Sunjoy L-GZ747PST-A User manual

Sunjoy L-GZ747PST-A Lansing Gazebo
Owner’s Manual
IMPORTANT
Thank you very much for choosing Sunjoy Group.
Please take time to read these instructions thoroughly and follow each step carefully for safe and easy
operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. You can call us toll-free at
1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST. You can also send the email to
[email protected] or visit www.sunjoyonline.com to get tech. assistance or to place your
replacement part order form.
Production Number: 2017xxxx

Cautions:
1. Keep all children and pets away from assembly area. Children and pets should be supervised when they are
in the area of gazebo construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Four people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to reduce the
risk of personal injury and damage to equipment. Please read all instructions before assembly and use.
6. For outdoor use only. Install on level ground. Do not cook inside the tent.
7. Check all bolts for tightness before and during usage
8. Pegs supplied must be used to hold this gazebo in place when upright.
9. Warranty does not cover damage due to extreme weather conditions.
10. Do not use candles, matches or open flames of any kind in or near a tent.
11. Build campfires downwind and several meters away from a tent and be sure to fully extinguish campfires
before leaving a campsite or before retiring for the night.
12. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use
battery-operated lanterns whenever possible.
13. Extinguish or turn off all lanterns before going to sleep. Do not smoke in a tent.
14. WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is
made with fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof. The fabric will
burn if left in continuous contact with any flame source.
Assembly Instructions:
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The
final product will be a quality piece that will go together smoothly and give years of enjoyment.
All you will need is a screwdriver, a hammer and two ladders of at least 8 feet (2.5 m) high (not included).
Loading limit of the hook is 45 lbs.
Loading limit of side shelf is 45 lbs.
Parts identification: For ease of identification, all parts are labeled to correspond to the Step number in which
the part is used.
Parts List
AA M6x15 Bolt 12PCS
BB M6 Flat Washer 64PCS
CC Mosquito Netting Rings 48 PCS
DD M6x35 Bolt 32 PCS
EE M6 Nut 20PC
FF Dia. 6 X 230 Stake 16PCS
GG Wrench 2PCS

egamIytQnoitpircseD#traP
A1 Screen1 4
A2 Screen 2 4
B1 Beam1 4
B2 Beam 2 4
CShelf4
DConnector 4
EBig Canopy 1
FBeam 4
GLower Tube 4
HMiddle Beam 4
ITop Connector 1
JMosquito Netting 1
KTop Hook 1
LSmall Canopy 1
Parts List

Assembly
1 2
□
□
□
3
4
□
□
NOTE: To avoid destroying the finish, please handle it with
care.
Insert Beam 1(B1) into Beam 2 (B2) and secure together
using Bolt (AA) and Flat Washers (BB). Repeat for each
Beam 1(B1) and Beam 2(B2).
Attach the Lower Connectors (D) to the Beams (B1 and B2)
using Bolts (AA) and Flat Washers (BB).
Assembling the Beams Assembling the Screens
Attach Screen 2 (A2) to Screen 1 (A1) using Bolts (DD) Flat
Washer (BB). Repeat for the remaining Screens (A1 and A2).
Secure the Beams (B1 and B2) to the Screens (A1 and A2)
using Bolts (DD) and Flat Washers (BB).
Connecting the Beams and
the Screens
Connecting the Lower Tubes to
the Screens
Insert the Beam (F) to the Lower Tube (G).

Assembly (continued)
5 6
□
□
7 8
□
□
Insert the assembled Beam (F) into the small connector
tube of the Top Connector (I). Then install the Hook (K)
to the Top Connector (I).
Attaching the Top Connector
Insert the Lower Tubes (G) into the Screens (A1 and A2).
Connecting the Lower Tubes
to the Screens
Insert the upper end of the middle Beam (H) into the Top
Connector (I). Without unfolding, place the Big Canopy (E)
on the assembly.
Attaching the Big Canopy
Put the lower end of the Middle Beams (H) into Connectors (D)
and secure them together using Bolts (DD), Flat Washers (BB)
and Nuts (EE). Then put the Big Canopy on and do not unfold first.
Attaching the Middle Beams

Assembly (continued)
9 10
□
□
11 12
□
□
Attaching the Small Canopy
Assemble the four corners of the Small Canopy (L),
then unfold the big canopy.
NOTE: To avoid destroying the finish, please handle it
with care.
Attaching the Shelves
Put the shelves (C) on the lower beams of the
Screens (A1 and A2).
Hanging the Mosquito Netting
Use the Rings (CC) to hang the Mosquito Netting (J)
to the Beams.
Securing the Gazebo
Secure the whole Gazebo to the ground using Stakes (FF).

Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it
from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective
coatings are scratched. This is not a defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent scratching
the paint. Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting
paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If surface
oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck
or patio and caused damaging stains, which may be difficult to remove. This can be prevented if the
above-mentioned measures are taken to keep the product from oxidizing.
Limited Manufacturer’s Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal, residential
purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1) year. We
don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for
assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered.
Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser
and is non-transferable. Any replacement of warranted items will be in the original style and color, or a similar
style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions
or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives
you specific rights, and you may also have other rights, which vary from state to state.
Made in China