Spectrum 3736 User manual

37362 - (1 desk) 37363 - (3 desks) 37364 - (5 desks) 37365 - (6 desks) 37366 - (10 desks) 37367 - (16 desks)
PART# ITEM
1 1 1 1 1 1 0192177 4-Pin Connector
1 1 1 1 1 1 0192178 6” Driver adapter
1 1 1 1 1 1 0192179 12 volt power supply
1 1 1 1 1 1 0192180 12” RGB F to M cable link
1 3 5 6 10 16 0192181 Plus shape connector
1 1 1 1 1 1 0192182 LED Controller
& RF Remote
- 2 4 5 9 15 0192183 72” Interconnection cable
2 6 10 12 20 32 0192272 6” Interconnection cable
2 6 10 12 20 32 0192265 4” RGB LED Tape light
1 3 5 6 10 16 0156657 LED Light bracket
2 6 10 12 20 32 0101911 #14 x 3/4” PHSM
Assembly InstructionsAssembly Instructions
0192185 Page 1 of 2
Assembly InstructionsAssembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
LED Lighting Kit for Esports DesksLED Lighting Kit for Esports Desks
37362 - (1 desk)37362 - (1 desk)
37363 - (3 desks)37363 - (3 desks)
37364 - (5 desks)37364 - (5 desks)
37365 - (6 desks)37365 - (6 desks)
37366 - (10 desks)37366 - (10 desks)
37367 - (16 desks)37367 - (16 desks)

2
0192185 Page 2 of 2
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2020 Spectrum Industries Inc., All rights reserved.
1. Attach LED light bracket1. Attach LED light bracket
1. Attach the LED light bracket centered under the
worksurface with (2) #14 x 3/4” PHSM screws. Figure 1.
1. Connect the components under the worksurface as shown while
routing them through the desk cord channel. Figure 3.
(Note plus connector and LED tape will not go in the cord channel.)
3. Connect LED components3. Connect LED components
Worksurface
Figure 2
LED light
bracket
#14 x 3/4” PHSM
(2 required)
Figure 1
2. Apply LED tape to bracket2. Apply LED tape to bracket
1. Apply the (2) 4” LED tape strips to the bracket anges with the
connectors pointing toward the cord channel. Figure 2.
4” LED
light tape
4” LED
light tape
Connectors
toward cord
channel
LED light
bracket
Cord channel
Figure 3
4-pin connector
4” LED tape 4” LED tape
Plus connector
4-pin connector
LED Controller
12V Power supply
(connect to power
strip or wall outlet)
6” Driver
adapter
12” RGB
F-to-M link
72” interconnection cable
to plus connector on next desk
LED light
bracket
6” Interconnection cable 6” Interconnection cable
Cord channel