Steelcase media:scape mini User manual

media:scape®mini and mobile -
Puck Replacement & Power Switch
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2011 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 7
939501567 Rev A
1/16” ALLEN WRENCH
STRONG MAGNET
media:scape®mini media:scape®mobile

Page 2 of 7
939501567 Rev A
®
Note: Pages 2 through 6 describe a
media:scape mini unit. Refer to page 7 for
the differences if your unit is a media:scape
mobile.
1. Remove the television from the unit (depress
dislodgement tabs on mounting brackets).
2. Remove the shroud from the unit. (depress
dislodgement tabs on unit).
To remove shroud, locate
anti-dislodgement clips on
each side. Press them towards
the monitor and lift up & out.
To remove monitor, locate
anti-dislodgement clips on
each side. Press them
towards the monitor, lift
monitor up & out.
2
1

Page 3 of 7
939501567 Rev A
®
3. Remove the puck connectors and/or the
power on connection from the switcher. (use
small flat head screwdriver).
(4) PUCK CONNECTORS
(1) POWER CONNECTOR
3

Page 4 of 7
939501567 Rev A
®
4. Rotate the unit so that you have access to
the bottom (two persons required).
5. Remove the plastic base cover with a Phillips
screwdriver.
6. Remove the media:well from the unit by
removing (4) screws (Phillips screwdriver).
PLASTIC COVER
4
Remove (6) screws 5Remove (4) screws that hold
the media:well onto the steel
bridge and plastic base.
6

Page 5 of 7
939501567 Rev A
®
7. a) Remove (6) screws from the
media:well, then b) remove the bezel.
NOTE: If you are replacing the
power-on button, proceed to step 8.
If not, go right to step 11.
8. Remove the power-on button by
removing (2) screws from the bezel with
a 1/16” allen wrench.
9. Remove the power button cables
from the base, then reroute the new
power-on cable.
10. Attach the new power-on button
with (2) screws, then reroute the cords.
11. If a puck needs to be replaced, start
by removing the flocking liner inside the
media:well with a strong magnet.
8Use a 1/16”
allen wrench
7a
7b
PUCKS
MAGNET
FLOCKING
PLATES

Page 6 of 7
939501567 Rev A
®
12. Remove electrical enclosure by removing
(4) screws.
13. Remove puck that is intended for
replacement. Route the replacement puck cord.
14. When assembling the new puck, the
grommet should be 42” from the end of the cord.
15. Assemble electrical enclosure with the 4
screws that were removed in step 12.
16. Place the flocking liners back into the
media:well.
17. Screw the bezel onto the media:well using
(6) screws.
18. Attach the media:well to the bridge and
plastic base with (4) screws.
19. Assemble the base cover to the base with
(6) screws.
20. Rotate the unit upright (2 people).
21. Attach all cords to the switcher.
22. Put shroud and TV back on.
12 Remove (2) screws
each side.
ELECTRICAL
ENCLOSURE
48”
(1219 mm)
14

Page 7 of 7
939501567 Rev A
®
Note: This page shows the differences
between a media:scape mobile and a
media:scape mini unit. Follow the
procedures described on pages 2
through 6 except the following:
A) Steps 4 and 5 not needed. Remove flocking
plate with a strong magnet.
B) Remove the media:well from the bridge and
plastic trim cover by removing (2) screws.
C) Remove (2) screws (one each side) at top of
plastic trim cover so cover can fully be removed
(Phillips).
D) Remove cord clamp that houses puck and
power- on cables (Phillips).
E) Follow step 7 on from the mini process.
media:scape®mobile
MAGNET
FLOCKING
PLATES A
B
Remove (2) screws
D
CORD CLAMP
TRIM COVER
C
REAR VIEW