SteelFlex CTH-1100.1 User manual

OWNER'S MANUALCTH-1100.1
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:
1.Inspect equipment before each workout. Check that all nuts, bolts, screws and
pop pins are in place and fully tightened. Also, before use, check cylinders for leaking.
Replace all worn parts immediately. Never use machine if any parts are
damaged or missing. Fallure to follow these rules may result in serious injury.
2.Keep clear of the cylinder and all moving parts when the machine is in use.
3.Exercise with care. Perform your exercises at a smooth moderate pace; never
perform jerky or uncoordinated movements that may cause injury.
4.It is recommended that you should workout with a training partner.
5.Do not allow children or minors to play on or around this equipment.
6.If unsure of proper use of equipment, call your local distributor.
7.WARNING: Consult your physician before starting your exercise program. For your
own safety do not begin any exercise program without proper instruction.
The Surgeon General
has determined that lack
of physical activity is
detrimental to your health.TM
Trademark of United States Fitness Produots Council

ASSEMBLY INSTRUCTIONS
Page
mm
inch
060
10 30 50
40
20 60 13012011010090 80
70 140 150
10
1" 6" 4"
3" 5"
2"
0
0
HARDWARE ILLUSTRATION
CTH-1100
(A4)HEX BOLT M10X60L PARTIAL THREAD QTY.4
CTH1100.1-092008 1.1
(A5)HEX BOLT M10X100L PARTIAL THREAD QTY.2
(A3)HEX BOLT M8X60L PARTIAL THREAD QTY.4
(A2)ROUND ALLEN HEAD M8x40L PARTIAL THREAD QTY.2
(A6)M10X25L SOCKER FLAT HEAD SCREW QTY.2
(A7)ROUND ALLEN HEAD M8x30L PARTIAL THREAD QTY.8

ASSEMBLY INSTRUCTIONS
Page
mm
inch
060
10 30 50
40
20 60 130120
110
10090
8070 140 150
10
1" 6"
4"
3" 5"
2"
0
0
CTH-1100
CTH110.1-082008 1.2
(C1)3/8" ROUDN END CAP WASHER QTY.4
(B1)NYLON LOCK NUT M8 QTY.2
(B2)NYLON LOCK NUT M10 QTY.6
(C2)M8 SPRING WASHER QTY.4
(C3)M8(I.D.)FLAT WASHER Ø18X1.5T QTY.4
(C4)M8(I.D.)FLAT WASHER Ø24X1.6T QTY.4
(C5)M10(I.D.)FLAT WASHER Ø19X1.5T QTY.4
HARDWARE ILLUSTRATION
(C7)1/2"(I.D.)FLAT WASHER Ø25X2T QTY.2
(C6)M10(I.D.)FLAT WASHER Ø27X1.6T QTY.4
(B4)NYLON LOCK NUT 1/2" QTY.2
(C8)1/2" SPRING WASHER QTY.2

ASSEMBLY INSTRUCTIONS
Page
mm
inch
060
10 30 50
40
20 60 130120
110
10090
8070 140 150
10
1" 6"
4"
3" 5"
2"
0
0
CTH-1100
CTH110.1-072008 1.3
(C8)1/2" BOLT CAP(9212-024) QTY.4
HARDWARE ILLUSTRATION

ASSEMBLY INSTRUCTIONS
Page
CTH-1100
CTH1100.1-072008 2
D1. n50X10 END COVER (8130-131)--------------------------------[2PCS]
D3
D4. 40X80 END CAP(9211-113)----------------------------------------[2PCS]
D6. n60X42H DECK BUFFER (9214-037)---------------------------[2PCS]
D7. 40X80 ROUND END COVER (9261-070)----------------------[2PCS]
D8. 40X80 FOOT CAP (9261-071)-------------------------------------[1PCS]
D9. 40X80 FOOT CAP (9261-072)--------------------------------------[1PCS]
D2D1 D4
HARDWARE ILLUSTRATION
D10. 95X140L RUBBER PAD(9630-003)------------------------------[2PCS]
D5 D6 D7 D8
D2. n1" CU WASHER(8520-008)---------------------------------------[2PCS]
D3. o50 ROUND END CAP (9211-087)-----------------------------[3PCS]
D9 D10
D5.RUBBER BOLT HEAD PROTECTOR 5/16"(9214-030)------[8PCS]
D13.Ø39.5X3TXØ20 RUBBER DOUNT(9310-068)-----------------[2PCS]
D13
D14.Ø16X22.5L STEEL BUSHING(8110-090)-----------------------[2PCS]
D14

ASSEMBLY INSTRUCTIONS
Page
PARTS ILLUSTRATION SHEET
CTH-1100
CTH1100.1-072008 3
A1[1PCS]
B1[1PCS] C1[1PCS]
F[2PCS]
G[1PCS]
Direction Direction
H[1PCS]
I[1PCS]
5584-K007
40X80X2TX600L
J[1PCS]
5584-K008
40X80X2TX600L
K[2PCS]
8386-101 L[1PCS]
8830-018
M[1PCS]
9111-065 N[1PCS] 9121-067 O[2PCS] 9131-022 R[2PCS] 9131-023
Nail Nail
S[1PCS]
8220-164
Ø20X260L
T[1PCS]

ASSEMBLY INSTRUCTIONS
Page
CTH-1100
CTH1100.1-072008 4
Above shows STEP 1
assembled and completed
D3
D4
D10
D10
D9
K
J
D8
A4
C6
x2
x2
D3
C6
A4
x2
x2
D6
D6 D7
I
K
C1
B2
C8
x2
x2
x2
D7
D4
A1
C1
B2
C8
x2
x2
x2

ASSEMBLY INSTRUCTIONS
Page
CTH-1100
CTH1100.1-082008 5
Above shows STEP 2
assembled and completed
D1
D2
C7
D2
C1
D1
C7 A6
F
A6
F
B1
C8
B4
C8
B4

ASSEMBLY INSTRUCTIONS
Page
CTH-1100
CTH1100.1-092008 6
Above shows STEP 3
assembled and completed
O
Rx8
x8
H
B2 C5
GC5 A5x2
x2
x2
x2
O
R
short
long
SHORT LONG
M10 WASHER Ø27
M10X20L HEX BOLT
D5
S
C3
B1
B1
C3
A2
C3
L
D14
D14 STEEL BUSHING
(8110-087)
STEEL BUSHING
(8110-087)
A2
C3
M8 WASHER Ø18
M8X40L RONUD BOLT
M8 WASHER Ø18
NYLON LOCK NUT M8
M10 WASHER Ø27
M10X20L HEX BOLT
T
M8X40L RONUD BOLT
M8 WASHER Ø18
M8 WASHER Ø18
NYLON LOCK NUT M8
D13
D13
* : Tighten the nylon locknut until it fixed,
and loosen it 1/4 circle in order to avoid too tight nylon locknut influencing the machine movement.
*
*
A7

ASSEMBLY INSTRUCTIONS
Page
CTH-1100
CTH1100.1-072008 7
Above shows STEP 4
assembled and completed
C4 C2 A3
C4 C2 A3
M
A3
C4
C2 x2
x2
x2
N