Spectrum Industries 68204 User manual

0108810R3 Page 1 of 2
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Flip-up shelf for equipment rack
68204
(4) 021587
8-32 x 1/2” PHMS
(8) 026073
#8 x 3/4” PHSM
(4) 052605
1/4-20 x 15mm
JC bolts
Phillips
Screwdriver
Tools Required
Note: For stability reasons, Spectrum does not recommend attaching the
shelf to a stand-alone equipment rack. Do not exceed 35 lbs of weight
on shelf. Not compatible with end-support legs.
(1) 039622
2” Round
grommet
(2) 059984
Snap-in
grommet
(1) 025039
4mm Hex wrench 4mm Hex
Wrench
(included)
(2) 056886
Folding bracket
(1) 0108808
Shelf support
(1) 0108807
Shelf
Equipment rack
1. Attach shelf support to equipment rack
Folding
bracket
8-32 x 1/2” PHMS
(2 per bracket)
Shelf support
1/4-20 x 15mm
JC bolts
Snap-in
grommet
Figure 1
1. Align and attach the shelf support to the side of the equipment rack
with (4) 1/4-20 x 15mm JC bolts and tighten securely. Figure 1.
Note: If installing shelf onto a Freedom One eLift equipment
rack, install the (2) 1/4” washers as shown.
2. Install the two snap-in grommets into the shelf support.
(2) 026059
1/4” Flat washer
Used on Freedom One®
equipment racks only
Freedom One®
equipment racks only:
Install (2) 1/4” washers
here on instructor-side
Instructor-side
2. Attach folding brackets to shelf support
1. Extend and lock the folding shelf brackets
into the horizontal position.
2. Align and attach each folding bracket to
the shelf support with (2) 8-32 x 1/2” PHM
screws. Do not tighten these screws
completely yet.

2” Grommet
0108810R3 Page 2 of 2
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
3. Attach shelf to folding brackets
1. Attach the shelf to the fully-extended folding brackets with
(8) #8 x 3/4” PHSM screws. (4 per bracket). Figure 2.
2. Tighten all screws securely.
3. Install 2” shelf grommet.
Figure 2
Folding
bracket
Shelf
4. Shelf operation
To lower or ip-up the shelf, release the levers under each folding bracket at
the same time while slowly lowering or raising the shelf. The shelf will lock
into place when lifted into the horizontal position.
#8 x 3/4” PHSM
(4 per bracket)
CAUTION
Keep clear of pinch points during shelf movement.
Do not exceed 35 lb [15.9 kg] of weight on shelf.
Operation
The shelf will automatically lock into place when lifted into the
horizontal position with the levers released. To lower or ip-up the
shelf, press and hold the levers under each folding shelf bracket at the
same time while slowly lowering or raising the shelf. Do not exceed a
maximum of 35 lb of weight on the shelf. Do not move the unit while
the shelf is in the horizontal position.
Note: Power and communication wiring for document cameras, laptop
computers, and / or projectors placed on the ip-up shelf should be routed
on top of the audience-side of the shelf. Use of the shelf grommet hole for
wiring will result in pinching of the cords when the shelf is lowered.
CAUTION
Keep clear of pinch points during shelf movement.
Do not exceed 35 lb [15.9 kg] of weight on shelf.
Figure 3
Folding shelf
bracket
Release lever
(press here)