Stanley Omnilock 45HOM User manual

Toensureaccuratedoorpreparation,useonlyfactory-printedtemplates.Donotusecopiesorfacsimiles. T83316/RevB– 0000 000 ER-7991-42 Aug2016
STANLEY OMNILOCK
snoitcnuF
VD VT
llirdotseloH
S/I S/O S/OS/I
ArednilyC
BnrutbmuhT
CreveL
†
hguorhT
rood
hguorhT
rood
DgnitnuommirT
†
hguorhT
rood
hguorhT
rood
EgnidnuorG
F)seloh2(tlobeludoM hguorhT
rood
hguorhT
rood
G
HgnitnuomnrutbmuhT
wercs
GraelcffodnatS ecna
JrooD
egdE
hctiwSsutatSrooD
)lanoitpO(
Installation Template for 45HOM Mortise Locks
—7/2009 OM1 B
2 3/4” ”4/31MOH54
Holes by Function
A
B
C/D
F
G
H
1
11
/ 16 in
(43 mm)
3
5
/ 8 in
(92 mm)
1
/ 2 in
(13 mm)
1
/ 2 in
(13 mm)
2
27
/ 64 in
(62 mm)
1
29
/ 64 in
(37 mm)
1
29
/ 64 in
(37 mm)
1
1
/ 8 in
(29 mm)
7
/ 8 in
(22 mm)
5
1
/ 4 in
(133 mm)
2
12
/in
(64 mm)
~35
o
3
/ 8 in
(10 mm)
1
3
/ 4 in
(44 mm)
1in
(25 mm)
1 / in 4
32 mm
1
3
/ 8 in
(10 mm)
F/G
EH
D
D
H
Optional for
Wireless TV
J
F/G
Deadbolt Models
Select, mark and
drill holes
1 Refer to the Holes by Function table
and the gure below to determine
the holes to be drilled for the lock
function and trim combination.
2 Determine the inside and outside,
hand, and bevel of the door.
3 Position one of the door edge
templates on the door, making
sure that the lock case mortise
shown on the template aligns with
the mortise pocket prepared in the
door. Tape the template to the
door.
4 Using the centerlines on the door
edge template as a guide, position
the appropriate door template on
each side of the door. If the door is
beveled, you need to take the bevel
into account. Tape the templates
to the door.
5 Center punch the appropriate drill
points.
6 Drill the holes. See the Installation
Instructions for 45HOM Mortise
Locks.
†Because these holes pass through the mortise
pocket, it is recommended that each hole be drilled separately rather than straight through. For Extreme Weatherized models see Addendum for Stanley Omnilock 45HOM ExtremeWeatherized Locks (T83317), which includes a template for mounting the extreme
weatherized model.
Title
Series Backset Trim style Door thickness Rev date Template
number
Rev
4 in
(101.6 mm)
C
L
2
3
/ 4 in
(69.85 mm)
C
L
A

Note :If smoke seal, weatherstripping, acoustical material, or silencers
are used on the door frame, care must be taken so that they will not
interfere with the ease in which the latchbolt enters the strike.
Hole Descriptions
ACylinder (1)
BThumb turn (1)
CLever (1)
D Trim mounting (2)
EGrounding (1)
FModule bolt (2)
GStandoclearance(2)
HThumb turn mount-
ing screw (2)
7/8 in
23 mm
D
1/8 in
3 mm
1/2 in
13 mm
B
C
Strike lip
Horizontal centerline
of lock
1 1/4 in
32 mm
Horizontal centerline
of lever
5/16 in
8 mm
5/16 in
8 mm
3/16 in
5 mm
A
Through hole
Outside only
5/16 in
8 mm Outside only
Through hole
1/2 in
13 mm
Vertical centerline
of lever
3/8 in
10 mm
To ensure accurate door preparation, use only factory-
printed templates. Do not use copies or facsimiles.
Strike lip
1/8 in
3 mm
Horizontal centerline
of lock
A
1 1/4 in
32 mm
Hole Descriptions
ACylinder (1)
BThumb turn (1)
CLever (1)
DTrim mounting (2)
EGrounding (1)
FModule bolt (2)
GStando clearance (2)
H Thumbturnmounting
screw (2)
Horizontal centerline
of lever
5/16 in
8 mm
7/8 in
23 mm
3/8 in
10 mm
1/2 in
13 mm
3/16 in
5 mm
5/16 in
8 mm
5/16 in
8 mm
Through hole
Outside only Outside only
F
3/16 in
5 mm
G
Through hole
1/2 in
13 mm
E
C
Vertical centerline
of lever
B
3/8 in
10 mm
D
Vertical
centerline
of lock
Strike lip
Horizontal centerline
of lever
Horizontal centerline
of lock
1 1/8 in
29 mm
Strike lip
Horizontal centerline
of lock
Horizontal centerline
of lever
H
E
3/8 in
10 mm
D
H
Lock case mortise
1 1/8 in
29 mm
Lock case mortise
Vertical
centerline
of lock
Align to edge of door.
Note :Use this template for the inside
of a LH or LHRB door or the outside
(keyed side) of a RH or RHRB door.
Note :Use this template for the inside
of a RH or RHRB door or the outside
(keyed side) of a LH or LHRB door.
Detach here
Detach here
Align to edge of door.
Low bevel edge
(narrow side)
Flat edge
(no bevel)
High bevel edge
(wide side)
Low bevel edge
(narrow side)
Flat edge
(no bevel)
High bevel edge
(wide side)
F
D
G
F
F3/16 in
5 mm
G G
Detach here
4 in
101.6 mm
4 in
101.6 mm
69.85 mm
2 3/4 in
69.85 mm
2 3/4 in
1 1/4 in
32 mm
1 1/4 in
32 mm