Sunjoy 222255 User manual

IF YOU PURCHASED THE GAZEBO ONLINE AND
HAVE
ANY
QUESTIONS OR CONCERNS
PLEASE CONTACT YOUR SELLER FIRST
GO TO YOUR ORDER DETAILS,
CLICK ON THE SELLER NAME,
THEN “ASK A QUESTION” OR “CONTACT SELLER” BUTTON
OTHERWISE
PLEASE VISIT OUR WEBSITE AT:
www.sunjoyonline.com
OR TOLL FREE AT:
1-866-578-6569
8:30 AM EST TO 8:30 PM PST
SUNJOY INDUSTRIES GROUP
LIMITED
619 Slack
Street
Steubenville, Ohio 43952 US
ASSEMBLY INSTRUCTIONS
ITEM# L-GZ798PST-E (A)
SKU# 222255/222256
GAZEBO REGENCY DLX
Production Number: 2020200007

SAFETY INFORMATION:
Please read and understand this entire manual before attempting to assemble or install the product.
 When installing and assembling the item, it is recommended two or more adults are involved
 This product is intended for outdoor use only and should be placed on flat, horizontal ground
 Do not use the unit during an electrical storm, as there is a remote chance of getting struck by
lightning
 Do not climb on top of the item. Falling off it can result in serious injury, possibly even death
 Do not use open-flame appliances or accessories near the gazebo
 This package contains small items and plastic bags that should be kept away from children
 Ensure all connectors and poles are firmly secured in position. It is important to do so before use
to avoid collapsing or damage to the item, which could result in injury
 Center hook’s maximum weight capacity is 26 lbs
WARNING:
Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets
CPAI-84 specifications for flame resistance. It is not fireproof. The fabric will burn if left in continuous
contact with any flame source. The application of any foreign substance to the tent fabric may render
the flame-resistant properties ineffective. Remove the roof canopy during severe weather conditions
such as sustained strong winds, hurricanes, tropical downpours and snow. The manufacturer or retailer
is not liable for any loss of the product or other items due to the failure to take down the item during any
inclement weather. It is critical to secure assembled gazebo to the ground with provided stakes or bolt
it down to the patio/deck with 16 appropriate bolts/screws (not included). Make sure you have required
hardware prior the assembly.
PREPARATION:
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product. Please, write down the list of damaged/missing part names. If you purchased the item
online, you have 30 days to communicate any issue to the seller. Make sure you contact seller directly
not the marketplace. Replacement parts will be provided free of cost.
If you discovered an issue past 30 days of delivery or purchased an item at a brick and mortar store,
please call us toll free at: 1-866-578-6569
Estimated Assembly Time: 60 minutes
No tools required; 3-5 foot step ladder is recommended for assembly.

Description Part Qty Image
Corner Panel A 4
Long Cross Beam 1 B 2
Long Cross Beam 2 C 2
Short Cross Beam 1 D 2
Short Cross Beam 2 E 2
Oblique Beam F 4
Long Middle Beam G1 2
Short Middle Beam G2 2
Bottom Long Middle Beam
H 2
Bottom Oblique Beam 1 J1 2
Bottom Oblique Beam 2 J2 2
Big Roof Connector K 1
Hook L 1
Small Roof Oblique Beam
M 4
Small Roof Connector N 1
Corner Shelf O 4
Big Canopy P 1
Small Canopy Q 1
Parts List

Fig.1: Spread the Corner Panels (A) on the ground, approximately 10 feet apart
Fig.2: Insert Long Cross Beams (B and C) into each other, tighten with Knobs (S); insert Short Cross Beams
(D and E) into each other, tighten with Knobs (S)
Fig.3: Connect Corner Panels (A) with assembled Cross Beams (B-C and D-E); make sure you aligned beams
properly with rails inside, not outside of the frame
Mosquito netting
R 1
Knob
S 12
Plastic Ring
AA 52
7” Ground Stakes
BB 16

Fig.4: Insert the Oblique Beam (F) into Bottom Oblique Beam (J1&J2), you will assemble four Oblique Beams
Fig.5,6: Ask your assistant to step on the ladder and hold Big Roof Connector (K) in the middle of the Gazebo;
one-by-one insert assembled Oblique Beams F-J1 and F-J2 into the Corner Panels (A), then into the Big
Roof Connector(K); make sure you align beams properly (see illustration)
Fig.7: Insert the Middle Beam
（
G1
）
into the Bottom Middle Beam (H), you will assemble two Long Middle
Beams
Fig.8,9: Insert one end of the assembled Long Middle Beam (G1-H) into Short Cross Beam (D-E), then the
other end of the beam into the Big Roof Connector(K); tighten with the Knob (S); repeat for the other side
Fig.8,9: Insert one end of the Short Middle Beam (G2) into Long Cross Beam (B-C), then the other end of the
beam into the Big Roof Connector(K); tighten with the Knob (S); repeat for the other side
Place the Big Canopy (P) on the roof, spread it but do not stretch it yet; the canopy is rectangular, make
sure you align it properly
Fig.10: While it is still on the ground, insert the Small Roof Oblique Beam (M) into the Small Roof Connector
(N); repeat for all four beams
Fig.11: Place and stretch the Small Canopy (Q) to the small roof frame and stretching it to fit.
Fig.12: Lift the assembled small roof and insert it
into the Oblique Beams (F); attach the Hook (L)
to the Big Roof Connector
FF
J2 J2
J1
F
K
AAAA
H
G1 G2
NM
M
L
P
G1
F
G2
F
G1
F
G2
FK
L
Fig.9

CARE & MAINTENANCE
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it
from rusting. However, due to nature of steel, surface oxidation (rusting) will occur once this protecting coating
is scratched. This is not a defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent scratching
the paint. Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting paint.
Made in China
Fig.13: Spread Large Canopy (P) to the roof along the Oblique Beams, aligning the corners and stretching
it to fit
Fig.14: Place Corner Shelves (O) onto Corner Panels (A) as desired.
Fig.15: Hang the Mosquito Netting (R) on the cross beams rails, by using the Plastic Rings (AA)
Fig.16: Secure the assembled gazebo to the ground with the provided stakes (BB) through the bottom of
Corner Panels (A) or bolt it down to the patio/deck with appropriate bolts/screws (not included)