Sunjoy L-GZ660PST User manual

Sunjoy L-GZ660PST Capri Gazebo
Owner’s Manual
IMPORTANT
Thank you very much for choosing Sunjoy Industries.
Please take time to read these instructions thoroughly and follow each step carefully for safe and easy
operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. You can call us toll-free at
1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST. You can also send the email to
[email protected] or visit www.sunjoyonline.com to get tech. assistance or to place your
replacement part order form.

Cautions:
1. Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of gazebo construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence,
garage, house, overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Four people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. Do not cook inside the tent.
7. Check all bolts for tightness before and during usage
8. Pegs supplied must be used to hold this gazebo in place when upright.
9. Warranty does not cover damage due to extreme weather conditions.
10. Do not use candles, matches or open flames of any kind in or near a tent.
11. Build campfires downwind and several meters away from a tent and be sure to fully
extinguish campfires before leaving a campsite or before retiring for the night.
12. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and
use battery-operated lanterns whenever possible.
13. Do not refuel lamps, heaters or store flammable liquids inside a tent.
14. Extinguish or turn off all lanterns before going to sleep. Do not smoke in a tent.
15. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is
made of flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous
contact with a flame source.
Assembly Instructions:
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start
to finish. The final product will be a quality piece that will go together smoothly and give years
of enjoyment.
Loading limit of the hook is 45 lbs.
Loading limit of side shelf is 45 lbs.
Parts identification: For ease of identification, all parts are labeled to correspond to the Step
number in which the part is used.

A1 Small top connector 1PC
A2 Large top connector 1PC
B1 Finial 1PC
B2 Hook 1PC
C3 Small top slanting bar 4PCS
C4 Slanting bar connector 4PCS
D1 Top bar 1 4PCS
E2 Top bar 2 4PCS
E3 Top bar connector 8PCS
F Bean 1 4PCS
G Bean 2 2PCS
H Bean 3 2PCS
I Post 1 4
J Post 2 4
K Fence 4
L Small canopy 1
M Big Canopy 1
N mosquito net 1
Parts List

AA M6*15 Hexagon Bolt 32 PCS
BB M6 Washer 48 PCS
CC M6*35 Hexagon Bolt 16 PCS
W M6 Wrench 1 PCS
Hardware Pack 1
Fig.1:Attach the short beam (F) to one of the posts (I, J) using bolt (AA) and washer (BB). Tighten the bolts
using the wrench (W).
Fig.2:Attach the fence (K) to one of the posts (I, J) using bolt (CC) and washer (BB). Tighten the bolts using
the wrench (W).
Fig.3:Attach beam 3 (H) to post 1 (I) and to post 2 (J) using bolt (AA) and washer (BB). Tighten the bolts
using the wrench (W).
Fig.4:Attach the short beam (G) to one of the posts (I, J) using bolt (AA) and washer (BB). Tighten the bolts
using the wrench (W).

DD Ф6*180Stake 16 PCS
Hardware Pack 2
Fig.5:Insert one end of the slanting bar connector (C4) into the large top connector (A2). Insert and screw
the hook (B2) tightly into the large top connector (A2).
Fig.6:Connect the other ends of the slanting bar connector (C4) to the top bars (D1, E2. )
Fig.7:Insert top bar 2 (E2 ) into top bar connector (E3), and top bar 1 (D1) into top bar connector (E3).
Fig.8:Insert the other ends of the top bar connectors (E3) into the posts (I, J), respectively. Then place
the large canopy (M) on the top of the frame. Do not expand the large canopy at this step.

Fig.9:Insert one end of the small top slanting bar (C3) into the small top connector (A1).
Fig.9-1:Place the small canopy (L) on the frame. Screw the finial (B1)onto the tip of the small top connector.
Fig.10:Insert the other end of the small top slanting bar (C3) into the slanting bar connector (C4).
Fig.11:Fix the assembled gazebo on the ground by using stakes (DD).
FF PlasticLoop 52 PCS
Fig.12: Hang the mosquito netting (N) on the upper tube of the beams H(F,G) using plastic rings(FF).
Hardware Pack 3

Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint
that protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will
occur once these protective coatings are scratched. This is not a defect and thus not covered
by the warranty.
To minimize this condition, we recommend care when assembling & handling the product to
prevent scratching the paint. Should any scratching or damage occur, we recommend
immediate touch-up with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If
surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may
start dripping on to deck or patio and caused damaging stains, which may be difficult to
remove. This can be prevented if the above-mentioned measures are taken to keep the
product from oxidizing.
Limited Manufacturer’s Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials
and workmanship of your item provided the item is maintained with care and used only for
personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1)
year. We don't reimburse for transportation or delivery costs, or compensate the individual or
any outside party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due
to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or
rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any
replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not
apply. This warranty gives you specific rights, and you may also have other rights, which vary
from state to state.
Made in China