Spectrum Industries 55410TW User manual

0111252 Page 1 of 4
Assembly Instructions
Assembly Instructions
Before you begin, please make sure all parts and proper quanti-
ties are included. Any parts damaged during shipment must be
reported within 15 days of receipt. To report information regarding
damages or if you have any questions, please call 1-800-235-1262.
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for purchasing Spectrum products!
Tools Required
Assembly Instructions
Assembly Instructions
Inspiration Lectern Side Table
Inspiration Lectern Side Table
Phillips Screwdriver
(3) 052901
8-32 x 3/8”
PHMS
#55410TW - w/ casters (mobile lectern)
#55410TW - w/ casters (mobile lectern)
#55409TK - w/ glides (toe kick lectern)
#55409TK - w/ glides (toe kick lectern)
55410TW
55409TK
(17) 026064
1/4-20 x 5/8”
PHMS
(4) 026073
#8 x 3/4” PHSM
screw
(2) 0105662
5/16-18 Stem
Caster
#55410TW Inspiration Lectern Side Table
#55410TW Inspiration Lectern Side Table
Parts Bag
Parts Bag
(3) 052901
8-32 x 3/8”
PHMS
(17) 026064
1/4-20 x 5/8”
PHMS
(2) 037779
5/16-18 x 1
Glide
#55409TK Inspiration Lectern Side Table
#55409TK Inspiration Lectern Side Table
Parts Bag
Parts Bag
(1) 0111445
Worksurface
(1) 0111446
Modesty Panel
(1) 0111447
Leg
(1) 0111450
Backer Plate
(1) 0111472
Leg
(1) 0111449
Unit-to-Unit Bracket
(1) 025069
Caster/Glide
Wrench
(4) 026073
#8 x 3/4” PHSM
screw
(1) 025069
Caster/Glide
Wrench

0111252 Page 2 of 4
Backer
Plate
Lectern Side
Panel
Figure 1
1. Attach Unit-to-Unit Bracket to Lectern
1. Attach Unit-to-Unit Bracket to Lectern
A. The table is symmetrical and can be mounted on either side of the lectern. Determine
which side the table will be mounted.
B. Attach the unit-to-unit bracket and the backer plate to the left or right side panel with (3)
1/4-20 x 5/8” PHM screws. Figure 1. The backer plate will be inside the lectern. Do not
tighten the screws completely-they will be tightened after the table is connected.
1/4-20 x 5/8”
PHM screws
(3 req’d)
Unit-to-Unit
Bracket

0111252 Page 3 of 4
A. Place the worksurface face down onto a non-abrasive surface.
B. Attach the leg as shown with (8) 1/4-20 x 5/8” PHM screws. Figure 2A. Tighten securely.
C. Attach the (2) casters (or glides for 55409) to the bottom of the leg and tighten securely.
D. Attach the modesty panel to the worksurface with (4) #8 x 3/4” PHSM screws. Figure 2A shows a right-hand table installation.
Note: Figure 2 shows a right-side table assembly. If as-
sembling a left-side table, the modesty panel can be flipped
and attached to the opposite side of the worksurface using
the other set of predrilled holes.
Figure 2A
Figure 2B
Modesty
Panel
Worksurface
E. Attach the modesty panel to the leg with (3) 1/4-20 x 5/8”
PHM screws. Figure 2B.
2. Assemble Table
2. Assemble Table
Leg
1/4-20 x 5/8”
PHM screws
(8 req’d)
(2) Casters or
(2) Glides
When assembling a left side
table, use this set of 4 holes to
attach the modesty panel
Modesty
Panel
1/4-20 x 5/8”
PHM screws
(3 req’d)
#8 x 3/4”
PHSM screws
(4 req’d)
Modesty Panel
flush w/ work-
surface edge
Note: The fastener slots in the mod-
esty panel allow slight adjustment
with the worksurface. The modesty
panel should be attached flush with
the edge of the worksurface.

0111252 Page 4 of 4
925 FirstAvenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 1-800-235-1262 Fax: [phone]
E-mail: [email protected] web: www.spectrumfurniture.com
A. If your Inspiration lectern is the mobile version, lock all four casters.
B. Set the edge of the assembled table onto the previously installed unit-to-unit bracket. Figure 3A.
C. Align the bracket and worksurface mounting holes and attach with (3) 1/4-20 x 5/8” PHM screws (finger-tight only).
D. Align the modesty panel and lectern side panel mounting holes and attach with (3) 8-32 x 3/8” PHM screws.
E. Make sure the table is level side-to-side, and front-to-back, then tighten all screws securely-including the unit-to-unit bracket screws.
3. Attach Table to Lectern
3. Attach Table to Lectern
Figure 3A
Figure 3B
Modesty
Panel
Worksurface
1/4-20 x 5/8”
PHM screws
(3 req’d)
#8-32 x 3/8”
PHM screws
(3 req’d)
Lectern Side
Panel
Unit-to-unit Bracket
w/ slots
Note: The side table with casters is only designed for
short distance mobility and repositioning within a room.
Frequently moving the unit long distances or over uneven
thresholds is not recommended. Do not lift up or pull the
table-move the table and lectern together.
Assembled
Table
Note: The table worksurface should
be parallel with the lectern worksur-
face. The Unit-to-unit bracket has
slots that allow slight vertical adjust-
ment with the fasteners that attach it
to the side of the lectern. If adjust-
ment is necessary, loosen the fasten-
ers attaching the table to the lectern,
reposition the unit-to-unit bracket and
table, then retighten.