Steelcase Opus User manual

Opus™ Adjustable Corner Trim Unit
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2014 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 12
939500290 Rev C

Page 2 of 12
939500290 Rev C
NOTE: Determine which base unit will
have the side panel attached.
1. Turn base assembly on it's side.
Lower the end panel onto the base
assembly as shown (1a). Make
sure there is a 1/8" offset at the top
of the base assembly and make sure
the front of the end panel is 3/4" from
the front of the canopy (1b). The
bottom of the end panel will be flush
with the top of the base.
2. Secure the end panel to the base
assembly by first squaring up the top
of the panel to the top of the base
assembly and installing three (3)
1-1/4" wood screws (2a).
NOTE: When squaring up top of panel
to top of assembly, be mindful of the
1/8" offset discussed in step 1.
Square up the back of the end panel
to the back edge of the base assembly
and install the five (5) remaining 1-1/4"
screws (2b).
2b
2a
1b
1a
INSTALL THESE FIVE (5)
1-1/4" WOOD SCREWS
ONE AT A TIME
BY FIRST SQUARING
UP BACK OF PANEL TO
BACK OF ASSEMBLY
INSTALL THESE THREE (3)
1-1/4" WOOD SCREWS
FIRST AFTER SQUARING
UP TOP OF PANEL TO
TOP OF ASSEMBLY
19-5/16"
REF.
END PANEL
3.4” 1/8” OFFSET

Page 3 of 12
939500290 Rev C
3. Align gussets at end of toeboard
(3a) and secure using four (4) 5/8"
wood screws (3b). Align toeboard
with toeboard side and gussets (3c).
Attach toeboard with four (4) 5/8"
wood screws though gussets and
into toeboard (3d).
4. Align toeboard face flush with
base as shown (4a) and attach using
three (3) 1-1/4" wood screws (4b).
3a
4a
4b
3b
3d
3c
FLUSH
FLUSH
THREE (3) 1-1/4"
WOOD SCREWS
GUSSETS
TOEBOARD
SIDE
TOEBOARD
FOUR (4) 5/8"
WOOD SCREWS
FOUR (4) 5/8"
WOOD SCREWS

Page 4 of 12
939500290 Rev C
5. Push base unit into
place.
6. Level base unit.
7. Secure units together
and place in position
against wall. Refer to
assembly direction
#939500801.
8. Install storage cabinet.
Refer to assembly
direction #939500811.
5
6
BASE
UNIT

Page 5 of 12
939500290 Rev C
9. Secure end panel to lower storage
cabinet using two (2) 1-1/4" wood
screws.
10. Insert (5) shoulder screws into
the holes on the filler panel.
9
10
TWO (2) 1-1/4"
WOOD SCREWS
SHOULDER
SCREWS
FILLER
PANEL

Page 6 of 12
939500290 Rev C
11. Align filler panel with
end panel (11a) and insert
the shoulder screws into
the modeeze clips (11b)
located on the front of the
end panel. Push the panel
downward (11c), until
shoulder screw is securely
seated (11d).
11a
11b
11c
11d

Page 7 of 12
939500290 Rev C
12. Turn the other base
assembly on it's side. Lower
the end panel onto the base
assembly as shown (12a).
Make sure the top of the
base assembly and the top
of the end panel is flush
(12b), also make sure the
side of the end panel is flush
with the front of the canopy
assembly and square to the
base unit upright (12c).
13. Secure the end panel to
the base assembly by first
squaring up the top of panel
to the top of the assembly
and installing three (3)1-1/4"
wood screws (13a).
Square up the back of the
end panel to the back edge
of the base assembly and
install the six (6) remaining
1-1/4" screws (13b).
14. Install three (3) shelf
support pins into the end
panel.
14
12a
12b 12c
13a
13b
INSTALL THESE (6)
1-1/4" WOOD SCREWS
ONE AT A TIME
BY FIRST SQUARING
UP BACK OF PANEL TO
BACK OF ASSEMBLY
INSTALL THESE (3)
1-1/4" WOOD SCREWS
FIRST AFTER SQUARING
UP TOP OF PANEL TO
TOP OF ASSEMBLY
FLUSH FLUSH
END PANEL
20-3/32"
REF.

Page 8 of 12
939500290 Rev C
15. Slide units together. Secure units together
and place in position against wall. Refer to
assembly direction #939500801.
16. Install storage cabinet. Refer to assembly
direction #939500811.
17. Secure end panel to lower storage cabinet using
two (2) 1-1/4" wood screws.
15
17
TWO (2) 1-1/4"
WOOD SCREWS

Page 9 of 12
939500290 Rev C
18. Slide the two units next to adjoining assembly
(18a). Level base unit (18b). Attach using one (1)
wood screw as shown (18c).
18b
18a
18c

Page 10 of 12
939500290 Rev C
19. Determine a level line on corner wall and mark with
pencil (19a). Attach dust cover attachment support using
two (2) screws (19b).
19a
19b
DUST COVER
ATTACHMENT
SUPPORT