Sunjoy L-GZ238PST-10 User manual

Questions, problems, missing parts? call our customer service department at
1-866-578-6569 from 8:00 am EST to 8:00 pm PST, or email to
[email protected]
ITEM # L-GZ238PST-10
Assembly Instructions

1
PACKAGE CONTENTS
B
D
O1
L1
L2
L3
P2
P1
H
R
U1 U2 M1
Q
K4
K3
K2
K1
N2
N4
N6
G1
J
N1
N3
N5
F
X
A1
C
V
T
A2
G2
W
I
O3
E
O2
M2
S

2
PART
A1
A2
B
C
D
E
F
G1
G2
H
I
J
K1
K2
K3
K4
L1
L2
L3
M1
M2
N1
N2
N3
N4
N5
N6
O1
O2
O3
P1
P2
Q
R
S
T
U1
U2
V
W
X
2
2
4
4
2
2
2
2
2
1
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
1
1
2
2
1
2
4
Pole (1)
Pole (2)
Base
Base cover
Long screen
Short screen
Beam connector (middle)
Beam connector (corner) (1)
Beam connector (corner) (2)
Small top frame
Corner top beam
Middle top beam
Long and big roof panel (1)
Long and big roof panel (2)
Long and big roof panel (3)
Long and big roof panel (4)
Short and big roof panel (1)
Short and big roof panel (2)
Short and big roof panel (3)
Long and small roof panel (1)
Short and small roof panel (2)
Long side beam (1)
Long side beam (2)
Long side beam (3)
Long side beam (4)
Long side beam (5)
Long side beam (6)
Short side beam (1)
Short side beam (2)
Short side beam (3)
Corner covering of big top (1)
Corner covering of big top (2)
Middle covering of big top
Small top beam
Connector of small top
Hook
Covering of small top (1)
Covering of small top (2)
Small top cap
Shelf
Support bar
DESCRIPTION QUANTITY
PACKAGE CONTENTS

HARDWARE CONTENTS
M6×15
Bolt
M6×15
Hex Bolt
M6×25
Hex bolt
M6×30
bolt
Qty. 84
AA
SAFETY INFORMATION
WARNINGS
• This product is intended for outdoor use only and should be placed on flat, horizontal ground.
• Ensure enough clearance around the product.
• Before assembling the product, find level ground no less than 6 ft. away from any structures or
obstructions, such as fences, garages, houses, overhanging branches, laundry lines, or electrical wires.
• The gazebo must be anchored with stakes onto the ground for added safety.
• It cannot be permanently attached to a concrete floor or platform.
• Do not assemble the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage
in these types of soil.
• This product is for outdoor use only! Do not climb on top of the gazebo! Do not use the unit during an
electrical storm!
CAUTIONS
• Any assembly or maintenance of the product must be carried out by adults only.
• Arrange 6 or more manpower when assembling or moving the product.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• Check all nuts and bolts periodically for tightness. When required, tighten them again.
• Do not hang any weights on the roof frame.
• Always keep children under close supervision when they are using or are around this product. Never
leave children unattended.
Hook maximum weight: 33 lbs
M6 Washer
Qty. 181
BB
M6 Nut
Qty. 16
CC
Qty. 16
M6×55
Bolt
Qty. 22 Qty. 22 Qty. 20
DD EE FF GG
Please read and understand this entire manual before attempting to assemble, operate or install the
product. If you have any questions regarding the product, please call our customer service department
at 1-866-578-6569 from from 8:00 am EST to 8:00 pm PST. or email to
[email protected]
M6 Nut
with cap
Qty. 1
HH
M6
Wrench
Qty. 1
Z
3
Φ8×180
Stake
Qty. 16
I I

Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble the
product. Contact customer service for replacement parts.
Estimated Assembly Time: 90 minutes
Tools Required for Assembly: Wrench (included) and Phillips Screwdriver (not included)
PREPARATION
4
x 8
M6x15 Bolt
x 8
M6 Washer
ASSEMBLY INSTRUCTIONS
1. Insert the pole (A1 and A2）into the base cover (C),
and then install the base (B), securing with bolts (AA)
and washers (BB).
Hardware Used
B
1
C
BB
Fig. 1
Fig. 2
Fig. 3
Fig. 4
BB
AA AA
AA
BB
A2A1
A1
C
B
A1
A2
A2
D
E
E
G1 G1
G2
G2
D
F
F

x 16
M6 Washer
ASSEMBLY INSTRUCTIONS
2. Connect the long screen (D) and short screen (E)
to the pole (A1 and A2), securing with bolts (CC)
and washers (BB).
Hardware Used
2
D
D
F
E
A2
D E
A2A1
G2
BB CC
BB
BB
DD
BB
DD
BB
DD
BB
DD
CC
BB
x 16
M6x25 Hex bolt
CC
3. Attach the beam connector (corner) (2) (G2) to
the top of pole (A2), securing with blots (DD) and
washers (BB). Repeat this procedure for beam
connector (corner) (1) (G1).
3
4. Connect the beam connector (middle) (F) to
middle of the long screen (D) by using blots
(DD) and washers (BB).
4
5
x 8
M6 Washer
Hardware Used
BB
x 8
M6x15 Hex bolt
DD
x 4
M6 Washer
Hardware Used
BB
x 4
M6x15 Hex bolt
DD

Fig. 5
Fig. 6
Fig. 13
Fig. 11
Fig. 9 Fig. 10
Fig. 12
Fig. 8
Fig. 7
Fig. 14
ASSEMBLY INSTRUCTIONS
BB EE
BB EE
BB EE
H
I
G1
O3
FF BB
FF
G1 G2
BBF
FF BBF
N5
N6
O2
G2
N3
II
I
RR
H
S
T
O1 N1 N4
N2
5&6. Connect the corner top beam (I) to the beam
connector (corner) (G1 and G2), securing them
with blots (EE), washers (BB) and nuts (FF).
Connect the other end of corner top beam (I) to
the small top frame (H).
5
6
6
Hardware Used
x 24
M6 Washer
BB
x 12
M6x55 Bolt
EE
x 12
M6 Nut
FF

ASSEMBLY INSTRUCTIONS
7&8. Connect the middle top beam (J) to the small
top frame (H) by blots (EE), washers (BB) and
nuts (FF). Connect the other end of the middle
top beam (J) to the beam connector (middle) (F).
7
Hardware Used
x 12
M6 Washer
BB
x 6
M6x55 Bolt
EE
x 6
M6 Nut
FF
9&10. Connect the long side beam (N1 and N3) to
the corner top beam (I), securing them with
blots (AA), washers (BB). Connect the other
end of long side beam (N1 and N3) to the
middle top beam (J). Repeat this procedure
for the long side beam (N2 and N4).
Hardware Used
x 16
M6x15 Bolt
AA
x 16
M6 Washer
BB
BB
BB
FF
BB
BB
FF
BB
FF
J
J
J
H
F
EE
BB EE
BB EE
N1 N3
N1 N3
I
AA
7
8
K
9
10

8
Hardware Used
x 8
M6 Washer
BB
x 4
M6x55 Bolt
EE
x 4
M6 Nut
FF
BB AAI
N5
J
R
H
N5
R
S
T
BB
BBFF BB EE
AA
ASSEMBLY INSTRUCTIONS
11&12. Connect the long side beam (N5) to the
corner top beam (I), securing them with
blots (AA), washers (BB). Connect the
other end of long side beam (N5) to the
middle top beam (J). Repeat this procedure
for long and short beam (N6, O1, O2, O3).
Hardware Used
x 20
M6x15 Bolt
AA
x 20
M6 Washer
BB
11
13. Attach the hook (T) to the connector of small
top (S); connect the small top beam (R) to the
connector of small top (S), securing them with
blots (EE), washers (BB) and nuts (FF).
14. Insert the small top beam (R) to the
small top frame (H).
13
14
12

Fig. 18
Fig. 16
Fig. 15
Fig. 20
Fig. 22
Fig. 19
Fig. 21
Fig. 17
A1 A1
V
M1
M2
U
U2 U1
K4
K3
L3
L2
L1
L1
L2
L3
K1
QK2
K3
K4
K1 K2
P2
P1
W
W
X
X
X
A2
A2
9
BB
AA BB
AA BB
AA
BB
AA BB
AA
BB
AA
BB
AA
BB
AA
BB
AA
BB
AA
ASSEMBLY INSTRUCTIONS
15. Connect the long and big roof panel
(K1, K2, K3, K4) and short and big
roof panel (L1, L2, L3) by using blots
(AA) and washers (BB).
x 28
M6x15 Bolt
AA
x 28
M6 Washer
BB
Hardware Used
15