Spectrum Industries Touchboards 95501 User manual

Keyboard Tray
#95501, #95506
Assembly Instructions:
Tools Required:
Phillips Screwdriver
Before you begin, please make sure all parts and proper quantities are
included. Any parts damaged during shipment must be reported within
15 days of receipt. To report information regarding damages or if you
have any questions, please call 1-800-235-1262.
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!
(1) 044480
Spacer Block
(1) 044321
Parts Bag 2 includes the following:
(1) 040857
"Z" Bracket
for 95501 only
(1) 044217
"Micro-Arm" Bracket
for 95506
(8) 026070
#8 x 1-3/4" PHSM (5) 043878 Plastic Spacer
(1) 042342
17-3/4" Slide
95501
95506
(8) #8 x 5/8" PHSM screw
(1)
Rbb B
Attaching the "Z" or "Micro-Arm" Bracket to Keyboard Tray
1.
A. Align the "Z" or "Micro-Arm" Bracket with the 6 pre-drilled holes in the center of the keyboard tray. Figure 1.
B. Using (6) #8 x 5/8" PHSM screws, attach the bracket to the keyboard tray and tighten securely.
Figure 1
Slide
(1)
R
u
bb
er
B
umpe
r
(1) Slide guard
Rubber Bumper
Underside of
worksurface
Attach 1" from edge
Figure 2
"Z" Bracket shown
Keyboard Tray
(6) #8 x 5/8" PHSM Screws
Attaching the Keyboard Tray to Desk
2.
Note: Some desk products will have a metal support bar underneath the worksurface. If this is the case, go to steps 4 & 5.
A. Flip the worksurface /desk upside-down onto a non-abrasive surface.
B. Locate the slide perpendicular and about 1" from the front edge of the worksurface. The slide should not be mounted
closer than 8" to the nearest leg.
C. Attach the slide using (8) #8 x 5/8" PHM screws and tighten securely. Figure 2.
D. Attach the rubber bumper toward the back of the slide in the middle hole.
043548XR6 Page 1 of 2

Figure 3 #8 x 5/8" PHSM
(3) req'd
Attaching the Slide Guard
3.
A. Slide the bracket with keyboard tray into the slide.
B. Using (3) #8 x 5/8" PHSM screws, attach the slide guard to the front of the slide. Figure3.
Slide Guard
A Flip the orks rface/desk pside
do n onto a non
abrasi e s rface
Attaching the Slide to desks with a Support Bar
4.
A
.
Flip
the
w
orks
u
rface/desk
u
pside
-
do
w
n
onto
a
non
-
abrasi
v
e
s
u
rface
.
B. Locate the slide perpendicular and about 1" from the front edge of the worksurface.
The slide should not be mounted closer than 8" to the nearest leg.
C. Place the spacer block and (5) spacers under the tray as shown in Figure 4.
D. Attach the slide, block and spacers using (6) #8 x 1-3/4" PHSM screws and tighten securely.
E. Attach the rubber bumper toward the back of the slide in the middle hole.
Attaching the Slide Guard
5.
A. Slide the bracket with keyboard tray into the slide.
B. Using (2) #8 x 5/8" PHSM screws, and (1) #8 x 1-3/4" PHSM screw, attach the slide guard to the front of the slide. Figure 5.
Slide Guard
Slide
#8 x 5/8" PHSM
(2) Req'd)
#8 x 1-3/4" PHSM Figure 5Figure 4
Spacer Block
Underside of
worksurface
Plastic Spacers
(5) Req'd
Slide
Rubber
Bumper
#8 x 1-3/4" PHSM
(6) Req'd
043548XR6 Page 2 of 2