Spectrum Industries InVision Element Table 37128 User manual

Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Any parts damaged during shipment must be reported
within 5 days of receipt. To report information regarding
missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
Thank you for purchasing Spectrum products!
Spectrum Industries, Inc
925 First Avenue, Chippewa Falls, WI 54729 USA
800 235 1262
715 723 6750
www.spectrumfurniture.com
Owner’s Manual
0118729R2 Page 1 of 11
InVision Element Table™
37128

0118729R2 Page 2 of 11
• Read this owner’s manual before assembly or operation.
• Do not allow children to move the table.
• For indoor use only. Do not install or store the table where it will be
exposed to moisture.
• Do not block the ventilation openings.
• Do not allow anyone to sit, stand, or climb on the table.
• Use a damp, soft-cloth, or sponge, with mild soap or detergent solution
to clean dirty surfaces. Do not use harsh solvents or abrasives.
• This table is intended for institutional use. It does not have any user-
serviceable parts or user-maintenance requirements. If servicing is
necessary, please contact Spectrum Industries for assistance.
General Electrical Safety:
• Keep power switches in the OFF position before plugging or
unplugging from the wall outlet.
• Be sure total device / equipment load does not exceed 12-amps.
• Do not plug power cords into an extension cord.
• Inspect power cords for damage before each use. Do not use cords
that are damaged.
• Unplug power cord from electrical outlet by gripping the cord-do not
unplug by pulling only on the cord.
• Do not step on, drive over, drag, or place objects on power cords.
• For added safety, plug into a grounded outlet controlled by a GFI
(Ground Fault Interrupter) circuit breaker.
• Damaged electrical components can create signi cant hazards to
users and is not covered by the warranty. Repairs should always be
performed by a quali ed electrician.
• Electrical devices are not toys. Children are often unaware of the
hazards associated with electrical devices. This table must always
be used by adults or with adult supervision.
Warning - Relocating audio and/or video equipment to furniture not speci cally
designed to support audio and/or video equipment may result in death or
serious injury due to the furnishing collapsing or over turning onto a child.
Warning - Death or serious injury may occur when children climb
on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the
furnishing and as a result the furnishing may tip over on to the child.
Important Safety and Care Instructions

Note: One worksurface is included. The above information only applies to standard worksurfaces (without custom cutouts) only.
0118729R2 Page 3 of 11
Standard Worksurface
60”L x 42”W worksurface 72”L x 42”W worksurface 96”L x 42”W worksurface
• Blank
• 1 Cove cutout
• 2 Cove cutouts
• Display Stand
cutout
• 1 Cove cutout
• Display Stand
cutout
• 2 Cove cutouts
• Display Stand
cutout
Components
0118517
0118515
0118516
0118513
0118514
0118512
0118548
0118521
0118522
0118519
0118520
0118518
0118554
0118552
0118553
0118550
0118551
0118549

Corner Post Components
(2) 0100167
8-32 x 1/2” PH
thread-cutting screw
0118729R2 Page 4 of 11
T-Leg Components
(1) Tray-left
0118478 - 60”L Element
0118639 - 72”L Element
0118641 - 96”L Element
(4) Post Leg assembly
0118387 - 27”H
0118388 - 30”H
(2) T-Leg assembly
0118384 - 27”H
0118385 - 30”H
0118386 - 42”H
(1) Tray-right
0118477 - 60”L Element
0118638 - 72”L Element
0118640 - 96”L Element
(1) 0118483
End Cap
(8) 041289
1/4-20 x 1-3/4”
PHMS
(20) 026064
1/4-20 x 5/8”
PHMS
(4) 037779
5/16-18 Glide
(1) Lower Channel
0119863 - 60”L Element
0119584 - 72”L Element
0119601 - 96”L Element
(2) Side Panel
0119837 - 60”L Element
0119574 - 72”L Element
0119600 - 96”L Element
(1) 0119571
Front upright
Wire Tray Components AV Equipment Channel Components
(1) 0119572
Rear upright
(See p.8 for assembly)
(See p.6 for assembly)
(20) 0100167
8-32 x 1/2” PH
Thread-cutting
screw
(44) 026064
1/4-20 x 5/8”
PHMS
(4) 037779
5/16-18 Glide
(12) 052605
1/4-20 x 15mm
JC bolt
(2) 0100167
8-32 x 1/2” PH
Thread-cutting
screw
(See p.5 for assembly)
(See p.5 for assembly)
026064
1/4-20 x 5/8” PHMS
(20) - 60”L Element
(16) - 72”L Element
(12) - 96”L Element
(3) 059984
2” Snap-in
Grommet

Note: Start all screws by hand
to prevent cross-threading.
0118729R2 Page 5 of 11
Assembly / Setup
T-leg
Worksurface
1. Attach T-Legs to worksurface
1. Place the worksurface upside-down (laminate side-down) onto a at,
non-abrasive surface like another table. Figure A1.
2. Attach the two T-legs as shown with 1/4-20 x 1-3/4” PHM screws.
Make sure the holes on the vertical leg tubes face inward.
3. Install the four glides.
Phillips
screwdriver
Tools Required
Cordless drill with
Phillips driver
(best)
or
2. Attach Wire Tray to worksurface
1. Attach the left and right wire tray to the worksurface as shown
with 1/4-20 x 5/8” PHM screws. Figure A2.
2. Install the end cap with (2) 1/4-20 x 5/8” PHMS, and (2) 8-32 x
1/2” PH thread-cutting screws and tighten securely.
Glide
Wire Tray-left
(2) 8-32 x 1/2”
PH thread-cutting
screws
End cap
Figure A1
Figure A2
1/4-20 x 1-3/4” PHMS
(4 per)
(2) 1/4-20 x
5/8” PHMS
Phillips
screwdriver
Tools Required
Cordless drill with
Phillips driver
(best)
or
Note: Do not install the end cap if any power modules or
devices will be installed in worksurface cutouts later. This
will provide easier access during module installation.
One of the wire trays can also be left off to provide access.
Table with T-Legs and Wire TrayA
(When complete, proceed to p.7)
These holes
face inward
These holes
face inward
1/4-20 x 5/8” PHMS
(multiple required)
Wire Tray-right

Note: Start all screws by hand
to prevent cross-threading.
Table with Post Legs and Wire Tray
0118729R2 Page 6 of 11
Post leg
Worksurface
1. Attach Post legs to worksurface
1. Place the worksurface upside-down (laminate side-down) onto a
at, non-abrasive surface like another table. Figure B1.
2. Attach each post leg as shown with (8) 1/4-20 x 5/8” PHM screws.
3. Install the four glides.
Phillips
screwdriver
Tools Required
Cordless drill with
Phillips driver
(best)
or
2. Attach Wire Tray to worksurface
1. Attach the left and right wire tray to the worksurface as
shown with 1/4-20 x 5/8” PHM screws. Figure B2.
2. Install the end cap with (2) 1/4-20 x 5/8” PHMS, and (2)
8-32 x 1/2” PH thread-cutting screws and tighten securely.
Glide
(2) 8-32 x 1/2”
PH thread-cutting
screws
End cap
Figure B1
Figure B2
1/4-20 x 5/8” PHMS
(8 per)
(2) 1/4-20 x
5/8” PHMS
Phillips
screwdriver
Tools Required
Cordless drill with
Phillips driver
(best)
or
Assembly / SetupB
(When complete, proceed to p.7)
Wire
Tray
-left
Wire
Tray
-right
Note: Do not install the end cap if any power modules or
devices will be installed in worksurface cutouts later. This
will provide easier access during module installation.
One of the wire trays can also be left off to provide access.

0118729R2 Page 7 of 11
3. Flip Table upright
1. Carefully ip the table upright-this will take 3-4 people. Figure 3.
2. If necessary, adjust glides to level table.
Figure 3
CAUTION
Do not allow the legs to contact the oor until
the table is completely rotated. Side-loading
of the table legs could cause damage.
4. Power Modules and Wiring
1. If your worksurface has cutouts for optional power modules or other
components, install the devices then route and secure the cords
using the cord channel underneath. Figure 4.
2. If removed, install any remaining cord channels to the worksurface
with 1/4-20 x 5/8” PHM screws.
3. If removed, install the end cap with (2) 1/4-20 x 5/8” PHMS, and (2)
8-32 x 1/2” PH thread-cutting screws and tighten securely.
Figure A2, Figure B2.
Figure 4
Optional Power
module
Wiring
channel
Optional
Display
Stand
End cap
Cord Channel

Note: Start all screws by hand
to prevent cross-threading.
Assembly / SetupTable with T-Legs and AV Equipment Channel
0118729R2 Page 8 of 11
Lower
Channel
Rear Upright
(with grommet hole)
1. Assemble AV Equipment Channel
1. Attach the front and rear uprights to the lower channel with
1/4-20 x 5/8” PHM screws. (10 per upright). Figure C1.
2. Tighten securely.
3. Install the (3) 2” snap-in grommets.
Phillips
screwdriver
Tools Required
Cordless drill with
Phillips driver
(best)
or
2. Attach T-Legs to AV Equipment Channel
1. Install glides onto T-legs. Figure C2-1.
2. Attach each T-leg to the AV equipment channel with (6) 1/4-20
x 15mm JC Bolts and tighten securely. Figure C2-2.
3. Flip the entire assembly upright. (Glides down).
Front
Upright
Figure C1
4mm Hex
wrench
Tools
Required
T-leg
C
Figure C2.1
AV Equipment
Channel
(6) 1/4-20 x
15mm JC bolts
Glide
Figure C2.2
T-leg
1/4-20 x 5/8” PHMS
(8 per)
2” Snap-in
grommet
2” Snap-in
grommet
2” Snap-in
grommet

Display stand
Note: Start all screws by hand
to prevent cross-threading.
Note: The slots and tabs provided for the side panel can hold
the panel temporarily while the screws are being installed.
Note: Requires mounting holes and
cutout on at end of worksurface.
0118729R2 Page 9 of 11
3. Attach Worksurface
1. Move leg assembly into the nal location in the room.
2. Set the worksurface onto the assembled legs and align mounting holes. Figure C3.1.
3. Install (4) 1/4-20 x 40mm JC bolts through each leg to secure the worksurface. Figure C3.2.
4. Install (4) 1/4-20 x 5/8” PHM screws through each upright to secure the worksurface.
5. Tighten all screws securely.
6. If necessary, adjust glides to level table.
Worksurface
4. Side Panels
1. Install any worksurface-mounted or internal equipment and route all cables.
2. Secure the side panels using the slots and 1/4-20 x 5/8” PHM screws
into the worksurface. Figure C4.
Figure C4
Side Panel
Side Panel
1/4-20 x 1-3/4”
PHMS
(4 per leg)
1/4-20 x 1/2” PHMS
(4 per upright)
Figure C3.1
Figure C3.2
5. Display Stand
1. If you have the optional display stand, proceed with the installation
at this time. (Instructions included with stand.) Figure 5.
Phillips
screwdriver
Tools Required
Cordless drill with
Phillips driver
(best)
or
Figure 5

Element Display Stand - 37130
• Bolts directly to worksurface
• Integrated cable management routes and hides wires
• Adjustable (VESA-compatible) mount
• Requires worksurface mounting holes and cutout
Monitor size range: 32”-55” [81.3 cm-139.7 cm] diagonal
Weight capacity: 200 lb [45.4 kg]
Vertical adjustment
(worksurface-to-center)
• 23.5”H [59.7 cm]
• 21.5”H [54.6 cm]
• 19.5”H [49.5 cm]
• 17.5”H [44.5 cm]
• 15.5”H [39.4 cm]
(5 vertical positions
in 2” increments)
Tilting 15° range
Shipping weight: 35 lb [15.9 kg]
Display stand
Mounting holes and cutouts
needed on at end of worksurface
See spectrumfurniture.com for the latest
accessories and detailed warranty information.
Cutout required: 5.25”W [13.3 cm] x 2”D [5.1 cm]
(mounts to surface thicknesses up to 1.5”)
Power cord: 9’ [274 cm] with 90° at plug with 45° rotation
Power receptacles: 12A, 120 VAC spill-resistant
USB charging ports: 2.1A (10.5W)
Dimensions: 6”W [15.2 cm] x 2.5”D [6.35 cm] x 3.18”H
[8.1 cm]
Unit weight: 2.29 lb [1 kg]
Cove™Power Module - 99044
• Two power receptacles
• Two USB charge ports
(not data-compatible)
• Thumbscrew clamps
• Requires worksurface cutout
• ETL listed
• Available in Black or Silver
Accessories
(Available separately after initial congured purchase)
0118729R2 Page 10 of 11