Steelcase Ology User manual

If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2020 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
WARNING
Pinch points. Keep Clear.
Risk of Serious Injury.
Moving worksurfaces can pinch and
cause injury or property damage.
Keep height-adjustment range free from
obstructions above and below the worksurface.
Keep a minimum 1” gap to adjacent furniture,
wall or panel.
1.
2.
2
1
3
Ology or Migration SE Desk to Universal Steel Storage
Not for use by children.
3.
English - Pages 1 to 13 of 39
French - Pages 14 to 26 of 39
Spanish - Pages 27 to 39 of 39
74785 Rev C
#2 SQUARE BIT

®
Page 2 of 39
74785 Rev C
UNDERSIDE OF DESK
WIRE MANAGER
WIRE MANAGER
TAPPING SCREW
TRH, SERR, 10-12 X .625
Leveling and Adjusting
Caster Height
1. Level desk in final location.
2. Attach wire manager to
cantilever on the underside of the
desk.
OLOGY
MIGRATION SE
WIRE MANAGER
2
GAUGE HERE

®
3. Place grommet in cutout in top.
Clips will engage the bottom of the
top (3a).
Flip unit onto a protected surface
bottom side up. Secure grommet to
cutout using two (2) Tapping
Screws, TRH, SERR, 10-12 x .625
provided in kit (3b).
3a
3b BOTTOM SIDE
OF TOP
TOP
OF TOP
TOP OF TOP
CLIP
BOTTOM SIDE
OF TOP
GROMMET
TAPPING SCREW -
TRH, SERR, 10-12 X .625
Page 3 of 39
74785 Rev C

®
Page 4 of 39
74785 Rev C
4a. Remove four shelf screws and shelf,
if present.
NOTE: Shelf screws are for shipping
only and should not be reinstalled.
4b. Remove inner back by pulling top
corners to release hook and loop
fasteners.
INNER BACK
4a
4b

®
Page 5 of 39
74785 Rev C
Flush end of top to end of unit.
Proud top (18-7/8” deep) offset from
front edge of top by 7/8”.
Flush tops (18” deep) are aligned to
5b
5a
TAPPING SCREW -
TRH, SERR, 10-12 X .625
BOTTOM SIDE
OF TOP
PROUD TOP
(18 - 7/8” DEEP)
OFFSET FROM FRONT
EDGE OF TOP BY 7/8”
FRONT EDGE OF TOP
5a.
5b.
the front of the unit. Secure unit to bottom
side of top by installing (5) Tapping
Screws, TRH, SERR, 10-12 x .625
provided installation kit.

®
6. Filler (optional) installation is unhanded. Align flush to
storage unit and edge of top (6a). Secure side of filler to side of
unit using two (2) Tapping Screws, Truss HD, 8-18 X .375
(6b). Secure bottom of filler to bottom side of top using two
(2) Tapping Screws, TRH, SERR, 10-12 X .625 provided in
installation kit (6c).
Note: If filler is used in a open condition on a common top,
make sure the panel is parallel to the end of the storage
unit.
6a
BOTTOM SIDE
OF TOP
TAPPING SCREW -
TRH, SERR, 10-12 X .625
FILLER 6c
6b
TAPPING SCREW -
TRUSS HD, 8-18 X .375
Page 6 of 39
74785 Rev C
For wire pass through: Insert flat-bladed
screwdriver in holes provided to break tab
on each side. Bend tab inward until the
flange hits the inside of the filler panel.

®
7. Flip unit over. Slide leg into
grommet and center side to side in opening.
8. Install leg retaining bracket
using four (4) Tapping Screws, TRH,
8 - 18 x .250 provided in
installation kit.
GROMMET
LEG
7
8
TAPPING SCREW -
TRUSS HD, 8-18 X .250
LEG RETAINING BRACKET
Page 7 of 39
74785 Rev C

®
9. Base brackets need to be broken apart before they can be installed.
Bend at parting line to separate (9a). Install base brackets as shown with four (4)
Tapping Screws, Truss Head, 8-18 X .250 provided in kit (9b).
9a
9b
BASE BRACKET
BASE
BRACKET
TAPPING SCREW -
TRUSS HEAD, 8-18 X .250 Page 8 of 39
74785 Rev C
OLOGY DESK ONLY

®
10. Attach base brackets to storage using pilot holes
provided.
NOTE: Brackets must be 1” from ends of legs
(see figure 10).
Page 9 of 39
74785 Rev C
BASE
BRACKET
TAPPING SCREW -
TRUSS HEAD, 8-18 X .250
MIGRATION SE ONLY
10
1”
BOTH ENDS

®
11. Level case by adjusting glides.
12. Connect wire manager to
case using wire tie in kit.
IMPORTANT:
Insert wire tie through holes in case
Page 10 of 39
74785 Rev C
then through connection between
the first link and second.
13. Run worksurface up
& down to make sure
the wire manager
runs smoothly.
11
12
GLIDE
WIRE MANAGER
CASE
WIRE TIE
4.25”
5.50”