Spectrum Flip-up Shelf for Link Lectern Installation guide

Assembly Instructions
Tools
Required
Attaching to Laminate Side Panels:
1. Open the lectern door and remove the rack cube (if equipped).
2. From inside the lectern, use a drill with a 3/16”
drill bit and slowly drill out the corresponding
pre-drilled pilot holes located on the laminate
side panel. Figure 1B. Masking tape can be
used on the exterior to minimize chip-out.
Note: There are (2) holes needed for the upper
position, and (4) needed for the lower position.
Drill with
3/16” drill bit
0120368R2 Page 1 of 2
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Flip-up Shelf
for Link Lectern™
55385
(1) 039622
2” Grommet
Phillips
screwdriver
26”D
[66 cm]
15.25”W
[38.7 cm]
7”D
[17.8 cm]
(1) 0120069
Flip-up shelf assembly
Determine:
• Side of the lectern the shelf will be installed. (Left or right-side)
• Upper or lower shelf position
• Type of side panels your lectern has (metal or laminate) Figure 1A
1. Before You Begin
Figure 1A
LaminateMetal
Figure 1B
Laminate Side Panel
(interior view)
Upper shelf
position
holes
Lower shelf position holes
Proceed to Step 2
Upper shelf
position
holes
(4) 0100167
8-32 x 1/2” PH
Thread-cutting screw
(4) 051696
8-32 x 1” PHMS
(4) 021588
8-32 Keps Nut
(4) 0285
3/16 Flat Steel
Washer
For laminate side panelsFor metal side panels

Figure 3
2. Attach Shelf Brackets to Lectern
Figure 2A
1. Remove the instructor-side door and audience-side panel.
2. Extend and lock each folding shelf bracket into the horizontal
position. Figure 2A.
3. Align and attach each bracket to the side of the lectern using:
4. Tighten all screws securely.
5. Install 2” grommet in shelf.
Shelf bracket
8-32 x 1” PHMS
8-32 Keps nut
(use 11/32” wrench)
3/16” Flat steel
washer
Laminate side panel
3/16” drilled hole
from Figure 1B
Figure 2B
Metal side panels
Figure 2A
Laminate side panels
Figure 2B (a 2nd person
to assist may be required)
(4) 8-32 x 1/2” PH Thread-
cutting screws
(4) 8-32 x 1” PHMS
(4) 3/16” Flat steel washers
(4) 8-32 Keps nuts
Metal side
panel
0120368R2 Page 2 of 2
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2016 Spectrum Industries Inc., All rights reserved.
3. Operation
The shelf will automatically lock into place when lifted into the horizontal
position with the levers released. Figure 3. To lower or ip-up the shelf,
press and hold the levers under each folding shelf bracket at the same
time while slowly lowering or raising the shelf. Do not exceed a maximum
of 35 lb of weight on the shelf. Do not move the lectern while the shelf is
in the horizontal position.
Note: Power and communication wiring for document cameras, laptop
computers, and / or projectors placed on the ip-up shelf should be routed
on top of the audience-side of the shelf. Use of the shelf grommet hole for
wiring will result in pinching of the cords when the shelf is folded.
CAUTION
Keep clear of pinch points during shelf movement.
Do not exceed 35 lbs [15.9 kg] of weight on shelf.
Release lever
(press here)
Folding shelf
bracket
8-32 screws
(2 required per
bracket)
Flip-up shelf
assembly
2” Grommet