Sunjoy L-GZ1023PST-A User manual

Assembly Instructions
Model: L-GZ1023PST-A
SKU: 2721826
10x10 Gazebo W/ Awning

Congratulations on your purchase of our SUNJOY 10x10 Gazebo W/ Awning. Our
clear, easy to follow, step-by-step instructions will guide you through the assembly
process from start to finish.
IMPORTANT:
1. When installing and assembling your gazebo, it is recommended that two or more adults
are involved.
2. Do not use the gazebo during an electrical storm, as there is a remote chance of getting
struck by lightning.
3. Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury,
possibly even death.
4. Do not leave the gazebo assembled when there is a risk of high wind, as possible
damage will occur to the structure.
5. Do not use lanterns that contain open flames.
6. This package contains small items and plastic bags that should be kept away from
children.
7. Ensure that all connectors & poles are firmly secured in position fully. It is important to do
that before use so as to avoid collapsing or damage to the item, which could result in injury.
8. KEEP ALL FLAME AWAY FROM THIS SHELTER FABRIC. The fabric may burn if it is
exposed to prolonged contact with a flame source. The application of any foreign
substance to the fabric may render the flame-resistant properties ineffective.
USE & CARE:
1. This gazebo is not a permanent structure. The canopy top should never be left on during
periods of extended or heavy rain nor any inclement weather where high winds or wind
gusts can occur. If left up, damage to the gazebo and surroundings can occur.
2. Do not repack your gazebo until completely dry.
3. Steel components for garden accessories and furniture are treated with rust inhibiting
paint that protects them from rust. However, due to the nature of steel, surface oxidation
(rusting) will occur if this protective coating is scratched. This is a natural process. To
minimize this condition, it is recommended that care be taken when assembling and
handling the product in order to prevent the paint from being scratched. Surface rust can be
removed easily using a very light application of common cooking oil. If surface oxidation
(rusting) occurs and no measures are taken to correct it, the oxidation may start dripping
onto the deck or patio, which may cause damaging stains that may be difficult to remove.

Stake Cover
A
4
Decorative part
B
1
Stake plate
C
4
Post 1
D1
2
Post 2
D2
1
Post 3
D3
1
Short beam
E1
4
Long beam
E2
4
Beam support tube
E3
4
Middle beam connector
F
4
Oblique beam
G1
4
Oblique beam down tube
G2
4
Middle beam
H1
4
Middle beam down tube
H2
4
Tabletop
I
1
Tabletop support
J
1
Small top connector
K
1
Small top oblique beam
L
4
Big top connector
M
1
Hook
N
1
Barometric bar
S
2
Awning frame corner
part
O1
2
Parts List

AA
M6*15 Flat bolt
16PCS
BB
M6 Washer
58 PCS
CC
M6*15 Hex bolt
34 PCS
II
M6*25 Hex bolt
8PCS
Z
M6 Wrench
1 PC
Hardware Pack 1
Awning frame horizontal
pipe 1
O2
2
Awning frame horizontal
pipe 2
O3
2
Awning frame vertical
pipe 1
O4
1
Awning frame vertical
pipe 2
O5
1
Awning frame support
pipe
O6
1
Awning frame locating
piece
O7
1
Big canopy
P
1
Small canopy
Q
1
Awning
R
1

BB
M6 Washer
16 PCS
DD
M6 Nut
8 PCS
EE
M6*40 Flat bolt
8 PCS
Hardware Pack 2
Fig.4: Use bolt (CC) and washer (BB) to fasten the beams(E1,E2) on the posts(D1,D2,D3), then use
bolt (II) and washer (BB) to fasten the beam support tube on the beam (E1, E2).
Fig.5: Firstly inset the tabletop (I) connector into the U plate on the posts (D2, D3). Then use bolt
(CC) and washer (BB) to fasten the tabletop on the post (D2, D3).
Fig.6: Use bolt (CC) and washer (BB) to fasten the tabletop support (J) beneath the table.
Fig.1: Firstly attach the bottom of posts (D1,D2, D3) into stake cover(A) and raise them up. Then use bolt
(AA) and washer (BB) to fasten the stake plate(C) on the bottom of posts.
Fig.2: Attach the short beam (E1) with long beam (E2) tightly using bolt (CC) and washer (BB).
Fig.3: Use bolt (AA) and washer (BB) to fasten the middle beam connector (F) on the assembled beams.

Fig.10: Firstly insert the middle beam (H1) into the down tube (H2).
Fig.11: Insert the middle beam (H1) into the big top connector (M), then attach the hook(N) on the
big top connector(M).
Fig.12: Use bolt (EE), washer(BB) and nut (DD) to fasten the middle beam down tube (H2) on the
middle beam connector(F), then cover the big canopy(P) but do not unfold it.
Fig.13: Attach the small top oblique beam (L) with small top connector (K).
Fig.14: Cover the small canopy (Q) on the assembled small top.
Fig.15: Attach the decorative part (B) on the small top.
Fig.7: Insert the oblique beam (G1) into the down tube (G2).
Fig.8: insert the oblique beam (G1) into the big top connector (M).
Fig.9: Use bolt (EE), washer (BB) and nut (DD) to fasten the oblique beam down tube (G2) on the
U plate of posts (D1, D2, D3).

Hardware Pack 4
Fig.16: Attach the assembled small top on the tube of oblique beam (G1) through small top oblique
beam (L).
Fig.17-1: Cover the big canopy (P) on the big top, then button up canopy on the oblique beam
down tube (G2).
Fig.17-2: Cover the four cloth buttons which in the middle of big canopy (P) on the middle beam
down tube (H2).
CC
M6*15 Hex bolt
28PCS
BB
M6 Washer
28 PCS
HH
M6 antiskid nut
2 PCS
FF
∮8*180 Stake
16PCS
GG
M6*90 Flat bolt
2pcs

Fig.18 Insert the awning frame part into the awning (R) as the pic. shows, and use velcro to fasten the
vertical pipe ((O4,O5)) on the awning (R). The outside horizontal pipe (O2，O3) and support pipe(O6)
also use velcro to fasten to awning (R),but the inside horizontal pipe (O2,O3) insert to awning (R).
Fig.18-1: Insert the horizontal pipe 2 (O3) into the horizontal pipe 1(O2), then use bolt (CC) and washer
(BB) to fasten it.

Fig.18-2: Use bolt (CC) and washer (BB) to fasten the awning frame support pipe (O6) on the
assembled awning frame 1(O2) and awning frame 2(O3).
Fig.18-3: Insert the horizontal pipe 2(O3) and Awning frame vertical pipe 2(O5) into the awning frame
corner part（O1）, then use bolt (CC) and washer (BB) to fasten it. Awning frame horizontal pipe 1
(O2)andAwning frame vertical pipe 1(O4) and awning frame corner part（O1）as the same method.
Fig.18-4: Insert the horizontal pipe 1 (O2) into the vertical pipe (O4), then use bolt (CC) and washer
(BB) to fasten it. Awning frame horizontal pipe 2(O3) and Awning frame vertical pipe 2(O5) as the same
method.
Fig.19: Use bolt (GG) and nut (HH) to fix the assembled awning frame on the post (D2/D3).
Fig.20: Use bolt (CC) and washer (BB) to fasten Barometric bar to the Awning and post
(D2/D3).
Fig.20-1: Use bolt (CC) and washer (BB) to fasten awning frame locating piece (O7) on the
post 2(D2).
Your 10x10 gazebo is now ready for use.
Please do not return this product to the store. For technical assistance on assembly
or replacement parts call Sunjoy Industries at 1(866) 578-6569 from 8:00 AM to 8:00
PM EST or Email [e-mail] or visit www.sunjoyonline.com to
place your order or fax your parts replacement order form together with your
purchase receipt to 1 [phone] for assistance.
Fig.20-2: When lay down the awning frame, pl hook it using awning frame locating piece lest
wind blows it up.
Fig.21: Use stake (FF) to fix the gazebo on the lawn.