SteelFlex CEO-200 User manual

OWNER'S MANUAL
CEO-200
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:
1.Inspect equipment before each workout. Check that all nuts, bolts, screws and
pop pins are in place and fully tightened. Also, before use, check cylinders for leaking.
Replace all worn parts immediately. Never use machine if any parts are
damaged or missing. Fallure to follow these rules may result in serious injury.
2.Keep clear of the cylinder and all moving parts when the machine is in use.
3.Exercise with care. Perform your exercises at a smooth moderate pace; never
perform jerky or uncoordinated movements that may cause injury.
4.It is recommended that you should workout with a training partner.
5.Do not allow children or minors to play on or around this equipment.
6.If unsure of proper use of equipment, call your local distributor.
7.WARNING: Consult your physician before starting your exercise program. For your
own safety do not begin any exercise program without proper instruction.
The Surgeon General
has determined that lack
of physical activity is
detrimental to your health.TM
Trademark of United States Fitness Produots Council
All manuals and user guides at all-guides.com
all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
HARDWARE ILLUSTRATION
1.1
(A2)ROUND INNER HEX SCREW M8X40L PARTIAL QTY.4
CEO200-032008
2
13456
(A4)BOLT CAP(9212-024) QTY.8
(A1)ROUND INNER HEX SCREW M8X45L PARTIAL QTY.2
(A3)HEX BOLT M12X130L PARTIAL QTY.4
(A5)M10X25L SOCKER FLAT SCREW QTY.1
All manuals and user guides at all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
HARDWARE ILLUSTRATION
1.2
(B1) M8 NYLON LOCK NUT QTY.2
CEO200-032008
(B2)M10 NYLON LOCK NUT QTY.2
2
13456
(C1)M8(I.D.)FLAT WASHER Ø24 QTY.4
(C2)M10(I.D.)FLAT WASHER Ø27 QTY.2
(C3)1/2" ROUND END CAP WASHER QTY.8
(C4)M10 SPRING WASHER QTY.2
(B2)M12 NYLON LOCK NUT QTY.4
All manuals and user guides at all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
HARDWARE ILLUSTRATION
2CEO200-032008
D1. D2.
D6.
(D1)Ø50X10 END COVER(8130-131)
(D2)CU WASHER(8520-008)
(D3)50X75 FLAT END CAP(9211-012)
(D4)50X100 FLAT END CAP(9211-014)
(D5)Ø64 PULLEY(9213-023)
(D6)Ø60X42H DECK BUFFER(9214-037)
------------------------------------------[1PCS]
-----------------------------------------------------[1PCS]
------------------------------------------[2PCS]
-----------------------------------------[2PCS]
-----------------------------------------------------[2PCS]
-------------------------------------[4PCS]
D3. D4.
D5.
All manuals and user guides at all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
3CEO200-032008
PARTS ILLUSTRATION SHEET
A[1SET] B[1SET] C[1SET]
D[1PCS]
9710-020 E[2PCS] 8830-020 F[2PCS] 8312-091
50
170
130
All manuals and user guides at all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
4CEO200-032008
Above shows STEP1
assembled and completed
D4
D6
D6 D4
A4X4
A3X4
C3X4
FX2
B
A
C3X2
A4X2
B2X2
C3X2
B2X2
A4X2
D3
D6
D6
D3
All manuals and user guides at all-guides.com
all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
5
CEO200-032008
Above shows STEP2
assembled and completed
D
A2X4
A1
C1
D5
B1 C1
C1
B1
A1 C1
D5
All manuals and user guides at all-guides.com

ASSEMBLY INSTRUCTIONS
Page
CEO-200
6CEO200-032008
Above shows STEP3
assembled and completed
C1
B2
C2
D2
B2
C2
E
E
M8 WASHER Ø24 X2
M8 SPRING WASHER X2
M8X35L ROUND INNER HEX SCREW X2
C4
C4
A5
All manuals and user guides at all-guides.com

Page
450
n8.3
n8
Cylinder Description and Assembly Instruction
※This model of cylinder contains a spring inside so it can not be pulled out by hand directly.
Part No.8830-016
Adapt Model: CLP-600
※This cylinder does not contain a spring, and it can be pulled out directly by hand.
Part No. 8830-017
Adapt Model: CBP300、CLE500、CAC700、CSP900、CAB1000
450
n8
n8
424
424
03-2008
All manuals and user guides at all-guides.com

A-A
Page
A
A
339 n8
n16.4
※This cylinder does not contain a spring, and it can be pulled out directly by hand.
※No attached iron bush Ø16X Ø8X22.5L
Part No. 8830-020
Adapt Model: CEO-200, CPD-800
※This cylinder does not contain a spring, and it can be pulled out directly by hand.
※With attached iron bush ODØ16X IDØ8X22.5L
Part No. 8830-020
Adapt Model: CBC-400, CTH-1100
Assembled
339
n8n8
Nylon Cushion
Assembled
Iron Bush
Nylon Cushion
Nylon Cushion
Nylon Cushion
n8
n16
22.5
16.4
Ø
22.2
Ø
2.6
9.9
Cylinder Description and Assembly Instruction
03-2008
All manuals and user guides at all-guides.com