Stewart Filmscreen Cima Original instructions

PDF provided by Conference Room AV
Stewart Filmscreen 00900-1092H Cima 92" Fixed Frame Projection Screen (White) - 16:9 HDTV

TO THE INSTALLER: BE SURE TO LEAVE THIS MANUAL WITH THE OWNER.
To the Owner
Installation Instructions
Screen Care
Maintenance
Fixed Frame Screen
Owner’s Manual &
Installation Instructions
CFS-0415

Wall mount (standard screen attachment)
Aperture mount
At the designated point in the installation, you will need to refer to the
general instructions for attaching the screen to the frame.
TO THE OWNER
Using this manual for installation
For the frame and mount type, refer to the appropriate page:
2
Congratulations on your purchase of one of our highly versatile Cima
projection screens representing "Top of the Class" in standard
commercial and residential projection screens.
Please take a moment to review this manual as it will help ensure you
many years of trouble-free service from your new Cima by Stewart
Filmscreen product.
This manual includes and describes proceduresfor several types of
frames and mounts. You must refer to the appropriate section for the
type of Cima Fixed Frame you are installing. In addition, there are
general instructions for attaching the screen to the frame that are
provided in a separate section. This procedure is to be performed at a
specific step in the overall sequence.
©2015 Stewart Filmscreen Corporation

To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Printed in U.S.A.
©2015 Stewart Filmscreen Corporation
www.stewartfilmscreen.com.
Stewart Filmscreen reserves the right to make changes to the product specified in this document.
Sizes and specifications subject to change without notice at Manufacturer's discretion. From time to time, this
document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at:
Contents
Assembling the Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mounting the Frame . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Attaching the Screen To Frame. . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting the Screen Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Attaching the back support to the frame (where required) . . . . 11
Screen Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Mounting the Frame - Section View . . . . . . . . . . . . . . . . . . . . . 7
General Notes for Preparing the Installation . . . . . . . . . . . . . . . 4
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Aperture Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
General Instructions For Attaching Screen To Frame . . . . . . . 8
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Preparation
Check the specifications for the type of frame and mounting to be
used.
You will need:
A level
Fasteners appropriate for the surface on which the screen is
being mounted (See instructions for the type of mount for
recommendations.)
Tools for tightening fasteners
Unpacking
Be sure to unpack carefully in a clean area. Use special care when
handling the screen so that it does not become soiled or damaged.
If you plan to repack your screen and hardware for transportation to another
location, you may wish to photograph or make a note of how it was packed.
Keep the packing material.
GENERAL NOTES FOR PREPARING THE INSTALLATION
Before proceeding with the installation of this screen,
take time to thoroughly read and understand these
installation and operation instructions.
Drill for making holes to attach brackets to the mounting surface,
as needed
Check the size and weight of the screen to be installed so that
you can plan for the number of people required for the mounting
procedure. You need at least two people to mount the smaller
screens; more are needed for larger, heavier screens.
Make sure there is a clean surface on which to unroll the screen
and assemble the frame.
Specifications regarding the individual screen dimensions, weight, and
mounting type are provided by the factory when the unit is ordered.
Before beginning the installation:
Note: Bolts and other fasteners for the screen are standard gauge and
sizes used in the U.S., regardless of where they will be installed. For this
reason, the sizes are expressed in inches rather than metric measurements.
©2015 Stewart Filmscreen Corporation
4
Ladders for the personnel supporting the screen during the
mounting process, as needed
Clean cotton gloves, for handling the screen

©2015 Stewart Filmscreen Corporation
Cima Fixed Frame Screen: Owner’s Manual

MOUNTING THE FRAME
Wall mount
1. Identify the location of wall studs where you can securely mount
the wall bracket.
2. Use a level to accurately position the wall bracket on the wall.
4. Drill holes in the wall through the bracket into the stud.
5. Use appropriate fasteners to secure the wall bracket to the wall
stud.
6. Check to make sure the bracket is level.
7. Hang the assembled frame, without the screen attached, on the
wall bracket to ensure that it is correctly mounted.
9. Reposition the frame, and slide the magnets so that they align
with the steel disks mounted on the wall.
10. Follow the steps for attaching the screen to the frame.
Holes drilled for wall mount
Hanging bracket
Follow the procedures for the type of mount you will use: wall mount or
aperture mount.
Figure 2: Wall bracket
©2015 Stewart Filmscreen Corporation
To accurately position the frame, you will mount the wall bracket and temporarily
attach the frame prior to attaching the screen fabric. Holes for supporting the
bracket are not pre-drilled; you can drill holes so that the frame mounting is
attached to wall studs. On the bottom of the frame, there are magnets you
canslide to align with wall studs; fasten the steel disks to the wall where studs
are located. If the wall is not perfectly flat, the force of the magnet may cause
the frame to bend. For this reason, wall puck shims (similar to washers) are
provided for you to place between thewall and the steel puck so that the frame
lays completely flat. The screen should not be attached to the frame at this
point. Refer to Figures 2,3,and 4.
8. Remove the frame. Drill holes so you can attach the steel disks
that will hold the magnets on the frame. Use wall puck shims as
needed.
6
3. Mark the desired position of the bracket on the wall. Mark the
location of the studs where you willdrill to attach the bracket.
Mark where you will attach the steel disks to the magnets which
will fasten to the frame.

MOUNTING THE FRAME - SECTION VIEW
Figure 3:Components for wall mount Figure 4: Hang the frame on wall mount
©2015 Stewart Filmscreen Corporation
7
Cima Fixed Frame Screen: Owner’s Manual

Standard attachment
Keep in mind that this procedure applies to several types of frames, so
the appearance of your frame may be somewhat different than that
shown in the illustrations.
Unpacking and unrolling the screen
The viewing side of the projection screen is rolled to the inside to protect
the optical coating. The screen is rolled lengthwise.
Caution
Be careful not to touch or scratch the image surface
with fingernails.
Do not use any tools to fasten the screen to the frame.
Do not fold or crease the screen.
1. Remove the screen
from the cardboard
shipping tube.
2. On a clean floor,
unroll screen viewing
side up.
This section provides the general instructions for attaching the screen to
the frame. DO NOT perform this step UNTIL instructed to do so in the
section for the specific type of mount you are using.
GENERAL INSTRUCTIONS FOR ATTACHING SCREEN TO FRAME
Figure 10:Unrolling the screen
3. Allow the paper to
unroll between
screenback and the
floor. (This will keep
thescreen clean.)
Referto Figure 10.
8
©2015 Stewart Filmscreen Corporation

Attaching the screen to frame
The next step is to attach the screen to the frame.
1. Place the frame
over the screen.
Figure 11:Lifting frame to snap on screen; top corner first
2. While lifting the
frame with one
hand, snap the
screen into the
frame. Gently allow
the screen to
stretchonto the
snaps. Do not jerk
the material, as it
can rip. Refer to
Figure11. Attach
the snaps on the top
corners and top
horizontal first.
Figure 12:Attaching all top snaps first
3. Lift the frame to a
vertical position to
finish attaching the
sides and bottom
rows of the snaps.
Refer to Figure 12.
©2015 Stewart Filmscreen Corporation
9
Cima Fixed Frame Screen: Owner’s Manual

ADJUSTING THE SCREEN FABRIC
Figure 5: Tapping snaps to reduce screen puckers
2. Place the frame on
the pre-mounted
wallscrews.
Figure 6:Completed Cima Fixed Frame screen mounted on wall
1.If there are puckers
inthe screen, you can
use a screwdriver to
tap the snaps so that
the puckers are
removed. A
movement of 1/16” to
1/8” (1.6 mm to 3.2
mm) is usually
sufficient to eliminate
puckers. Refer to
Figure 5.
©2015 Stewart Filmscreen Corporation
10
Follow the procedures below to adjust the screen should there be any
wrinkles or puckers

©2015 Stewart Filmscreen Corporation
Cima Fixed Frame Screen: Owner’s Manual 11

The aperture mount allows you to install the screen into an opening in a
wall or wall unit.
APERTURE MOUNT
1. Prepare the aperture.
2. Assemble the frame.
as shown in the
section starting on
page 4.
5. Carefully insert the
frame (with the screen
already attached) into
the aperture. Take
care so that you do
not damage the
screen. Figure 8:Front view: frame, mounting brackets, and screen
3. Attach optional
aperture mounting
brackets, if used.
Refer to Figure 8.
6. Attach the mounting
brackets to the wall
with the appropriate
fastener. Refer to
Figure 9.
©2015 Stewart Filmscreen Corporation
Figure 9: Rear view:
frame, mounting brackets, and screen
4. Attach the screen.
Go to the section on
attaching the screen
to the frame on
pages 8 & 9,then
return to this section.
12

General maintenance
The surface of your screen is delicate. Special attention to these instructions
should be followed when cleaning.
A draftsman-style brush may be used to lightly whisk away any
loose dirt or dust particles. (This type of brush is usually available
at office supply stores.) Stewart Filmscreen has an optional
screen cleaning kit that contains the proper type of brush.
Contact your dealer if you would like to obtain this cleaning kit.
For tougher spots, use a solution of mild detergent and water.
Rub lightly using a sponge. Blot with a damp sponge to absorb
excess water. Residual water marks will evaporate within a few
minutes.
VeLuxTM covering
Use a lint roller to remove particles from the VeLux material.
Replacement parts and service
No user-serviceable parts are contained within the unit. Contact your dealer
or the factory if you require part replacement or service.
SCREEN CARE AND CLEANING
Caution
Do not use any other cleaning materials on the screen. Contact the factory
if you have questions about removing difficult spots.
Do not use chemicals or solvents to clean the fabric.
Use only commercially available, water-based de-greaser
A brush can be used to comb (lift) the nap of the VeLux material
to help eliminate depression marks.
©2015 Stewart Filmscreen Corporation
Cima Fixed Frame Screen: Owner’s Manual 13

TROUBLESHOOTING
Problem description
Probable cause Action to take
Dirt, fingerprints, marks, etc. on
screen surface.
Improper handling of screen.
Brush off or use a mild detergent
solution with clean rag or cotton swab.
With reasonable care, you may expect many years of trouble-free
use from your Cima projection screen.
©2015 Stewart Filmscreen Corporation
Refer to the following guidelines if you encounter a difficulty in the
operation of your Cima Fixed Frame. Should you have a problem
that is not addressed here, call Stewart Filmscreen.
14

LIMITED ONE YEAR WARRANTY
STEWART FILMSCREEN CORPORATION (Stewart) warrants its Cima by Stewart Filmscreen products to the
original purchaser only, to be free from defects in materials and workmanship for a period of one
(1) year from the date of purchase by the original purchaser or eighteen (18) months from date of manu-
to Stewart instructions and are not damaged due to improper handling or treatment after shipment from
the factory. This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental
damage, including neglect caused by improper installation (i.e. proximity to hot lights, exposure to ex-
treme heat or cold, exposure to excessive humidity, etc.). Stewart on-site warranty repair services are not
available for this product
Stewart’s sole obligation under this warranty shall be to repair or to replace (at Stewart’s sole discretion)
the defective part of the merchandise. This warranty expressly does not cover any costs of removal, in-
stallation, framing, or other costs incident to replacing the screen or returning it to Stewart. Returns for
service should be made to your Stewart dealer. If it is necessary for the dealer to return the screen or part
to Stewart, transportation (freight) expenses to and from Stewart are payable by the purchaser. Stewart is
not responsible for damage in shipment. To protect yourself against damage or loss in transit, insure the
product and prepay all transportation expenses.
mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
will Stewart be liable for sums in excess of the purchase price of the product. No liability is assumed by
Stewart for expenses or damages resulting from interruption in operation of equipment, or for incidental,
direct, or consequential damages of any nature.
In the event that there is a defect in materials or workmanship of a Cima by Stewart Filmscreen,
you may contact our Customer Service Department at 1161W Sepulveda Blvd, Torrance, California 90502-
2797 (310-784-5300) Toll free (800-762-4999).
IMPORTANT: This warranty shall not be valid and Stewart shall not be bound by this warranty if the prod-
uct is not operated and maintained in accordance with Stewart’s written instructions.
Stewart Filmscreen Corporation shall not be liable for any and all consequential damage(s) occasioned
by the breach of any written or implied warranty pertaining to the sale of Cima by Stewart Filmscreen
product in excess of the purchase price of the product sold.
Printed in USA. Rev. 4/22/2015
resolution
15
©2015 Stewart Filmscreen Corporation

1-800-762-4999 Fax [phone]
www.stewartfilmscreen.com