Spectrum 95500 User manual

Adjustable CPU Sling
#95500
Assembly Instructions:
042023XR9 Pa
g
e 1 of 2
Before you begin, please make sure all parts and proper quantities are included. Any parts damaged during shipment must be
reported within 15 days of receipt. To report information regarding damages or if you have any questions, please call 1-800-235-
1262.
A. Determine the height and width required for your CPU.
B. Adjust the CPU Sling to the height and width of your CPU using the three adjustment holes and attach the
corner brackets to the CPU sling using the 1/4-20 x 3/8" Truss Head Machine screws and 1/4-20 Locknuts as
shown in Figure 1. The screws install from the inside with the locknuts on the outside. Note the positions of the
corner brackets for the top and bottom sides of the CPU sling (Figure 1A.)
1. ASSEMBLING & ADJUSTING CPU SLING
(4) 026547
1/4-20 x 1-1/2 PHMS Tools Required:
Phillips head screwdriver
7/16" wrench
Drill with an 1/8" bit (for desks without threaded inserts)
(4) 026017
1/4-20 x 1/2
PHMS
(1) 042110
2" x 2" x 1" Shim
(1) 042019
Leg Bracket
(1) 042139
Drill template
(6) 041943
1/4-20 Locknut
(4) 021605
#10 x 1-3/4 PHSM
(4) 026057
#10 x 3/4 PHSM
(2) 044890
1 x .275 ID x .5
OD Nylon Spacer
(7) 042025
1/4-20 x 3/8
THMS
Figure 1
1/4-20 x 3/8" THMS
Bottom
Locknut
Corner Bracket Top Side
Corner Bracket Figure 1A
(2) 042021
Corner Brackets
These are used with 48" 60" and 72" desks

A
. Determine whether the CPU Sling will mount on the right or left side of the desk and align the top sling holes with the
appropriate set of inserts. Figure 2 shows a sling being mounted on the left side of a desk.
B. Attach the Sling to the worksurface using (4) 1/4-20 PHM Screws and tighten.
Note: Desks without support brace use two 1/4-20 x 1/2" PHM Screws (026017.) For desks with Support Brace as in Figure 2A, use (2)
Nylon Spacer (044890) in the front hole, and the Back Support Shim (042110) in the rear holes with the longer 1/4-20 x 1-1/2" PHM Screws
(026547.) The front of the sling will extend past the Support Brace.
2. ATTACHING SLING TO DESKS WITH THREADED INSERTS
Figure 2 Figure 2A
1/4-20 x 1-1/2"
PHM Screw
Shim
Nylon Spacer
3. ATTACHING SLING TO DESKS WITHOUT THREADED INSERTS
Figure 3A
Drill
Tem
p
late
Leg
Worksurface
Support Brace
(on some desks)
3/4" Deep
Figure 3
Drill here
Drill here
A. Determine whether the CPU Sling will mount on the right or left side of the desk.
B. Fold and tape the enclosed Drill Template (042139) to the underside of the worksurface in the position shown in
Figure 3. Wrap a piece of tape around a 1/8" drill bit to mark 3/4" from the end of the bit - Figure 3A. Carefully drill
through the Template on the four marked holes, 3/4" deep (see Figure 3.)
C. Attach CPU sling to worksurface using (4) #10 Sheet Metal Screws.
Note: Desks without threaded inserts or Support Brace use (4) #10 x 3/4" PHSM Screws (026057.) Desks without inserts that include a
Support Brace as in Figure 3, use (2) Nylon Spacers (044890) in the front holes, and one Back Support Shim (042110) in the back holes
using the longer #10 x 1-3/4" PHSM Screws (021605.) The front of the CPU Sling will extend past the Support Brace.
4. ATTACHING LEG BRACKET
A. Line up the Bracket with the front slot of the CPU Sling as
shown and attach with 1/4-20 x 3/8" THM Screw (042025)
(Figure 4)
B. Adjust the Leg Bracket until it is snug against the Leg and
tighten screw.
Note: If the CPU Sling is being used on a CLASS™ or Evolution™ desk, the
included (042019) Leg Bracket should be attached to the Sling and Front Leg.
Figure 4
Note: If desk does not have threaded inserts, skip to step #3
Support Brace
Insert holes
1/4-20 x 1/2"
PHM Screw
DESKS WITHOUT SUPPORT BRACE DESKS WITH SUPPORT BRACE
042023XR9 Pa
g
e 2 of 2
1/4-20 x 3/8" THMS
Leg Bracket
1/8" Drill Bit