Spectrum Oxford Series User manual

Logo/Company Name
4”w x .75”h
Assembly Instructions
2
1
3
5
6
7
4
CASTERS/GLIDES
8
CASTERS/GLIDES
8
1) Remove base, back/back bar, pneumatic
cylinder, casters/glides, and seat from box.
2) Put casters or glides on base. Use pressure to
push in (8).
3) Slide optional foot ring (4) over pneumatic
cylinder from bottom (2) about halfway up
the cylinder and tighten knob (7).
4) Place base with legs on hard level surface (1).
5) Insert pneumatic cylinder as shown in (2)
into center hole of base and lightly push
down. Adjust foot ring to desired height.
6) Turn seat upside down to assemble back. It
may be helpful to lay the seat on the edge of
a table to slide the back bar into position.
7) Loosen knob (6) counter clockwise slightly
to allow the back bar to slide into the control
mechanism on the seat. Push in until you
hear it click. Then tighten by turning knob (6)
clockwise, do not overtighten.
8) Turn seat and back over and align the center
hole on the bottom of the seat with the top
of the pneumatic cylinder and lightly push
down. With the weight of your body, carefully
sit on the seat. This will press the base,
pneumatic cylinder, and seat together.
9) To raise the height of your chair simply pull
up on lever (5) while not seated.
10) To lower the height of your chair, while
seated on chair, pull up on lever (5).
In/Out and Up/Down back adjustments not available on all options.
CSO-05

Logo/Company Name
4”w x .75”h
Assembly Instructions
1) Remove base, back/back bar, pneumatic cylinder, seat,
foot ring (if included) and casters/glides from box.
2) Place base (1) upside down and insert casters/glides (5)
(see gure 1).
3) Slide optional foot ring (4) over pneumatic cylinder from
bottom (2) about halfway up the cylinder and tighten knob (7).
4) Flip the base so casters/glides are on the oor and insert
pneumatic cylinder (2) as shown in (gure 3) into center
hole of base with colored button up. Lightly push down.
Adjust foot ring to desired height.
5) Align the center hole of the underside of the seat assembly
(3) with the top of the pneumatic cylinder (2) and lightly
push down. Kneel on the seat to hold it together. This will
press the base, pneumatic cylinder and seat together.
(Underside of the seat is shown in Figure 2)
6) On the chair back bar, depress the spring loaded button
with your nger, lift the back release. (DO NOT PUSH THE
BAR ALL THE WAY THROUGH AT THIS TIME.)
7) Now, push the bar down until it protrudes at least 1” below
the channel. (You should hear the spring-loaded button click
open as it comes out the bottom of the channel). Adjust
the height of the seat back for comfort and push the back
release down to lock the bar in place.
8) Adjust the seat back to the desired angle using the control
lever located on the side of the seat. You can adjust the
height of the back by lifting the back release up. Push the
back release(9) down to lock the bar in place.
9) To raise the height of your chair, take your weight off of the
chair and pull up on the lever (8) on the underside of the
seat and adjust.
10) To lower the height of your chair you must be seated with
your weight on the seat, lift up on lever (8).
6
2
1
3
4
7
5
SEAT
BACK RELEASE
CASTERS/GLIDES
CENTER HOLE
OF SEAT
LEVER
CONTROL
PADDLE
FIGURE 2.
8
9
CSO-04

Logo/Company Name
4”w x .75”h
Assembly Instructions
1) Remove the two bolts from the (1) arm.
2) Align the open slot of the (2) arm cup
so that it is even with the bottom of the
cylinder of (1) arm.
3) With the (3) seat upside down, align the slot
of the (2) arm cup with the (6) mounting
bracket. Attach with the two bolts. (Note:
Make sure that the (5) button is facing
away from the (3) seat.) Repeat steps for
opposite side.
4) You can adjust the arms in and out by
loosening (4) lever and sliding the arm in
or out. When adjusted to desired location,
tighten (4) lever.
5) You can adjust the arms up or down by
pulling up on (5) button, adjust to desired
height and then release (5) button.
6
2
1
4
3
5
CSO-07

Logo/Company Name
4”w x .75”h
Assembly Instructions
1) Remove base, pneumatic cylinder, seat, foot
ring (if included) and caster/glides from box.
2) Place base (1) upside down and insert
casters/glides (5) (see gure 1).
3) Slide optional foot ring (4) over pneumatic
cylinder from bottom (2) about halfway up
the cylinder and tighten knob (7).
4) Flip the base so casters/glides are on the
oor and insert pneumatic cylinder (2) as
shown in (gure 2) into center hole of base
with colored button up. Lightly push down.
Adjust foot ring to desired height
5) Align the center hole of the underside of
the seat assembly (3) with the top of the
pneumatic cylinder (2) and lightly push down.
With the weight of your body carefully sit on
the seat. This will press the base, pneumatic
cylinder, and seat together.
6) To raise the height of your stool, take your
weight off of the stool and pull on the ring on
the underside of the seat and adjust.
7) To lower the height of your stool you must be
seated with your weight on the seat - lift up
on the ring.
FIGURE 2.
CASTERS/GLIDES
BASE 1
3
CASTERS
CSO-01

Oxford Series Assembly Instructions
3
CASTERS/GLIDES
2
1
4
6
5
7
ARM
S
8
1) Remove base, back, pneumatic cylinder,
casters/glides, and seat from box.
2) Insert casters/glides 2on base 1. Using
pressure, push the casters/glides into the
base making sure they are all the way in.
3) Place base 1with legs on hard level surface.
4) Insert cylinder 3into center hole of base and
lightly push down.
5) (Optional) Arm rests 8are factory installed
for shipping. Use enclosed allen wrench to
adjust width of arms: loosen screw, adjust
arms, tighten screw.
6) Turn seat upside down and place on the
edge of a table to slide the back bar into
position.
7) Attach back bar to seat 4using 4 bolts
and 4 washers. Firmly tighten with enclosed
allen wrench.
8) Turn assembled seat over and align the
center hole on the bottom of the seat with
the top of the pneumatic cylinder and lightly
push down. With the weight of your body,
carefully sit on the seat. This will press the
base, pneumatic cylinder, and seat together.

Windrowe Series Assembly Instructions
3
CASTERS/GLIDES
2
1
4
6
5
7
ARMS
8
HEAD
REST
9
P
ADDLE
10
1) Remove base, back, pneumatic cylinder,
casters/glides, and seat from box.
2) Insert casters/glides 2on base 1. Using
pressure, push the casters/glides into the
base making sure they are all the way in.
3) Place base 1with legs on hard level surface.
4) Insert cylinder 3into center hole of base and
lightly push down.
5) (Optional) Arm rests 8are factory installed
for shipping. Use enclosed allen wrench to
adjust width of arms: loosen screw, adjust
arms, tighten screw.
6) Turn seat upside down and place on the
edge of a table to slide the back bar into
position.
7) Attach back bar to seat 4using 3 bolts
and 3 washers. Firmly tighten with enclosed
allen wrench.
8) (Optional) Attach headrest 9to top of seat
back 7and using enclosed allen wrench,
insert and tighten 2 screws to back.
9) Turn assembled seat over and align the
center hole on the bottom of the seat with
the top of the pneumatic cylinder and lightly
push down. With the weight of your body,
carefully sit on the seat. This will press the
base, pneumatic cylinder, and seat together.