Spectrum Industries Elite Lectern 55258 User manual

??
Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Important
Avant d’utiliser ce produit:
• Veillez à lire ce guide
• Respectez les consignes de sécurité et d’utilisation
• Vériez que vous disposez de toutes les pièces
nécessaires à l’installation
Importante
Antes de utilizar este producto:
• Lea este manual
• Cumpla con todas las instrucciones de prevención de
accidentes y operativas
• Revise que todas las partes y las cantidades correctas
estén incluidas
Any parts damaged during shipment must be reported within 5
days of receipt. To report information regarding missing parts or
damage, to purchase parts or accessories, or if you have any
questions, please contact us.
Thank you for purchasing Spectrum products!
Les pièces endommagées pendant le transport doivent faire
l’objet d’un rapport dans les 5 jours de leur réception. Veuillez
prendre contact avec nous si des pièces manquent ou sont
abîmées, si vous avez des questions, ou encore pour acheter
des pièces ou des accessoires.
Merci pour votre achat d’un produit Spectrum!
Si alguna parte se dañó durante el embarque, deberá reportarla
en un lapso de 5 días a partir de la recepción. Para reportar
cualquier información sobre partes faltantes o dañadas, para
adquirirlas o comprar accesorios, o bien, si tiene alguna duda,
póngase en contacto con nosotros.
¡Gracias por adquirir productos Spectrum!
Owner’s Manual
Le manuel du propriétaire
El manual del propietario
Video
Vidéo
Vídeo
Specs
Spécications
Especicaciones
800-235-1262
www.spectrumfurniture.com
Owner’s Manual
0118738R9 Page 1 of 17
Media Manager Elite Lectern™
55258
Media Manager Elite with surround,
left drawer, rack cube installed on right,
ip-up shelf on right
Media Manager Elite with overbridge,
right drawer, rack cube installed on left,
and toe kick, ip-up shelf on left

0118738R9 Page 2 of 17
Toe Kick
(included with select congurations)
(4) 0100167
8-32 x 1/2” PH
Thread-cutting screw
(2) 0118608
Side skirt
(1) 0118607
Audience-side skirt
(6) 053310
1/4-20 x 40mm
JC bolts
(4) 052605
1/4-20 x 15mm
JC bolts
(1) 025039
4mm Hex
wrench
Note: If the toe kick will be anchored to the oor, (4) fasten-
ers are required that will work with the 1/2” diameter holes
on the toe kick. Due to the wide variety of ooring materials
and conditions possible, anchor fasteners are not provided.
(1) 0118613
Toe Kick
(1) 0118614
Toe Kick Plate
Hardware

Figure 1A
Figure 1B
1. Install 3-piece skirt 4mm
0118738R9 Page 3 of 17
Assembly / Setup
Side skirt
Side skirt
8-32 x 1/2” PH
Thread-cutting screws
(4 required)
Audience-side skirt
Skirt Assembly
Instructor-side
Keyhole
slot
1/4-20 x 40mm JC bolt
(install from inside lectern)
Assembled skirt
1/4-20 x 40mm JC bolt
(install from inside lectern)
3. Hook the skirt keyhole slot at the end of each side skirt over the pre-
installed #14 x 7/8” PHSM screw. Figure 1C.
4. From inside the lectern (on audience-side) , install (2) 1/4-20 x 40mm
JC bolts through the base panel to secure the assembled skirt, and
tighten securely.
Figure 1C
Note: The skirt is designed to be easily re-
movable. It should be removed if the lectern
will be moved over long distances or thresh-
olds to prevent damage to the skirt panels.
Do not tip lectern to remove or install!
#14 x 7/8” PHSM
(pre-installed)
1. Attach the two side skirts to the audience-side skirt with (4)
8-32 x 1/2” PH Thread-cutting screws. Figure 1A.
2. Move lectern into position over the assembled skirt as
shown. Figure 1B.

0118738R9 Page 4 of 17
Audience-side Panel
The audience-side panel can be removed to access the rear portion of the rack
cube and lectern.
1. To remove the panel, open the document camera drawer fully.
Figure 2A.
2. Unscrew the (2) knobs inside the lectern behind the audience-side
panel and remove. Magnets are installed at the top corners of the
panel to prevent tipping. Figure 2B.
3. Carefully pull the top of the panel away from the lectern to release
the magnets, then lift the panel out. Figure 2C.
4. To replace the panel, insert the panel tabs back into base panel slots,
then tip the panel back up into position. Replace the knobs, and
tighten securely.
Figure 2A Figure 2B
Open document
camera drawer
Knobs
Audience-side
panel
Slots in base panel
Magnet inside each
upper corner
Figure 2C

11
/
32
”3
/
8”
0118738R9 Page 5 of 17
Quick-release Doors
The doors can easily be removed for easier access using the quick-
release hinge lever located on the upper hinge pin of each door.
Figure 3A. To remove, lift the lever while lifting out the door.
Figure 3A
Quick-release
lever
The doors can be switched to be hinged from the left or right-side.
To switch the hinge side:
1. Remove the door using the quick-release lever. Figure 3B.
2. Rotate the door 180°. Figure 3C.
3. The vented panel should be located on the bottom of the door.
Switch the lower vented metal panel with the upper acrylic panel
(requires removing or loosening 8-32 nuts.) Figure 3D.
4. Switch the corner hinge components as shown and tighten securely.
5. Re-install the door.
Figure 3B
Hinged on left
Hinged on right
3 4
1 2
Figure 3C
Figure 3D
180°

0118738R9 Page 6 of 17
Figure 5A
Figure 5
Quick-
release
lever
Optional Rack Cube
The removable rack cube (12RU) simplies installation and provides the ability to integrate equipment
remotely. The cube can be installed into the lectern at a later date. The cube also provides mounting
capabilities for multiple cooling fans if necessary. Compatible with most 4.75” cooling fans with 4.13”
mounting hole spacing (12 mounting locations available). Figure 5.
1. To remove the rack cube, open or remove the doors. Figure 5A.
2. Unscrew the #14 x 7/8” PHSM screw from the base, and slide out the cube. Figure 5.
• To move the rack cube to the other side of the lectern, all that is needed is to remove the (5)
bumper stops in the base panel with a 4mm hex wrench, and relocate them to the opposite side of
the base panel. The doors can easily be removed and switched using the quick-release levers.
Removable Rack Cube
(Can be installed on left
or right-side)
Primary Door
(Removable-can be installed
on left or right-side)
Secondary Door
(Removable-can be installed
on left or right-side)
(1) #14 x 7/8
PHSM to secure
cube to base
Keyboard Tray / Drawer
1. To ip, pull the tray out fully and locate the black plastic lever
on each slide. Figure 4.
2. Release the levers on the both slides while pulling the tray out.
3. Flip the tray over, re-align the slides, and push back in.
Note: Can be used as a keyboard tray, or ipped and used as a drawer.
Figure 4
Push here on both
slides to release
Keyboard Tray

0118738R9 Page 7 of 17
Optional Flip-up Shelf installation
Laminate Side Panel
(interior view)
Upper shelf
position holes
Lower shelf
position holes
Figure 6A
LaminateMetal
Proceed to Step 2
Installation video available
See www.spectrumfurniture.com
(8) 0100167
8-32 x 1/2” PH
Thread-cutting screw
(8) 051696
8-32 x 1” PHMS
(8) 021588
8-32 Keps Nut
(8) 0285
3/16 Flat Steel
Washer
Figure 6B
For laminate side panelsFor metal side panels
(1) 039622
2” Grommet
(1) Flip-up shelf
assembly
Attaching to laminate side panels:
1. Open the lectern door and remove the rack cube
(if equipped).
2. From inside the lectern, use a drill with a 3/16”
drill bit and slowly drill out the corresponding
pre-drilled pilot holes located on the laminate
side panel. Figure 6B. Masking tape can be
used on the exterior to minimize chip-out.
Drill with
3/16” drill bit
1. Determine:
• The side of the lectern the shelf will be installed. (Left or right). Note
the shelf will install on the opposite side as the drawer.
• The shelf position: (Upper or lower)
• Type of side panels your lectern has (metal or laminate) Figure 6A
26”D
[66 cm]
19.25”W
[48.9 cm]
7.5”H
[19 cm]
Figure 6

0118738R9 Page 8 of 17
CAUTION
Keep clear of pinch points during shelf movement.
Do not exceed 35 lbs [15.9 kg] of weight on shelf.
Operation
The shelf will automatically lock into place when lifted into the horizontal
position with the levers released. Figure 6E. To lower or ip-up the shelf,
press and hold the shelf bracket levers while slowly lowering or raising the
shelf. Do not move the lectern while the shelf is in the horizontal position.
Note: Power and communication wiring for document cameras, laptop
computers, and / or projectors placed on the ip-up shelf should be
routed on top of the audience-side of the shelf. Use of the shelf grommet
hole for wiring will result in pinching of the cords when the shelf is folded. Figure 6E
2. Attach shelf brackets to lectern:
1. Extend and lock each folding shelf bracket into the horizontal position.
2. Select the fasteners needed (Metal or laminate side panels)
3. Install the (4) lower screws into the side panel at the preferred height
leaving about 1/4” of threads exposed.
4. Set the shelf assembly onto the (4) lower screws using the notched brackets.
5. Secure the shelf assembly by installing the (4) upper screws.
6. Tighten all 8 screws securely.
7. Install 2” grommet in shelf.
Figure 6D
Metal side panel fasteners
(4) 8-32 x 1/2” PH Thread-cutting screws
2” Grommet
Flip-up shelf
(2) Folding
shelf bracket
Laminate side panel fasteners
(4) 8-32 x 1” PHMS
(4) 3/16” Flat steel washers
(4) 8-32 Keps nuts
Figure 6C
Shelf bracket
Laminate side panel
8-32 Keps nut
(use 11/32” wrench)
3/16” Flat steel
washer
8-32 x 1” PHMS in
3/16” drilled hole
from Figure 1B
8-32 x 1/2” PH
thread-cutting screws
(Install lower 4 rst)
3. Operation: Release lever
(press here)
Folding shelf
bracket

0118738R9 Page 9 of 17
Overbridge
panel
Note: Blank overbridge panels require the cus-
tomer to make necessary cutouts with a jigsaw
or router. This has a moderate difculty rating,
so experience and skill with tools is required.
1/4-20 x 35mm
JC bolt
(2 required)
Overbridge frame
2” grommet
Note: The overbridge panel is symmetrical. Rotating or ipping the panel
180° and re-attaching to the overbridge will allow you to place the cutout
on the opposite side of the overbridge if necessary.
Figure 7A
1. Before you begin, refer to the panel dimensions in Figure 7B for
maximum recommended cutout sizes.
2. Identify the size and position (left, centered, or right) of each cutout
needed.
3. Identify the depth of your device to verify it will not interfere with the
worksurface or any other objects under the overbridge when the
panel is attached. Figure 7C.
4. When the cutout location(s) have been determined, locate and mark the
exact cutout area(s) on the panel with a pencil. Note: Using masking
tape on cut lines will minimize laminate chipping while cutting.
5. Carefully make the cutout(s) in the panel using a jigsaw or router.
6. Set the panel into the overbridge frame opening. Note: It may be
necessary in some cases to install the electronic device into the
panel before attaching the panel to the overbridge.
7. Secure with (2) 1/4-20 x 35mm JC bolts and tighten securely.
8. Install (2) 2” grommets.
Tools Required
Jigsaw or routerDrill
Pencil Masking
tape
Drill bit
Measuring
Device
4mm
Optional Overbridge Insert Panel Cutouts

2” Grommet2” Grommet
0118738R9 Page 10 of 17
Figure 7B
Figure 7C
Max cutout area
Worksurface opening below
Worksurface
Overbridge
Section View
Overbridge panel
Note: The max cutout areas shown are general recommendations only.
The nal location of the cutout(s) on the panel will be determined by:
• The size of the cutout(s)
• Location preference of each
device (left, centered, right)
• The vertical depth of the installed device
• The available worksurface opening
under the overbridge on your specic
Spectrum lectern.
Note: The Overbridge Control Console™has been designed
for many of the currently available controllers on the market,
however, modied cutouts should be reviewed by Spectrum
to ensure clearance of brackets, keyboard slides, or other
objects under the worksurface.
Contact Spectrum to specify cutout size(s) and location(s).
Cutouts can be made in the blank insert panel by the
customer after the lectern has been purchased, but are
only recommended within the cutout area shown.