Stewart Filmscreen B User manual

TO THE INSTALLER: BE SURE TO LEAVE THIS MANUAL WITH THE OWNER.
MB/C-1101
Model B & Model C
Electriscreens
To the Owner
Installation Instructions
Operating the Screen
Maintenance
OWNER’S MANUAL

Printed in U.S.A.
©2001 Stewart Filmscreen Corporation.

Contents
To The Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Preparing The Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Step 1. Hanging The Case . . . . . . . . . . . . . . . . . . . . . . . . . .5
Step 2. Electrical Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating The Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Adjusting The Screen Extension . . . . . . . . . . . . . . . . . . . . . .9
Screen Care And Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . .11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Model B & Model C Electriscreens: Owner’s Manual 1
Model B & Model C
Electriscreens
OWNER’S MANUAL

Congratulations on your purchase of the finest optical viewing screen
available anywhere in the world!
Please take a moment to review this manual, it will help ensure you many
years of trouble-free service from your new Stewart Filmscreen product.
About your Model B/Model C Series Electriscreen
Your Model B & Model C Electriscreens offer the most technologically
advanced roller screens in the world.
The maximum overall dimensions of the Model B screen image are 18’ high
by 26’6” wide.
The maximum overall dimensions of the Model C screen image are 25’ high
by 38’10” wide.
2Stewart Filmscreen Corporation
TOTHE OWNER

Preparation
Specifications regarding the individual screen dimensions, weight, mounting
type, and controls are provided by the factory when the unit is ordered.
Before beginning the installation:
KCheck the specifications for the type of mounting and switch
control to be used.
KEnsure that the mounting area and electrical connection are
prepared.
KCheck the size and weight of the screen to be installed so that
you can plan for the number of people required for the mounting
procedure. You need at least four people to mount the smaller
screens; more are needed for larger, heavier screens.
You will need:
KEnough ladders for the personnel supporting the screen during
the mounting process
KA level
KFasteners appropriate for the surface on which the screen is
being mounted (See instructions for the type of mount for
recommendations.)
K2 block and tackles or scissor lifts to raise the unit into place
KStandard screwdriver
K7/16” hex head screwdriver
Model B & Model C Electriscreens: Owner’s Manual 3
PREPARING THE INSTALLATION
KBefore proceeding with the installation of this screen,
take time to thoroughly read and understand these
installation and operation instructions.
KAll electrical wiring installations must conform to local
and national codes and should be performed by
qualified service personnel.
KThere are no user-serviceable parts contained within
the unit.
Caution
During installation, do not place the unit on an unstable
cart, stand, table, or ladder. The unit may fall, causing injury
to a child or adult and damage to the unit.

Unpacking
1. DO NOT remove the paper hanging from the trapdoor at this
time. You should remove it only after the unit is hung, all electrical
connections have been made, and the screen is in operation.
2. Remove the batten lock-down screws located on the back side of
the case.
4Stewart Filmscreen Corporation
Warning!
Failure to remove the batten lock-down screws can result in
permanent damage to the screen.
Factory Advisory
The factory advises against installing a concealed or
recessed electrical projection screen permanently. You
must be able to access and remove the unit should future
service be necessary.
Suggested solutions for removing the unit include:
KA removable ceiling cover plate under the mounting
location.
KAccess to the unit through an attic or overhead space.

Professional mounting techniques should be adhered to. Stewart
Filmscreen Corporation cannot be liable for substandard or faulty
installations.
Make sure that you mount the screen so that the electrical box is on the left
side (audience left).
Installing the unit
The Model B & Model C Electriscreens are ready to install into the ceiling or
soffit. A false ceiling is not intended to support the weight of a Model B &
Model C Electriscreens.
The screen can be bolted directly to the support structure or suspended. If
the unit is to be mounted to plaster, drywall, masonry, or other type of
surface, use an appropriate fastener. (These might include toggle or molly
bolts or similar fasteners.)
1. Install the unit onto the support structure making sure that the
bottom of the case is flush with the finished ceiling, if any.
2. Make sure the unit is level.
Model B & Model C Electriscreens: Owner’s Manual 5
STEP 1. HANGING THE CASE
Figure 1: Model B & Model C Electriscreens
Support Structure
Electrical
Connection
Housing

The motor requires standard 120V 60 Hz input (unless an alternate voltage
has been specified). All connections are made to the electrical box on the
side of the unit (audience left).
There are several kinds of switch controls available. Follow the installation
procedure for the type of switch control you will install.
General suggestions for wiring:
KSoldering is recommended.
KThe use of wire nuts is acceptable.
6Stewart Filmscreen Corporation
STEP 2. ELECTRICAL HOO -UP
Caution
Professional techniques need to be adhered to when
making any electrical connection. A qualified electrician
should perform these procedures.
Be sure to follow all standard safety procedures for
installing electrical devices.
Do not disassemble or alter the configuration of the motor
or the unit's electrical connections. This may cause injury to
you or damage to the product.
The electrical connection should be made only to the type
of power source indicated on the marking label.

Installing the low-voltage 3-button switch (standard)
The Stewart Filmscreen low-voltage control allows the use of low-voltage
wire to connect to the supplied 3-position 24V momentary wall switch.
Preparing the connection
Before making the electrical connections, you need:
KAn available 120V AC constant power source
KA 4-conductor switch hook-up cable (4-conductor bell wire or
category 5 cable is typically used for long runs)
Making the connection
Figure 2 illustrates the connections.
1. Remove the J-box covers, using a standard screwdriver.
2. Connect the 4-conductor cable to the connection harness coming
from the J-box used for switch input, via an electrical knockout.
3. Connect the hookup cable to the 3-button switch.
4. Connect the main 120V AC power source to the the J-box used
for the main AC power connection, via an electrical knockout.
5. Replace the covers on the J-boxes.
6. A parallel connection to an outboard audio-visual switching
network can be made at this time. (optional)
Figure 2: Low voltage 3-button switch wiring
3-button Momentary
Switch
Model B & Model C Electriscreens: Owner’s Manual 7
4 Conductor Hook-up Cable - 20ga Minimum
Category 5 recommended
(NOT Supplied)
J-box for
Switch Input Note: There are three
perforated electrical knockouts
on each J-box; any can be used
to make the connection.
J-box for
Power Input
COMMON-White
UP-Red
DOWN-Black
STOP-Yellow
NEUTRAL-White
GREEN-Ground
HOT-Black

Use the 3-button switch or outboard switching network to control the screen.
When you lower or retract the screen, it will stop at its preset limit. If an
obstacle (such as a person or furniture) gets in the path of the screen as it
is lowered, you should use the switch control to stop the screen's motion; it
will not automatically stop if it hits an obstacle.
In general, when the screen is not in use, you should store it in the fully
retracted position.
8Stewart Filmscreen Corporation
OPERATING THE SCREEN
Caution
Do not operate the motor when any of the following occurs:
KThe unit emits any smoke, heat, abnormal noise or
unusual odor.
KThe unit is damaged in some way, such as damage
from a water leak.
If any of these situations occur, call a qualified service
person.
First time operation
The first time you operate the screen, the protective paper
will fall out as the screen unrolls. Once the screen is fully
displayed, make sure that no packing paper remains on the
screen roll. The screen can be damaged if loose paper
remains.

Model B & Model C Electriscreens: Owner’s Manual 9
The extension and retraction limits have been preset at the factory. In
general, we advise you to avoid readjusting these limits.
In some cases, to enable proper alignment of the displayed image on the
screen, you may need to adjust the extension of the screen. If adjustment to
the extension is necessary, carefully follow these instructions.
Caution
Improper adjustment of the limits can cause irreparable
damage to the screen itself, resulting in voiding the factory
warranty.
Warning!
The screen is fully retracted when the batten is flush with
the bottom of the case. Do not attempt adjustments with
the blue retraction (UP) thumbwheel that will further retract
the screen. Incorrect adjustment of the thumbwheel will
cause severe screen damage. Please consult the factory if
you have any questions.
ADJUSTING THE SCREEN EXTENSION
Figure 3: Underside view
Thumbwheels
Timing unit assembly;
contains limit switches

10 Stewart Filmscreen Corporation
Modifying the extension of the screen
You can increase the extension of the screen up to 3" past the factory
preset stop, or you can decrease the extension by approximately 4-6" from
the factory preset stop. Do not attempt to modify the screen extension
beyond these recommended amounts.
The thumbwheels are located on the left side of the screen roller tube inside
the case, as shown in Figure 3. Remove the cover of the case using a
7/16” hex head screwdriver. When finished, replace the cover.
To increase the screen's fully extended (screen down) stop position:
1. Lower the screen to its current stop position.
2. Locate the red extension (down) thumbwheel located on the left
side of the screen tube. Turn the thumbwheel in the direction of
the (+) sign. If the power is on, the screen will drop incrementally
as the thumbwheel is turned.
Note: One complete turn of the thumbwheel will make
approximately a 3/4" change in the screen's stop position.
To decrease the screen extension:
1. Lower the screen until it is extended about halfway down.
2. Locate the red extension (down) thumbwheel located on the left
side of the screen tube. Turn the thumbwheel in the direction of
the (-) sign.
Note: One complete turn of the thumbwheel will make
approximately a 3/4" change in the screen's stop position.
3. Activate the screen in the down direction until it reaches the
newly reduced stop position. Repeat this procedure until the
desired stop position is reached.
Once you have made the adjustment, whenever you lower the screen, it will
automatically stop at the new position.
Note: It is recommended that you make a note of any changes made to the
factory preset.

Model B & Model C Electriscreens: Owner’s Manual 11
With reasonable care, you may expect many years of trouble-free use of
your Stewart projection screen.
We encourage you to keep your screen clean. To protect your screen when
it is not in use, store it in the fully retracted position.
Avoid getting any foreign material on the screen, as cleaning may prove
very difficult. It may not be possible to remove scratches, paint, ink, etc.
General maintenance
The screen surface on your Model B & Model C Electriscreens is delicate.
Special attention to these instructions should be followed when cleaning.
KA draftsman-style brush may be used to lightly whisk away any
loose dirt or dust particles. (This type of brush is usually available
at office supply stores.)
KFor tougher spots, use a mild solution detergent, water, and a
sponge. Rub lightly. Blot with a damp sponge to absorb excess
water.
Do not use any other cleaning materials on the screen.
Replacement parts and service
No user-serviceable parts are contained within the unit. Contact your dealer
or the factory if you require part replacement or service.
SCREEN CARE AND CLEANING

Refer to the following guidelines if you encounter a difficulty in the operation
of your Stewart Filmscreen. Problems related to electrical or motor function
may require a qualified service person or electrician.
Should you have a problem that is not addressed here, call the Stewart
Filmscreen Corporation.
12 Stewart Filmscreen Corporation
TROUBLESHOOTING
Problem description Probable cause Action to take
Screen won't operate. No 120V power available.
Outboard switching problem.
Check to see if the circuit breaker
has switched off. Reset if needed.
Check outboard switching apparatus.
Check voltage availability. Contact
an electrician.
Screen won't roll up or down
(even though power is available).
Bad connection at switch. Have an electrician or qualified
service person check the
low voltage
control
switch-line connections.
Screen roller chatters when
power is activated.
Can be caused by voltage drop,
bad connections, or a defective
switch.
Have an electrician or qualified
service person check all hook-ups
including all outboard wiring.
Unit hums in up mode. (Screen
has already retracted.)
The screen batten is retracting
too far into the case. Failure to
correct can damage motor and
screen. Do not use the unit
until this problem is resolved.
Have a qualified service person
adjust the blue UP extension
thumbwheel. See pp. 9-10 of this
manual.
Screen drops when up direction
is activated (grinding noise
occurs).
Drop in voltage. Screen motor requires full voltage.
Have an electrician or qualified
service person check available
voltage.
Screen continues past bottom
stop position.
Red extension thumbwheel is out
of adjustment.
Readjust the red DOWN extension
thumbwheel. See pp. 9-10 of this
manual.
Batten retracts too far into case. Blue extension thumbwheel is
out of adjustment. Failure to
correct can damage motor and
screen. Do not use the unit
until this problem is resolved.
Have a qualified service person
readjust the blue UP extension
thumbwheel.
Dirt, finger prints, marks, etc. on
screen surface.
Improper handling of screen. Brush off or use a mild detergent
solution with clean rag or cotton
swab.
Indentations appear on screen
surface.
Debris or particles adhering to
screen due to static cling.
Check back of screen; gently brush
debris away by hand.

MAINTENANCE NOTES

www.stewartfilm.com
1-800-762-4999 KFax [phone]