Sunjoy L-GZ240PST-C User manual

Assembly Instruction
ITEM# L-GZ240PST-C
10'x12' Soft Top Gazebo

IMPORTANT:
Please read and follow all safety statements, warnings, assembly instructions,
use & care directions, before attempting to assemble.
WARNINGS:
1. Assembly Instructions must be followed.
2. Pegs supplied must be used to hold this gazebo in place when upright.
3. Warranty does not cover damage due to extreme weather conditions.
4. Do not use candles, matches or open flames of any kind in or near a tent.
5. Do not cook inside the tent.
6. Build campfires downwind and several meters away from a tent and be sure
to fully extinguish campfires before leaving a campsite or before retiring for the
night.
7. Exercise extreme caution when using fuel-powered lanterns or heaters
inside a tent and use battery-operated lanterns whenever possible.
8. Do not refuel lamps, heaters or stoves inside a tent.
9. Extinguish or turn off all lanterns before going to sleep.
10. Do not smoke in a tent.
11. Do not store flammable liquids inside a tent.
12. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT
FABRIC. This tent is made of flame-resistant fabric. It is not fireproof. The
fabric will burn if left in continuous contact with a flame source.

Small top connector A1 1
Top connector A2 1
Finial B1 1
Hook B2 1
Top cant beam
connector 1 C1 4
Top cant beam
connector 2 C2 4
Arch beam 1 D 4
Arch beam 2 E 4
Horizontal beam 1 F 4
Horizontal beam 2 G 2
Horizontal beam 3 H 2
Post 1 I 4
Post 2 J 4
Fence K 4
Small canopy L 1
Big canopy M 1
Mosquito netting N 1
Netting Tube1 O1 2
Netting Tube 2 O2 2
Netting Tube 3 O3 4
Parts List

AA M6*15 Bolt 32 PCS
BB M6 Flat washer 64 PCS
CC M6*35 Bolt 16 PCS
W M6 Wrench 1 PCS
GG M6*15 Screw 16PCS
Hardware Pack 1

Fig.1: Connect horizontal beam 1 (F) to post 1 (I) or post 2 (J) with bolt (AA) and flat washer
(BB). (Note: Put canopy hook hole outwards when attach horizontal beam1 (F).)
Fig.2: Connect fence (K) to post 1 (I) or post 2 (J) with bolt (CC) and flat washer (BB).
Fig.3: Connect horizontal beam 3 (H) to post 1 (I) or post 2 (J) with bolt (AA) and flat washer
(BB). (Note: Put canopy hook hole outwards when attach horizontal beam 3 (H).)
Fig.4: Connect horizontal beam (2) (G) to post 1 (I) or post 2 (J) with bolt (AA) and flat
washer (BB). Lock all bolts tightly by wrench (W).
Fig.5: Connect netting tube 1 (O1) to horizontal beam 3 (H) with screw (GG) and flat washer
(BB). Lock all bolts tightly by wrench (W). Use the same way to lock other netting
tubes to corresponding beams.
DD Ф6*180 Stake 16 PCS
Hardware Pack 2

Fig.6: Insert top cant beam connector 2 (C2) into top connector (A2), at the same time, insert hook
(B2) into top connector (A2).
Fig.7: Insert arch beam 1(D) and arch beam 2(E) into top cant beam connector 2 (C2). Sort order of
arch beam 1(D) and arch beam 2(E) is as below figure shows.
Fig.8: Insert tube of arch beam (D、E) into post 1 (I) and post 2 (J). Put big canopy (M) onto big top.
Fig.9: Insert top cant beam connector 1 (C1) into small top connector (A1), put on small canopy (L),
at the same time, insert finial (B1) onto small top connector (A1).
Fig.10: Put small canopy (L) onto small top firstly, then insert connection strap of top cant beam
connector 1 (C1) to top cant beam connector 2 (C2). At last, hang hook of big canopy (M) to
horizontal beam.
Fi
g
.11: Secure assembled
g
azebo to lawn b
y
stake
(
DD
)
.
FF Ring 52 PCS
Hardware Pack 3
Fig.12: Hang mosquito netting (N) to netting tubes
with ring (FF).