Spectrum Industries Esports 37418 User manual

Assembly Instructions
A .3125” [7.9 mm]
B 1” [25.4 mm]
C .983” [25 mm]
D 2.07” [52.5 mm]
E .987” [25.1 mm]
Re-programmable 4-digit Combination Lock - 95536
• Set your own 4-digit personalized combination (up to 10,000 options)
• 5/16” hardened steel shackle for cut-resistance
• Black powdercoated die-cast body for durability
• Change key included
• Unit weight: .55 lb [.25 kg]
Verrou à combinaison à quatre chiff res reprogrammable - 95536
• Réglez votre propre combinaison personnalisée à quatre chi󰀨 res (jusqu’à
10 000 options)
• Arceau en acier durci de 7,9 mm (5/16 po) pour résistance aux coupures
• Corps moulé enduit de poudre noire pour une durabilité accrue
• Clé de rechange comprise
• Poids de l’unité : 0,25 kg [0,55 lb]
Bloquo reprogramable con combinación de 4 dígitos: 95536
• Ajuste su combinación personalizada de 4 dígitos (hasta 10 000 opciones)
• Grillete de acero reforzado de 5/16” con resistencia de corte
• Cuerpo de fundición a presión con recubrimiento de polvo negro que
refuerza la durabilidad
• Se incluye una llave de cambio
• Peso de la unidad: .55 lb [.25 kg]
0193702 Page 1 of 6
Assembly Instructions
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Esports Locker
37418
(4) 0106543
1/4-20 Keps
nut
(12) 035728
1/4-20 x 1/2”
PHMS
(12) 0100167
8-32 x 1/2” PH
Thrd ctg screw
(2) 0160548
Corner
Bracket
Assembly tip: Do not tighten component fasteners com-
pletely until all have been installed. Keeping them loose
will help with alignment between parts during assembly.
(1) 0190404
Re-programmable
padlock
(1) 0172173
Base
(labeled ‘D’)
(1) 0119448
Plastic storage
tray
(1) 0171993
Rear Panel
(labeled ‘C’)
(1) 0171994
Left side panel
(labeled ‘B’)
(1) 0172177
Top panel
(labeled ‘A’)
(1) 0172231
Door Assembly
Parts Bag
(1) 0171994
Right side panel assembly
(w/ hasp and magnet)
(labeled ‘B’)

0193702 Page 2 of 6
Attach side panels to rear panel
1. Place rear panel ‘C’ ange side-down as shown onto a at surface.
2. Align the tabs of the back panel with the side panel slots.
2
Right side panel ‘B’
Left side panel ‘B’
Rear panel ‘C’
3. Pull / push the panels as shown to lock tabs into place.
All three panels should be aligned at the bottom edge.
Aligned edges
Lock hasp and
magnet pre-installed
Attach corner brackets to top panel
1. Attach each corner bracket to the top panel (labeled ‘A’)
as shown with (2) 8-32 x 1/2” PH Thrd ctg screws.
2. Do not full tighten screws-they should be loose enough to
allow some movement during assembly.
1
8-32 x 1/2” PH
Thrd ctg screw
(2 per)
Corner
Brackets
Top panel
(labeled ‘A’)

0193702 Page 3 of 6
Attach top and base panels
1. Align the tabs of the side panels with the top and base panel slots.
3
Base panel ‘D’
Top panel ‘A’
2. Push the panels down to lock tabs into place. Make sure all panels
are aligned.
3. Install the remaining (2) 8-32 x 1/2” PH Thrd ctg screws in each
corner bracket but do not tighten completely.
Secure panels
1. Carefully tip the locker assembly upright.
2. Install (4) 1/4-20 x 1/2” PHM screws at the rear panel
to secure the assembly.
3. Securely tighten ALL screws at this point.
4
(4) 1/4-20 x 1/2”
PHMS
Attach door assembly
1. Open the hinge and attach the door assembly to the left
panel edge with (4) 8-32 x 1/2” PH Thrd ctg screws.
2. Tighten screws securely.
5
Door assembly
Rear panel
(4) 8-32 x 1/2”
PH Thrd ctg screw
8-32 x 1/2” PH
Thrd ctg screw
(2 per)
Right side panel ‘B’
Left side panel ‘B’

1/4-20
Keps nut
1/4-20 x 1/2”
PHMS
1/4-20 x 1/2”
PHMS
0193702 Page 4 of 6
Connect lockers together
6
Optional 95041
toekick
X4 X4
Fasteners for
side-to-side
connection
Fasteners for
lower-to-upper
connection
Lower-to-upperLower-to-upper
Side-to-side
Side-to-side

Stacked 3 high on
optional toekick
Stacked 2 high on
optional toekick
Single on
optional toekick
Optional
toekick Optional toekick
Optional
toekick
0193702 Page 5 of 6
Wall
Free-standing back-to-back island
(lockers bolted together)
Anchored to wall
(lockers bolted together)
Due to the wide variety of wall materials, wall anchor fasteners
are NOT provided. Individual job conditions as well as state/local
building codes will dictate the type of installation fasteners and
how the lockers must be anchored.
(5) 5/16” holes on rear
for customer-supplied
wall anchors
13”
17.67”
Rear panel
Stacking Guidelines
Wall anchoring