Stewart Filmscreen RP-1013 User manual

Rigid Rear Projection Screens
Owner’s Manual
TO THEINSTALLER : BE SURE TO LEAVE THISMANUALWITH THE OWNER.
RP-1013
•TO THE OWNER
•INSTALLATION INSTRUCTIONS
•MAINTENANCE

Printed in U.S.A.
©2004–2013 Stewart Filmscreen Corporation
Stewart Filmscreen reserves the right to make changes to the product specied in this document.
From time to time, this document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at:
www.stewartlmscreen.com

Contents
To the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Frame Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Screen Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rigid Rear Projection Screens: Owner’s Manual 1
Rigid Rear Projection Screens
Owner’s Manual

Congratulations on your purchase of the finest optical viewing screen
available anywhere in the world!
To create Rigid Rear Projection Screens, Stewart Filmscreen fuses
advanced optical coatings to various glass and plastic substrates. This
provides optimized image fidelity for any viewing environment.
Please take a moment to review this manual; it will help ensure you many
years of trouble-free service from your new Stewart Filmscreen product.
Preparation
Specifications regarding the individual screen dimensions, weight, and
frame type are provided by the factory when the unit is ordered. Before
beginning the installation:
Check the specifications for the frame type. Ensure that the
aperture is the right size. (Refer to the section on frame types,
starting on page 5.)
Ensure that the area is prepared. In general, the screen should
be installed after electricians, painters, carpet-layers, and other
craftspeople have completed their work. This minimizes the risk
of damage to the optical surface.
Especially with large screens, ensure there is adequate access to
the installation area (e.g., door heights, width of hallways,
elevator capacity).
Check the size and weight of the screen to be installed so that
you can plan for the number of people and equipment required
for the installation.
You will need:
Clean gloves for handling the screen
Suction cups of the type typically used by glass and window
installers
A level
Appropriate fasteners (for installations that require them)
Appropriate tools for any fasteners used
Sufficient ladders, if required, for the personnel supporting the
screen during the installation.
A fork lift for very large or heavy screens
2Stewart Filmscreen Corporation
TO THE OWNER
Before proceeding with the installation of this screen, take
time to thoroughly read and understand these installation
and operation instructions.
PREPARING FOR INSTALLATION

Alternative installation
Stewart Filmscreen manufactures some very large, very heavy rigid screen
systems. Frequently the assistance and expertise of professional glaziers is
required to safely transport and install these screen and frame systems.
Take note of the scale and weight of your screen system and determine if
you should contract a glazing company for assistance.
Any screen exceeding 48" (122 cm) in height or 72" (183 cm) in width, or
having a total weight above 100 pounds (45 kg), should be considered
potentially challenging for typical installation crews, and your needs may be
better served by a professional glazier. We offer this recommendation with
the goal of protecting you, your personnel, the property, and the product.
Stewart Filmscreen offers factory supervision and installation feasibility
consultation on a fee basis and can manage your installation for you, upon
request.
If you have any questions, contact Stewart Filmscreen Corporation.
Rigid Rear Projection Screens: Owner’s Manual 3

Professional mounting techniques should be used. Stewart Filmscreen
Corporation cannot be liable for substandard or faulty installations.
General notes
The screen and frame are typically shipped as one complete unit. In some
instances, knocked-down, pre-drilled frame components and hardware are
shipped ready for assembly.
In some cases, no frame is supplied, as the screen is built in as part of the
installation.
Coated side
One side of the screen has a special optical coating. You will recognize
possible, the screen should
be installed with the coated side toward the audience. In this orientation,
the picture is more pleasing because there is no imaging of
lighted objects in the audience. Exceptions are:
Where the screen environment is uncontrolled and potential
abuse of the coating is a concern.
Screen marking pens are used during projection.
Unpacking and handling
Keep the screen protected until the environment is clean and
there is no danger of damage to the optical coating.
Open the crate as indicated, as this will expose the non-coated
side of the screen.
If the screen is already attached to the frame, do not lift the
screen by the upper frame member, as the frame may pull o the
screen, damaging the coating.
Use suction cups to remove and install the screen.
CAUTION: APPLY SUCTION CUPS ONLY ON THE NON-COATED SIDE OF THE SCREEN!
Keep hands and tools o the optical coating. Use cotton gloves
when installing the screen.
Installing the screen in the aperture
In general, the installation of a rigid rear projection screen is similar to the
process used when installing a window in a house. Use care when
handling the screen, especially the coated side, as mentioned above.
Once the screen is in place, make sure that it is level and plumb. Use
shims as needed.
4 Stewart Filmscreen Corporation
INSTALLATION








P1000, P1500, and P2000
The P1000 frame requires a wall opening 2 5/8” (6.668 cm) larger in both
height and width than the screen image size.
The P1500 frame requires a wall opening 3.5” (8.89 cm) larger in both
height and width than the screen image.
The P2000 frame requires a wall opening 4” (10.16 cm) larger In both
height and width than the screen image.
Rigid Rear Projection Screens: Owner’s Manual 5
FRAME TYPES
Figure 3. P2000
Figure 1. P1000
Figure 2. P1500

Deluxe frame
The Deluxe frame is 3 1/4” (8.255 cm) wide, with mitered corners and a
beveled edge. It can be set into a wall or cabinet. There are also free-
standing or suspended (flying) systems.
6Stewart Filmscreen Corporation
Figure 4. Deluxe frame
Figure 5. Cross section detail
of Deluxe frame; top
frame member
Figure 6. Cross section detail of
suspended Deluxe frame;
top frame member

Wedge frame
The wedge frame is used in video walls, simulators, and command and
control centers. The wedge profile tapers down on the image side to a knife
edge where it contacts the screen.
Multiple wedge frames can be installed in a containment frame.
Quick-Stall
The Quick-Stall frame allows for easy installation of a rigid rear screen by
eliminating the need for a finish trim. The Quick-Stall frame covers
unfinished molding with a built-in 5/8" (1.6 cm) trim.
The Quick-Stall frame requires a wall opening 5” (12.7 cm) larger in both
height and width than the screen image.
Rigid Rear Projection Screens: Owner’s Manual 7
Figure 9. Quick-Stall
Figure 7. Wedge frame Figure 8. Detail of two Wedge frames in a
partial containment frame

With reasonable care, you may expect many years of trouble-free use of
your Stewart projection screen.
We encourage you to keep your screen clean. Avoid getting any foreign
material on the screen, as cleaning may prove very difficult. It may not be
possible to remove scratches, paint, ink, etc.
General maintenance
The uncoated side of the screen requires only the care normally given to
glass or acrylic surfaces.
Pay special attention to these instructions when cleaning the surface with
the optical coating.
Use a draftsman-style brush to lightly whisk away any loose dirt
or dust particles. (This type of brush is usually available at office
supply stores.) Stewart Filmscreen has an optional screen
cleaning kit that contains the proper type of brush. Contact your
dealer if you would like to obtain this cleaning kit.
For tougher spots, use a solution of mild detergent and water.
Rub lightly using a sponge or clean cotton cloth. Do not use
aggressive or excessive pressure as the optical characteristics
could be degraded. Blot with a damp sponge to absorb excess
water. Any residual water marks or streaks will evaporate in a
few minutes.
Do not use any other cleaning materials on the screen, especially
chemicals, solvents, and abrasive cleansers. Contact the factory if you
have questions about removing difficult spots.
Replacement parts and service
No user-serviceable parts are contained within the unit. Contact your dealer
or the factory if you require part replacement or service.
8Stewart Filmscreen Corporation
SCREEN CARE AND CLEANING

LIMITED ONE (1) YEAR WARRANTY ON STEWART FILMSCREEN
CORP PROJECTION SCREENS SYSTEM
STEWART FILMSCREEN CORPORATION (Stewart) warrants its screens to
the original purchaser only, to be free from defects in materials and
workmanship for a period of one (1) year from the date of purchase by the
original purchaser or eighteen (18) months from date of manufacture, as
defined in the serial number, provided they are properly operated and
maintained according to Stewart instructions and are not damaged due to
improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse,
abuse, or accidental damage, including neglect caused by improper
installation (i.e. proximity to hot lights, exposure to extreme heat or cold,
exposure to excessive humidity, etc.) as well as product that have been
tampered with or repaired by any person or third party installation, other
than authorized Stewart personnel.
Stewart's sole obligation under this warranty shall be to repair or to replace
(at Stewart's sole discretion) the defective part of the merchandise. This
warranty expressly does not cover any costs of removal, installation,
framing, or other costs incident to replacing the screen or returning it to
Stewart. Returns for service should be made to your Stewart dealer. If it is
necessary for the dealer to return the screen or part to Stewart,
transportation (freight) expenses to and from Stewart are payable by the
purchaser and Stewart is not responsible for damage in shipment. To
protect yourself against damage or loss in transit, insure the product and
prepay all transportation expenses.
This warranty is in lieu of all other warranties, expressed or implied,
including warranties as to fitness for use and merchantability. Any implied
warranties of fitness for use, or merchantability, that may be mandated by
statue or rule of law are limited to the one (1) year warranty period. This
warranty gives you specific legal rights, and you may also have other rights
which vary from state-to-state. In no event will Stewart be liable for sums in
excess of the purchase price of the product. No liability is assumed by
Stewart for expenses or damages resulting from interruption in operation of
equipment, or for incidental, direct, or consequential damages of any
nature.
In the event that there is a defect in materials or workmanship of a Stewart
Screen, you may contact our Customer Service Department at
1161 W Sepulveda Blvd, Torrance, California 90502-2797
(310-784-5300) Toll free (800-762-4999).
IMPORTANT: This warranty shall not be valid and Stewart shall not be
bound by this warranty if the product is not operated and maintained in
accordance with Stewart's written instructions.
Stewart Filmscreen Corporation shall not be liable for any and all
consequential damage(s) occasioned by the breach of any written or
implied warranty pertaining to the sale in excess of the purchase price
of the product sold.
Printed in USA. Rev. 12/14/10
Rigid Rear Projection Screens: Owner’s Manual 9
PRODUCT WARRANTY

800.762.4999 •310.784.5300 •Fax: [phone]
www.stewartlmscreen.com
October 2013
Printed in U.S.A.
©2004–2013 Stewart Filmscreen Corporation