Sunjoy L-GZ717PST-E-GB User manual

Sunjoy L-GZ717PST-E-GB Mirage Gazebo
Owner’s Manual
IMPORTANT
Thank you very much for choosing Sunjoy Group.
Please take time to read these instructions thoroughly and follow each step carefully for safe and easy
operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. You can call us toll-free at
1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST. You can also send the email to
[email protected] or visit www.sunjoyonline.com to get tech. assistance or to place your
replacement part order form.
Production Number: 2017xxxx

Cautions:
1. Keep all children and pets away from assembly area. Children and pets should be supervised when they
are in the area of gazebo construction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Four people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to reduce the
risk of personal injury and damage to equipment. Please read all instructions before assembly and use.
6. For outdoor use only. Install on level ground. Do not cook inside the tent.
7. Check all bolts for tightness before and during usage
8. Pegs supplied must be used to hold this gazebo in place when upright.
9. Warranty does not cover damage due to extreme weather conditions.
10. Do not use candles, matches or open flames of any kind in or near a tent.
11. Build campfires downwind and several meters away from a tent and be sure to fully extinguish campfires
before leaving a campsite or before retiring for the night.
12. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use
battery-operated lanterns whenever possible.
13. Do not refuel lamps, heaters or store flammable liquids inside a tent.
14. Extinguish or turn off all lanterns before going to sleep. Do not smoke in a tent.
15. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is made of
flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact with a flame source.
Assembly Instructions:
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The
final product will be a quality piece that will go together smoothly and give years of enjoyment.
Parts identification: For ease of identification, all parts are labeled to correspond to the Step number in which
the part is used.

NO. Name Qty. Image
A1 Post 1 2
A2 Post 2 2
B Stake Base 4
C Stake Base Cover 4
D Short side long beam 2
E Short side short beam 2
F Long side long beam 2
G Long side short beam 2
H Middle beam down
connector 4
I Finial 1
J Curved beam 4
K Curved beam down tube 4
L Long middle beam 2
M Middle beam down tube 2
N Short middle beam 2
O Short middle beam down
tube 2
P Long mosquito net rail 4
Q Short mosquito net rail 4
R Large top connector 1
S Hook 1
T Small top connector 1
Parts List

U Small top curved beam 4
V Big canopy 1
W Small canopy 1
X Curtain 1
Y Mosquito net 1
NO. Name Qty. Image
AA M6x15 Hexagon Bolt 32 PCS
BB M6 Washer 40 PCS
CC M5x15 Hexagon Bolt 24 PCS
EE M6 Hexagon Nut 8 PCS
HH M5 Washer 24 PCS
Z M5/M6 Wrench 2 PC
Hardware Pack 1

BB M6 Washer 16 PCS
DD M6x40 Hexagon Bolt 8 PCS
EE M6 Hexagon Nut 8 PCS
Hardware Pack 2
Fig.1: Put base cover (C) into
post (A1, A2), then attach base
(B) to post (A1, A2) with Bolt
(AA) and washer (BB).
Fig.2: Insert long side long beam
(F) into long side short beam (G),
then fix with bolt (AA), washer (BB)
and nut (EE). Repeat this step for
short beam
(
D, E
)
.
Fig.3: Attach Long side Long
beam (F) to Post (A1) with Hex
Bolt (AA) and Washer (BB),
Repeat this step for Long side
short beam (G), short beam.
(D, E).
Fig.4: Attach Middle beam
down connector (H) to Long
side Long beam (F) Long side
short beam (G) with Bolt (CC)
and Washer (HH). Repeat this
step for short beam (D, E).
Fig.5: Attach Long mosquito net
rail (P) to Long side beam (F,G)
with Bolt (CC) and Washer (HH).
Repeat this step for short beam
(D, E).

Fig.6: Insert Curved beam
(J) into Curved beam down
tube (K).
Fig.7: Insert Curved beam (J)
into Large top connector (R),
then fix hook (S) onto large top
connector
(
R
)
.
Fig.8: Attach Curved beam
down tube (K) to Posts (A1,
A2) with Bolt (DD), Washer
(BB) and Nut (EE).
Fig.9: Insert Long middle
beam (L) into Middle beam
down tube (M). Repeat this
Step for Short middle beam
(N) and Short middle beam
down tube (O).
Fig.10：Insert Long middle
beam (L) into Large top
connector (R). Repeat this
step for Short middle beam
(N).
Fig.11: Fix Middle beam
down tube (M) and Short
middle beam down tube (O)
onto Middle beam down
connector (H) with Bolt
(DD), Washer (BB) and Nut
(EE). Put Big canopy (V) on
Big Top, but do not spread it
now.
Fig.12: Insert small top
curved beam (U) into small
top connector (T).
Fig.13: Insert small top
curved beam (U) into
Curved beam (J).

FF φ8*180 Round Stake 16 PCS
GG Plastic Loop 104 PCS
Hardware Pack 3
Fig.14:Put small canopy
(W) on small top, then
attach four corners of small
canopy to small top curved
beam (U).
Fig.15: Attach finial (I) to
small top connector (T).
Fig.16 ：Spread out Big
canopy (V) , Attach on the
corners of Curved beam
down tube (K), Middle beam
down tube (M) and Short
middle beam down tube (O).

Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it
from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective
coatings are scratched. This is not a defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up with rust
inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking oil. If surface
oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on to
deck or patio and caused damaging stains, which may be difficult to remove. This can be prevented if the
above-mentioned measures are taken to keep the product from oxidizing.
Limited Manufacturer’s Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal, residential
purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1) year. We
don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for
assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of
nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not
covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original
purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color,
or a similar style and color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply. This
warranty gives you specific rights, and you may also have other rights, which vary from state to state.
Made in China
Fig.17: Hang mosquito nets (Y) and
curtains (X) onto long mosquito net
rails (P) and short mosquito net rails
(Q) with plastic rings (GG).
Fig.18: Lift base cover (C),
secure the whole gazebo to the
lawn by inserting stakes (FF) in
the holes of each base.