Sunjoy L-GZ137PST-1B User manual

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The
final product will be a quality piece that will go together smoothly and give years of enjoyment.
Note: THIS UNIT IS HEAVY!
DO NOT assemble this item alone for safety. Four people are necessary.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which
the part is used.
Warnings:
1. Assembly Instructions must be followed.
2. Pegs supplied must be used to hold this gazebo in place when upright.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
It is not fire proof. The fabric may burn if left in continuous contact with any flame source.
ASSEMBLY INSTRUCTIONS
ITEM# L-GZ137PST-1B
AVALON GAZEBO 10’x12’

Screen (1) A 4
Screen (1) B 4
Small screen C 8
Decor C1 8
Screen connector D 8
Short bar E 2
Long bar E1 2
Tilted top bar F 4
Tilted top bar connector (1) F1 2
Tilted top bar connector (2) F2 2
Long top bar G 2
Short top bar H 2
Small top bar I 4
Big top connector J 1
Small top connector K 1
Pothook L 1
Short mosquito pipe M 4
Long mosquito pipe N 4
Planter basket O 4
Big canopy Q 1
Small canopy R 1
Mosquito net S 1
Tools required : hammer, ladder, screwdriver (not included)
Parts List

AA M6X20 (Bolt)
TBZ00306020HQ 16 PCS
BB M6 (Washer)
TBZ10406HQ 24 PCS
CC M6X35 (Bolt)
TBZ00106035HQ 8 PCS
Z M6 (wrench) 1 PC
Hardware Pack 1
Fig.1: Attach the decor (C1) and the small screen (C).
Fig.1-1: Connect the screen (C) and screen (A & B) by using Bolt (AA) and washer (BB).
Fig.2 & Fig.3: Connect the screen B and screen A with Bolt (CC) and washer (BB), tighten by using
wrench (Z).

BB M6 (flat washer)
TBZ10406HQ 48 PCS
II M6X20 (Bolt)
TBZ00106020HQ 16 PCS
DD M6X15 (Bolt)
TBZ00306015HQ 32 PCS
Hardware Pack 2
BB M6 (washer)
TBZ10406HQ 12 PCS
EE M6X35 (Bolt)
TBZ00306035HQ 8 PCS
FF M6(nut)
TBZ20106HQ 8 PCS
Hardware Pack 3
Fig.4: Insert Screen connector (D) into long and short bar (E1, E) separately, tighten them with Bolt (DD) and
flat washer (BB).
Fig.5: Connect the screen A (B) and Screen connector (D) by using Bolt (II) and flat washer (BB) to form a
basic frame.
Fig.5-1: Attach the mosquito pipe N (M) to the beam E1 (E) and Screen A (B) by using Bolt (DD) and flat
washer (BB)

Fig.6: Insert the tilted top bar connector F1 (F2) into the top screen corner.
Fig.7 & Fig.7-1: Attach the pothook (L) to Big top connector (J), insert four tilted top bar (F) into big top
connector (J). Then insert the tilted top bar (F) into tilted top bar connector F1 (F2). At last, insert the long side
top bar (G), short side top bar (H) into the big top connector (J).
Fig.8: Attach long side top bar (G), short side top bar(H) to short bar (E) and long bar (E1), tighten them by
using Bolt (EE), Flat washer (BB) and Nut (FF).
Fig.9: Insert small top bar (I) into small top bar connector (K) to form a small top frame.
Fig.10: Put big canopy (Q) on the big top, but do not fully spread. Fix the small top onto the tilted top bar (F)
by using bolt (EE), washer (BB) and nut (FF).

GG
Φ6*180MM (Round nail)
TBZ10606180HQ 16 PCS
HH Plastic hang ring 44 PCS
Hardware Pack 4
Fig.11 : Fix small canopy (R) and then spread the big canopy (Q). Then hang the mosquito net (S) to mosquito
pipe M (N) by using plastic hang ring (HH). You also can hang the privacy panels (not included) to the pipe M
(N).
Fig.12: Fix the assembled gazebo on the ground by using round nail (GG).
Fig.13: Hang the planter basket (O) to the ring on the screen.
Now, your Gazebo is ready for use.
S

IMPORTANT:
1. Keep all children and pets away from assembly area. Children and pets should be supervised when they are
in the area of gazebo construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Four people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to reduce the
risk of personal injury and damage to equipment. Please read all instructions before assembly and use.
6. For outdoor use only. Install on level ground. Stakes are provided to secure the gazebo in the ground. If you
wish to secure the gazebo to a wood deck or concrete surface, you will need to purchase fasteners appropriate
for these surfaces. These are readily available at your local hardware store or home center.
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for,
or otherwise regulate, installation and use.
9. While this gazebo is manufactured to withstand gale force winds utilizing only the supplied ground stakes, in
areas subject to frequent severe weather, securing the gazebo to a deck, concrete patio or footings should be
considered.
10. Your gazebo has been engineered to accommodate winter snow loads incurred in most areas. Removal of
accumulated snow on the gazebo roof with a roof rake is recommended. In areas that are regularly subject to
blizzard conditions however, removal of the roof panel is suggested. The assembled roof structure can simply
be left intact until warmer conditions return.
CARE & MAINTENANCE:
1. This Gazebo is not a permanent structure and should be disassembled & stored away after use.
2. Do not repack your gazebo until completely dry.
3. This Gazebo must not be left erect in windy conditions.
Made in China