Spectrum Industries 37317 User manual

0190035R1 Page 1 of 8
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Phillips
Screwdriver
Tools Required
Flex Flip Tables
37317
Hex wrench
(included
with base)
Figure 1A
(8) #14 x 7/8”
PHSM
Cables
Leg
mechanism
Worksurface
Figure 1B
Secure cables with (4) PHSM
screws & cable clips
(included with table legs)
Cable
Cable clip
Release
handle
1. Place worksurface face-down onto a non-abrasive surface.
2. Orient the leg mechanisms and release handle as shown and
align with the worksurface mounting holes. Figure 1A.
3. Attach the leg mechanisms and release handle to the worksurface
using (20) #14 x 7/8” PHSM screws and tighten securely.
4. Secure the cables to the worksurface with the included clips, (4)
#8 x 3/4” PHSM screws, and pre-drilled holes. Figure 1B.
Worksurface
1. Attach leg mechanisms & release to worksurface
(20) 0101382
#14 x 7/8” PHSM screw
(1) Worksurface
(1) 0106921
Table Base
(4) #14 x 7/8”
PHSM
User-side
(2) 053453
3/4” x 12” Hook and loop strap

0190035R1 Page 2 of 8
1. Set a leg on each leg mechanism. Figure 2.
2. Attach each leg with the included hex screws (4 per leg) and hex wrench.
3. Tighten screws securely.
4. Be sure swivel wheels are tightened securely. (Tighten with 1/2”
wrench if necessary.)
5. If you have wire management accessories proceed with step 3-if not,
carefully tip the table upright-this will require two people.
Figure 2
Hex screws
(included with
legs-4 required)
Leg
Leg
Leg
mechanism
2. Attach legs

0190035R1 Page 3 of 8
Wire management installation - Optional
1. Align the cord tray with the table mounting holes and attach with (4)
1/4-20 x 5/8” PHM screws. Figure 3A.
2. If you have a “Chalk white dry erase” worksurface, remove the
protective lm.
3. Determine which leg the channel will be attached (left or right). The leg should
be free of dirt, dust, grease and moisture to maximize tape adhesion.
4. Place the leg channel along the inside of one of the legs using the
adjustments holes as guides. Figure 3B. The channel can be
attached next to the buttons, but the buttons need to operate freely.
Do not install over the buttons or adjustment holes.
5. Remove the two tape backers and apply pressure to the channel
along the entire length to secure.
6. To install a Cove module, route power cord through cutout, then set
module into place and secure with thumbscrews. Figure 3C.
Adjustment
button
Leg
Figure 3AFigure 3B
2-sided tape
2-sided tape
Adjustment
button
L
e
g
C
h
a
n
n
e
l
(1) 0130711
Leg Channel
(1) 0130366
Optional Cord Tray
37318
(sold separately)
(4) 0101382
#14 x 7/8” PHSM
screw
(4) 1/4-20 x 5/8”
PHMS
Leg channel
(sold separately)
User-side
Optional Cord Tray
(1) 026057
#10 x 3/4” PHSM
screw
(1) 051070
Cord Clip
Note: Wire management accessories may or may not be included.

0190035R1 Page 4 of 8
1. To install a Cove module, route power cord through worksurface cutout
2. Place module into cutout and secure with thumbscrews. Figure 3C-3D.
3. Install each cord clip with (1) #10 x 3/4” PHSM screw to secure the
power cord under the worksurface. Figure 3E.
Figure 3F
Power cord
routed to oor
Leg channel
(sold separately)
8. If you do not have the optional leg channel, use the included
hook and loop straps to secure cords to the leg. Figure 3G.
Figure 3G
Figure 3D
8. If equipped, route the cords through the leg
channel and down to the oor. Figure 3F.
Figure 3C
Power cord
routed to oor
Worksurface
cutout
Hook & loop
straps
Cove Module
Figure 3E
Cord Clip
(1) #10 x 3/4” PHSM
Power Cord
Power cord
Thumbscrews
Worksurface
Cove Module

Female plug
0190035R1 Page 5 of 8
Installing “Easy Power Connection” - Optional
1. Place the Cove module into the worksurface cutout. Figure 4A.
2. Tighten the thumbscrews to secure to the worksurface. Figure 4B.
Figure 4B
Thumbscrews
Worksurface
Figure 4A
Worksurface
cutout
Cove Module
Figure 4D
Cord Clip
(1) #10 x 3/4” PHSM
Flexible metal conduit
Figure 4C
Right power cable
Left power cable
Cove Module
3. Plug the left and right power cables into the Cove module. Figure 4C.
4. Install each cord clip with (1) #10 x 3/4” PHSM screw to secure the
exible metal conduit under the worksurface. Figure 4D.
Cove Module
Male plug to
next desk
Female plug
Female plug

0190035R1 Page 6 of 8
Figure 4A
Figure 4CFigure 4B
Table operation
To adjust the worksurface height, press and hold the adjustment buttons
on one leg and raise or lower the worksurface and upper leg assembly
(slightly twisting then sliding the leg after the button has been pressed will
help keep it retracted until its aligned with the new hole.) Figure 4A. Align
the buttons with the adjustment holes to lock the leg into the new position.
Repeat this procedure on the other leg while making sure to use the same
hole position on both legs.
To ip-up the worksurface, pull the release lever and lift up the edge of
the worksurface until it locks into a vertical position. Figure 4B. To lower,
pull the release lever while lowering the worksurface-be sure it locks into
place. Multiple tables can be “nested” together next to a wall to save
space. Figure 4C.
Adjustment button on
each leg provides 9” of
total height adjustment
in 1” increments
Accessories
Release Lever
Leg Channel - 37318
• Provides ability to route wires and cables from the oor to the
worksurface (Use with Cove or other power modules-not included)
• High-impact polystyrene
• Color-black or silver
• Installs with double-sided tape
• Internal size (nominal):
1.75”W [4.44 cm] .5”D [1.27 cm] x 15”H [30.5 cm]
• Shipping weight (nominal): 1 lb [.454 kg]
Silver Black
2” Dia
15”

72” Table
60” Table
48” Table
0190035R1 Page 7 of 8
Worksurface cutout requiredCove Module available in Black or Silver
• Each table accommodates one power connection kit
• Each row also requires one 99050 starter
• Typical installations do not exceed 6 or 7 Easy Power
Connection Kits (or tables) per row (or circuit).
Cutout required: 5.25”W [13.3 cm] x 2”D [5.1 cm]
Power cord: 15A
Power receptacles: 12A, 120 VAC spill-resistant (2 receptacles)
USB charging ports: 2.1A (10.5W) (2 USB charging ports)
Cove dimensions: 6”W [15.2 cm] x 2.5”D [6.35 cm] x 3.18”H [8.1 cm]
Shipping weights: 99047 - 3.5 lb [1.59 kg]
99048 - 4 lb [1.82 kg]
99049 - 4.5 lb [2.04 kg]
99050 - 2.5 lb [1.14 kg]
• Each table accommodates one
power connection kit
• Two AC power receptacles
• Two USB charge ports
(not data-compatible)
• Requires 5.25”W x 2”D
worksurface cutout
• Flexible metal conduit is secured
to worksurface underside
• Cove is ETL listed
• Thumbscrew clamps
• Cove available in Black or Silver
• Starter connects to standard
3-prong wall outlet
99047 - 48”W Easy Power Connection Kit
99048 - 60”W Easy Power Connection Kit
99049 - 72”W Easy Power Connection Kit
99050 - Starter Kit (One per row required)
99049 - 72” Kit
99048 - 60” Kit
99047 - 48” Kit
Easy Power Connection Kit with Cove™Power Module
99050 - Starter Kit
(One per row required)
includes 20-15A adapter cord
To wall
outlet
See spectrumfurniture.com for the latest
accessories and detailed warranty information.

0190035R1 Page 8 of 8
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products is manufactured from the best materials available and each
product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table below
from the date of delivery. This warranty shall not apply to defects or damage resulting from misuse, abuse, neglect, improper care, modifi cation or repair not
authorized by Spectrum, or any other cause outside the control of Spectrum. Spectrum will, at its sole option, either repair or replace the defective product.
This warranty is exclusive; no other warranty, written or oral, is expressed or implied. This warranty is given by Spectrum to Buyer and to no other per-
son or legal entity. No Spectrum dealer, distributor, agent or employee is authorized to make any modifi cation or addition to this warranty.
NOTWITHSTANDING ANYTHING TO THE CONTRARY, SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR LIQUI-
DATED DAMAGES, INCLUDING CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES. IN NO EVENT SHALL SPECTRUM’S LIABILITY, WHETHER
UNDER CONTRACT OR WARRANTY, IN TORT OR OTHERWISE, EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM FOR THE PRODUCT AT
ISSUE AND “RECALL ACTION” EXPENSES. SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES, WHETHER ARIS-
ING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORIES OF LAW, WITH
RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATING THERETO.
Our Customer Service Department is ready to provide immediate attention to any questions, comments or concerns. They are available to answer your calls
Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome via e-mail at: [email protected].
Item Warranty Period
effective 1/1/2015
Adjustable Crank / Electric Desk Legs • 1 Year
Flat Panel Desk Gas Cylinders
Chairs
• Adjustable Height Chair Parts – including frames, gas
cylinders, wood and plastic parts, control handles, casters
• Adjustable Height Chair Upholstery
• In-Stock Upholstery
• Graded-In Fabrics and Customer Owned Material
• 7 Years
• 2 Years
• 2 Years
• No Warranty
Height Adjustable Columns and Lifts • 1 Year
General Use Casters
Electrical (including timers and LINAK actuators) • 2 Years
Keyboard / Mouse Trays • 1 Year
Flat Panel Monitor Arms
• Flat Panel Monitor Arm – General Parts
• Flat Panel Monitor Arm – Gas Cylinders
• 5 Years
• 2 Years
Desks and Lecterns
• Computer Desk Chassis
• Cart Chassis
• Lectern Chassis
• 10 Years
Warranty Table
Warranty
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2017 Spectrum Industries Inc., All rights reserved.
8
DESIGNED AND ASSEMBLED IN
CHIPPEWA FALLS
WISCONSIN.USA