Lectern w/ toe kick
55260TK
Media Director V2 Lectern w/ toe
kick & blank overbridge (OB-3)
55294TK
Media Director V2 Lectern w/ MediaLink™
MLC 226 IP AAP cut-out in overbridge &
arched toe kick (ES-3)
55234TK
Media Director V2 Lectern w/ RH
TouchLink™ Cubby Panel 350CV cut-
out in work surface
55346TW
Owner's Manual
IMPORTANT:
Before you begin, please make sure all parts and proper quantities are
included. Any parts damaged during shipment must be reported within 15
days of receipt. To report information regarding damages or if you have any
questions, please call 1-800-235-1262.
CAUTION:
Before using this product, read this manual and follow all safety and
operating instructions.
Spectrum Industries, Inc.
Chippewa Falls, WI 54729, USA
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!
0103148XR6
P
age
1
o
f
9

A. To remove door, pull down the quick-release lever as shown in Figure 1A while removing the door.
B. To re-attach the door, pull down the quick-release lever while inserting the door hinge pins into the pin holes. Figure 1.
Release the lever when the upper hinge pin is aligned with the upper hinge pin hole-this will secure the door.
Quick-Release Door Hinge Operation
Quick-Release
Lever
Doo
r
Upper Hinge
Pin Hole
Hinge Pin
Figure 1A
●Read this owners manual before assembly or operation
Safety Assembly / Setup
Phillips Head
Screwdriver
Tools Required:
Figure 1B
Acorn Nut
To raise
handle-side
of door
To lower
handle-side
of door
Bottom of Door
0103148XR6 Page 2 of 9
A. To remove door, pull down the quick-release lever as shown in Figure 1A while removing the door.
B. To re-attach the door, pull down the quick-release lever while inserting the door hinge pins into the pin holes. Figure 1.
Release the lever when the upper hinge pin is aligned with the upper hinge pin hole-this will secure the door.
Quick-Release Door Hinge Operation
A. To move the rack rails to a different mounting position, remove the 1/4-20 x 5/8" PHM screws
and re-attach in the new position as shown in Figure 2.
Changing Rack-Rail Position
Figure 1
Quick-Release
Lever
Doo
r
Hinge Pin
Lower Hinge
Pin Hole
Upper Hinge
Pin Hole
Hinge Pin
Figure 1A
Figure 2
Rear Rail Position
Front Rail Position
1/4-20 x 5/8"
PHM screws
Read this owners manual before assembly or operation
Safety Assembly / Setup
Phillips Head
Screwdriver
Tools Required:
Note:If the door appears to be misaligned, a slight adjustment can
be made to the bottom hinge-side of the door. Figure 1B.
1. Using the quick-release lever, remove the door.
2. Slightly loosen the acorn nut on the bottom corner of the door
with a 3/8" or adjustable wrench and Phillips screwdriver.
3. Reposition the acorn nut and screw as required (repositioning
the acorn nut toward the rear of the door will lift the handle-
side of the door upward.)
4. After adjustment, be sure the nut is tightened securely. Re-
attach door and check alignment. Repeat this procedure if
necessary.
Figure 1B
Acorn Nut
To raise
handle-side
of door
To lower
handle-side
of door
Bottom of Door

A. To access the upper keyboard / rack rail area from the back, remove the (4) JC bolts and remove the back panel. Figure 3.
B. Replace the panel and tighten the JC bolts securely.
Back Panel Removal
JC bolt
Back Panel
Figure 3
Figure 4
Toe Kick
Lectern
Note: (4) fasteners are req'd to anchor toe-kick to floor.
1/4-20 x 35mm JC bolts
(4) req'd
0103148XR6 Page 3 of 9
A. To access the upper keyboard / rack rail area from the back, remove the (4) JC bolts and remove the back panel. Figure 3.
B. Replace the panel and tighten the JC bolts securely.
Back Panel Removal
JC bolt
Back Panel
Figure 3
Figure 4
Toe Kick
Lectern
Note: (4) fasteners are req'd to anchor toe-kick to floor.
1/4-20 x 35mm JC bolts
(4) req'd
Floor Anchoring (Toe Kick models only)
A. If your Media Director is equipped with a toe-kick, and you wish to attach it to the floor, the toe-kick will need to be detached from the
lectern. To detach, remove the (4) 1/4-20 x 35mm JC bolts (one on each corner) from inside the lectern.
B. Carefully lift the lectern off the toe-kick. This will require several people. Figure 4.
C. Locate the toe-kick into the final position on the floor and mark the (4) mounting hole locations on the floor.
D. Drill holes into the floor and anchor the toe-kick with appropriate fasteners. (The toe-kick mounting holes are approximately 1/2" dia.)
E. Carefully lift the lectern back onto the toe-kick and align the (4) mounting holes.
F. Re-attach the lectern to the toe-kick with the previously removed JC bolts.
Attaching Optional Keyboard Tray
A. Hook the keyboard slide/track into one of the pre-installed clips under the left or right-side of the work surface. Figure 5.
B. Attach slide/track to the work surface using (2) screws (from the keyboard tray kit) and the pre-drilled work surface holes.
C. Slide the keyboard tray into the slide/track.
D. Refer to the keyboard tray instructions for remainder of installation.
Figure 5
screws
right slide/track clip
left slide/track clip
slide/track
0103148XR6
Page
3
of
9

Technical Specs
Capacity
●Overall dimensions: (See dimensioned drawings)
●Total upper internal area: 395/8"W x 273/4"D x 63/8"H
●Total lower internal area: 395/8"W x 271/4"D x 2415/16"H
●Adjustable-height document camera/task shelf is 23"W x 273/4"D
●The 3" swivel twin-wheel locking casters have a weight capacity of
165 lbs each (660 lbs max total unit weight)
●Optional 15' retractable 15-amp cord reel
●Four sets of standard rack rail provide 13RU each (front and rear
mounted) (Total of 52RU)
●Meets or exceeds all ANSI-BIFMA test standards
●Features and specifications subject to change without notice
●Unit weights (nominal):
55260TW - 260 lbs (w/ casters)
55260TK - 263 lbs (w/ toe kick)
●Shipping weights (nominal):
55260TW - 316 lbs (w/ casters)
55260TK - 319 lbs (w/ toe kick)
Construction
●The work surface and base panel are constructed from 11/16" thick industrial-grade composite board with
.030 high-pressure laminate on one face, and a balancing phenolic backer on the opposing face
●Metal components consist of 16-gauge steel and 20-gauge steel
●16-gauge steel doors and corner columns
●Work surface edges are covered with 3mm vinyl
●All metal components are finished with a scratch-resistant powder coat epoxy
●Solid wood corner trim
●Each Media Director V2 Lectern is factory-assembled w/ casters, packaged, and shipped on its own skid
55260TW
Media Director Lectern V2 w/ casters
(shown with optional handle, flip-up document camera/task
shelf, pull-out drawer, and adjustable keyboard tray)
0103148XR6 Page 4 of 9
Technical Specs
Capacity
Overall dimensions: (See dimensioned drawings)
Total upper internal area: 395/8"W x 273/4"D x 63/8"H
Total lower internal area: 395/8"W x 271/4"D x 2415/16"H
Adjustable-height document camera/task shelf is 23"W x 273/4"D
The 3" swivel twin-wheel locking casters have a weight capacity of
165 lbs each (660 lbs max total unit weight)
Optional 15' retractable 15-amp cord reel
Four sets of standard rack rail provide 13RU each (front and rear
mounted) (Total of 52RU)
Meets or exceeds all ANSI-BIFMA test standards
Features and specifications subject to change without notice
Unit weights (nominal):
55260TW - 260 lbs (w/ casters)
55260TK - 263 lbs (w/ toe kick)
Shipping weights (nominal):
55260TW - 316 lbs (w/ casters)
55260TK - 319 lbs (w/ toe kick)
Construction
The work surface and base panel are constructed from 11/16" thick industrial-grade composite board with
.030 high-pressure laminate on one face, and a balancing phenolic backer on the opposing face
Metal components consist of 16-gauge steel and 20-gauge steel
16-gauge steel doors and corner columns
Work surface edges are covered with 3mm vinyl
All metal components are finished with a scratch-resistant powder coat epoxy
Solid wood corner trim
Each Media Director V2 Lectern is factory-assembled w/ casters, packaged, and shipped on its own skid
Top View
55260TW
Media Director Lectern V2 w/ casters
(shown with optional handle, flip-up document camera/task
shelf, pull-out drawer, and adjustable keyboard tray)
Note: Optional keyboard tray can be mounted
in a left or right position under the work surface.
Left-Side View Instructor's View
Optional 3-position
adjustable-height document
camera/task shelf
Optional adjustable
keyboard tray
Optional pull-out
drawer
0103148XR6
Page
4
of
9

3" Twin-Wheel caster
(TW)
55234TW
ES-3 Media Director V2 Lectern w/ Twin-Wheel casters
(shown with optional handle, flip-up document camera/task shelf, pull-out
drawer, and adjustable keyboard tray)
0103148XR6 Page 5 of 9
Media Director Rack Rail
(13 Rack-Units available)
3" Twin-Wheel caster
(TW)
Top View
55234TW
ES-3 Media Director V2 Lectern w/ Twin-Wheel casters
(shown with optional handle, flip-up document camera/task shelf, pull-out
drawer, and adjustable keyboard tray)
Left
-
Side View Instructor's View
Optional 3-position
adjustable-height document
camera/task shelf
Optional adjustable
keyboard tray
Optional pull-out
drawer
0103148XR6
Page
5
of
9