Spectrum Industries 67066 User manual

Assembly Instructions:
Tools Required:
Phillips screwdriver
Glide wrench (included)
Before you begin, please make sure all parts and proper quantities are
included. Any parts damaged during shipment must be reported within
1f f f
(4) 025068
5/16-18 Glide
(1) 025069
Glide wrench
(15) 026064
1/4-20 x 5/8" PHMS
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!
(1) 037749
Unit-to-unit bracket
Multi-Use Student Desks
27½"H
#67066 (48"W)
#67067 (60"W)
#67068 (72"W)
29½"H
#67166 (48"W)
#67167 (60"W)
#67168 (72"W)
(4) 041289
1/4-20 x 1-3/4" PHMS
(1) 036281
Dual Unit-to-unit bracket
(1) 042948
Grommet
15 days of receipt. To report information regarding damages or if you
have any questions, please call 1-800-235-1262.
Attach Legs and Sway Brace to Worksurface
1.
A. Place the worksurface face-down onto a non-abrasive surface.
B. Orient and align the left and right legs as shown with the
worksurface and sway brace. Make sure the grommet hole
is on the back side of the desk. Figure 1.
C. Secure with (4) 1/4-20 x 1-3/4" PHM screws, but do not tighten
completely.
D. Install the (4) glides-these can be adjusted after the desk is
assembled.
Figure 1
Glides (4 req'd)
1/4-20 x 1-3/4"PHMS
(4 req'd)
Leg
Sway Brace
Worksurface
044170XR3 Page 1 of 2

Attach Cord Channel
2.
A. Desks can be attached together in a row if necessary. To connect, line up the desks side-by-side in
their final location with the worksurfaces touching.
B. Attach the unit-to-unit brackets to the bottom of the worksurface as shown with 1/4-20 x 5/8" PHM
screws. Figure 3. The dual bracket will go on the back of the worksurface.
C. Attach the cord channel extension to both desks with 1/4-20 x 5/8" PHM screws.
Connecting desks together
3.
Dual unit-to-unit Bracket
(attach w/ four 1/4
20 x 5/8
"
PHMS)
A. Attach the cord channel to the legs and worksurface with
(8) 1/4-20 x 5/8" PHM screws. Figure 2.
B. Tighten all screws securely.
C. Turn desk upright-this may require two people.
Desk #2
1/4-20 x 5/8" PHMS
(8) Req'd
Figure 2
Cord Channel
Rear edge of
worksurface
Leg
Figure 3
1/4-20 x 5/8" PHMS
(2 Req'd)
(attach
w/
four
1/4
-
20
x
5/8
PHMS)
Cord channel extension
(attach w/ four 1/4-20 x 5/8" PHMS)
Unit-to-unit
bracket
Desk #1
A. To route cords and wires, remove the grommet from
the desk cut-out.
B. Remove the center cover and cord receptacles. Figure 4A.
C. Turn the receptacles around as shown in Figure 4B. Route
the cords through the notches and re-attach the cord
receptacles by sliding them into the grommet frame.
D. Replace the grommet frame with the center cover into the
worksurface cut-out. Figure 4C.
Grommet set-up
4.
Figure 4CFigure 4BFigure 4A
Center Cover
Cord Receptacle
Grommet
Frame
044170XR3 Page 2 of 2