Spectrum GG Gaming Desk 37421 User manual

Assembly Instructions
0193831 Page 1 of 7
Assembly Instructions
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
GG Gaming Desk
(36”, 44”, 60” and 72”W)
37421
(8) 035728
1/4-20 x 1/2”
PHMS
(1) Stretcher
(1) 025069
Glide Wrench
Assembly tip: Do not tighten component fasteners completely
until all have been installed. Keeping them loose will help with
alignment between parts during assembly.
(4) 037779
5/16-18 x 1”
Glide
(13) 0101382
#14 x 7/8” PHSM
X2
(10) 0100167
8-32 x 1/2” PH
Thrd ctg screw
(1) 0176848
Unit-to-unit
bracket
(1) 0176830
Tab
(1) Worksurface
(1) Modesty
panel
(1) Cord channel
bottom
(1) Cord channel
front
Parts will be for 36”, 44”, 60”, or 72”W depending on size ordered.
(2) 0174452
Leg cover
(1) Top cover
Leg height
Legs are factory-assembled for a 28”H worksurface but are adjustable
from 24”-30”H (in 2” increments). If a di󰀨erent worksurface height is
needed, remove the 4 screws in each leg, re-adjust to the new height, and
re-install screws. Make sure both legs are set to the same height.
(1) 0174258
Left leg (1) 0174681 Right leg

0193831 Page 2 of 7
Attach modesty panel and tab
1. Attach the modesty panel to each leg with (1) 1/4-20 x 1/2” PHM
screw in the position shown only.
2. Attach the tab to the worksurface with (1) #14 x 7/8” PHSM screw.
3. Secure the pivoting leg to the worksurface with the (2) remaining
#14 x 7/8” PHSM screws.
2
(1) 1/4-20 x 1/2”
PHMS (1) #14 x 7/8”
PHSM
Tab
(2) #14 x 7/8”
PHSM
Modesty panel
(1) 1/4-20 x 1/2”
PHMS
Worksurface
Pivoting leg
Attach legs to worksurface
1. Place the worksurface face-down onto a non-abrasive surface.
2. There is a left and right leg. Orient each leg with the screw hole
(next to bumper) on the outside edge of the worksurface.
3. Attach one leg to the worksurface with (3) #14 x 7/8” PHSM screws.
4. Attach the other leg with (1) #14 x 7/8” PHSM screw at the front
only so it can pivot slightly.
1
Worksurface
(1) #14 x 7/8”
PHSM
Right leg
Left leg
User-side
(3) #14 x 7/8”
PHSM
User-side
Pre-drilled hole
for tab is on
audience-side
Audience-side
Screw hole toward
outside edge
(Pivoting)
Worksurface
outside edge
Bumper

X4
0193831 Page 3 of 7
Attach cord channel
1. Attach the front cord channel to the worksurface with #14 x 7/8” PHSM screws. (3
or 4 depending on desk width). Install (1) 1/4-20 x 1/2” PHM screw into each leg.
2. Hook the cord channel bottom tabs into the cord channel front slots.
3. Secure the cord channel bottom to each leg with (1) 1/4-20 x 1/2” PHM screw.
3
1/4-20 x 1/2”
PHMS
(3 or 4) #14 x 7/8”
PHSM screws into
worksurface
1/4-20 x 1/2”
PHMS
Cord channel
bottom
Cord channel
front
Attach stretcher
1. Attach the stretcher to each leg with (4) 8-32 x 1/2”
PH Thrd ctg screws.
4
Install glides
1. Install (4) glides. Adjustments can be made later for uneven oors.
5
(4) 8-32 x 1/2” PH
Thrd ctg screws
Stretcher
Glide
1/4-20 x 1/2”
PHMS

0193831 Page 4 of 7
Flip desk upright
1. Carefully ip the desk upright. This will require at least two people.
6
Install top cover screws (optional)
1. Install (1) 8-32 x 1/2” PH Thrd ctg screw on the outside hole
on the top of the leg (next to the rubber bumper).
2. Repeat on other leg.
7
X2
8-32 x 1/2” PH
Thrd ctg screws
Rubber
bumper
Install leg covers
1. Attach each leg cover to a lower leg with (2) 8-32 x 1/2” PH Thrd ctg
screws.
8
(2) 8-32 x 1/2” PH
Thrd ctg screws
Leg cover
These screws help keep the top cover in place.

0193831 Page 5 of 7
Install top cover panel
1. Set the top cover over the rubber bumpers.
9
If a monitor arm will be clamped to the worksurface, slide the top cover
panel back. Cords and wires can be routed through the gap in front.
Slide the top cover panel forward. Cords and wires can be
routed through the gap behind.
Monitor arm
Top cover
panel
Monitor arm

0193831 Page 6 of 7
Connecting desks together (optional)
Installing LED strip light tape (optional)
Access
port
Audience-side panel
Customer-supplied
LED strip light
Note: Access ports are provided at the top of the audience-side panel
that provide the ability to route customer-supplied LED strip light tape
inside the top channel. This illuminates the audience-side panel and can
help highlight any team branding logos that are being used or just provide
accent lighting to the desk.
Unit-to-unit
bracket
(2) 1/4-20 x 1/2”
PHMS
Behind front legs

0193831 Page 7 of 7
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Warranty
1-800-235-1262
Toll-free HELPLINE
[email protected]
© 2023 Spectrum Industries Inc., All rights reserved.
We will make it right for you!
Thanks for choosing Spectrum! Spectrum is committed to provide complete customer satisfaction.
Each of our products is manufactured from the best materials available and each product is strin-
gently monitored throughout the production process through our P.A.C.E. program (Product Assur-
ance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from
defect for the period set out in the warranty from the date of delivery.
For a listing of all product specifi c warranty terms please visit our website at:
https://www.spectrumfurniture.com/en/resources/purchasing-terms-warranty