SteelFlex CSP-900 User manual

OWNER'S MANUAL
CSP-900
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:
1.Inspect equipment before each workout. Check that all nuts, bolts, screws and
pop pins are in place and fully tightened. Also, before use, check cylinders for leaking.
Replace all worn parts immediately. Never use machine if any parts are
damaged or missing. Fallure to follow these rules may result in serious injury.
2.Keep clear of the cylinder and all moving parts when the machine is in use.
3.Exercise with care. Perform your exercises at a smooth moderate pace; never
perform jerky or uncoordinated movements that may cause injury.
4.It is recommended that you should workout with a training partner.
5.Do not allow children or minors to play on or around this equipment.
6.If unsure of proper use of equipment, call your local distributor.
7.WARNING: Consult your physician before starting your exercise program. For your
own safety do not begin any exercise program without proper instruction.
The Surgeon General
has determined that lack
of physical activity is
detrimental to your health.TM
Trademark of United States Fitness Produots Council

ASSEMBLY INSTRUCTIONS
Page
CSP-900
HARDWARE ILLUSTRATION
1.1
(A1)ROUND INNER HEX SCREW M8X40L PARTIAL QTY.2
CSP900-032008
(A2)HEX BOLT M8X60L PARTIAL QTY.4
(A3)HEX BOLT M10X60L PARTIAL QTY.4
2
13456
(A4)BOLT CAP(9212-024) QTY.4
(A5)M10X25L SOCKER FLAT SCREW QTY.2

ASSEMBLY INSTRUCTIONS
Page
CSP-900
HARDWARE ILLUSTRATION
1.2
(B1) M8 NYLON LOCK NUT QTY.2
CSP900-032008
(B2)M10 NYLON LOCK NUT QTY.4
(C1)M8(I.D.)FLAT WASHER Ø18 QTY.4
2
13456
(C2)M8(I.D.)FLAT WASHER Ø24 QTY.4
(C3)M10(I.D.)FLAT WASHER Ø27 QTY.4
(C4)3/8" ROUND END CAP WASHER QTY.4
(C5)M8 SPRING WASHER QTY.4

ASSEMBLY INSTRUCTIONS
Page
CSP-900
HARDWARE ILLUSTRATION
2CSP900-032008
D1. D2. D3. D4.
D5. D6. D7.
(D1)Ø50X10 END COVER(8130-131)
(D2)40X80 END CAP(9211-113)
(D3)Ø60X42H DECK BUFFER(9214-037)
(D4)40X80 ROUND END COVER(9261-070)
(D5)40X80 FOOT CAP(9261-071)
(D6)40X80 FOOT CAP(9261-072)
(D7)95X140L RUBBER PAD(9630-003)
-------------------------------------------[2PCS]
-------------------------------------------------[2PCS]
--------------------------------------[2PCS]
----------------------------------[2PCS]
------------------------------------------------[1PCS]
------------------------------------------------[1PCS]
---------------------------------------[2PCS]

ASSEMBLY INSTRUCTIONS
Page
CSP-900
3CSP900-032008
PARTS ILLUSTRATION SHEET
A[1SET] B[1SET] C[1PCS]
5584-K007 40X80X2tX600L
D[1PCS]
5584-K008 40X80X2tX600L E[1SET] 8220-148 Ø25.4X73.5L F[2PCS] 8386-101
G[1PCS]
8830-017 H[1PCS] 9121-064 I[1PCS] 9111-065

ASSEMBLY INSTRUCTIONS
Page
CSP-900
4CSP900-032008
Above shows STEP1
assembled and completed
D2
D4 A4X2
B2X2
C4X2
D4
D3
D3
F
C
A
D2
D7
D7
C3X2
A3X2
C3X2
A3X2
D5
D
D6
A4X2
B2X2
C4X2
F

ASSEMBLY INSTRUCTIONS
Page
CSP-900
5
CSP900-032008
Above shows STEP2
assembled and completed
E
B
B1 C1 C1 A1
D1
D1
A2X2
C5X2
C2X2
C1
A1
I
B1
C1
G
C2X2
C5X2
A2X2
A5
A5
H

Page
450
n8.3
n8
Cylinder Description and Assembly Instruction
※This model of cylinder contains a spring inside so it can not be pulled out by hand directly.
Part No.8830-016
Adapt Model: CLP-600
※This cylinder does not contain a spring, and it can be pulled out directly by hand.
Part No. 8830-017
Adapt Model: CBP300、CLE500、CAC700、CSP900、CAB1000
450
n8
n8
424
424
03-2008

A-A
Page
A
A
339 n8
n16.4
※This cylinder does not contain a spring, and it can be pulled out directly by hand.
※No attached iron bush Ø16X Ø8X22.5L
Part No. 8830-020
Adapt Model: CEO-200, CPD-800
※This cylinder does not contain a spring, and it can be pulled out directly by hand.
※With attached iron bush ODØ16X IDØ8X22.5L
Part No. 8830-020
Adapt Model: CBC-400, CTH-1100
Assembled
339
n8n8
Nylon Cushion
Assembled
Iron Bush
Nylon Cushion
Nylon Cushion
Nylon Cushion
n8
n16
22.5
16.4
Ø
22.2
Ø
2.6
9.9
Cylinder Description and Assembly Instruction
03-2008