Sunjoy L-GZ778PST-A User manual

SAFETY INFORMATION:
Please read and understand this entire manual before attempting to assemble or install the product.
When installing and assembling the item, it is recommended two or more adults are involved.
This product is intended for outdoor use only and should be placed on flat, horizontal ground.
Ensure enough clearance around the product.
Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightning.
Do not climb on top of the item. Falling off it can result in serious injury, possibly even death.
Never barbecue under this item or use lanterns that contain open flames.
This package contains small items and plastic bags that should be kept away from children.
Ensure all connectors and poles are firmly secured in position. It is important to do so before use to avoid
collapsing or damage to the item, which could also result in injury.
Center hook’s maximum weight capacity is 26 lbs.
WARNING:
Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84
specifications for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any
flame source. The application of any foreign substance to the tent fabric may render the flame-resistant
properties ineffective. Remove the roof during severe weather conditions such as sustained strong winds,
hurricanes, tropical downpours and snow. The manufacturer or retailer is not liable for any loss of the product
or other items due to the failure to take down the item during any inclement weather.
ASSEMBLY INSTRUCTIONS
ITEM# L-GZ778PST-A
SKU# 036805
10' X 10' ELSWORTH GAZEBO

CARE AND MAINTENANCE:
This item is intended for decorative and sunshade purposes only, and is not designed to withstand
severe weather, including high winds, sustained tropical downpours, and snow. In order to avoid damage
in such instances, remove any accumulated water and the roof immediately. Disassemble the item in the
reverse order of the assembly steps if necessary prior to a severe storm.
A partially disassembled item is likely not stable enough to resist high winds and other severe weather,
and therefore can be damaged and/or cause damage. Since assembly time is only approximately 20
minutes, complete disassembly is recommended prior to any major storm.
Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
Steel components of garden accessories and furniture are treated with rust inhibiting paint. However, due
to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a
natural process. To minimize this condition, it is recommended that care be taken when assembling and
handling the product, in order to prevent the paint from being scratched.
Surface rust can be removed easily using a very light application of common cooking oil. If surface
oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto
the assembly surface, which may cause damaging stains that may be difficult to remove.
If the product will not be used for a long period (e.g. winter time), it should be stored in a clean, dry
environment.
Keep the original packaging to store the item.
PREPARATION:
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents
list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes or less (2 persons)
Only a step ladder is needed for assembly, no other tools required.

Corner Panels A 4
Cross Beam B 4
Corner Shelf C 4
Middle Bar Connector D 4
Slanting Bar Connector E 4
Upper Slanting Bar F 4
Lower Slanting Bar G 4
Middle Bar H 4
Top Connector I 1
Slanting Bar Connector
Base J 4
Hook K 1
Small Canopy L 1
Large Canopy M 1
Bolt N 16
Parts List
GG Φ6x180MM Stake 16 PCS
Hardware Pack

ASSEMBLY INSTRUCTIONS:
Fig.1: Unfold corner panels (A), then insert the cross beam (B) into
the groove of the corner panels (A) and secure the cross beam with
bolt (N).

Fig.2: Insert the slanting bar connector base (J) into the respective slots on the top of each corner panels (A).
Fig.3: Insert the slanting bar connector (E) into the slanting bar connector base (J), and secure slanting bar
connector using bolt (N). Please do not tighten the bolt here.
Fig.4: Insert the middle bar connector (D) into the cross beam (B), and secure middle bar connector using bolt
(N). Please do not tighten the bolt here.
Fig.5: Insert the upper slanting bar (F) to the lower slanting bar (G).
Fig.6: Insert the lower slanting bar (G) into the slanting bar connector (E).
Fig.7: Insert the upper slanting bar (F) into the top connector (I), then screw the hook (K) into the top
connector (I).
Fig.8: Insert one end of the middle bar (H) into the middle bar connector (D).
Fig.9: Insert the opposite end of the middle bar (H) into the top connector (I). Please tighten all the bolts.
Place the large canopy (M) to the roof, do not spread it.

Now, your Gazebo is ready for use.
Made in China
Fig.10: Attach the small canopy (L) to the top along the upper slanting bar (F), aligning the corners and
stretching it to fit.
Fig.11: Spread the large canopy (M) to the roof along the lower slanting bar (G), aligning the corners and
stretching it to fit. Attach the sides of the large canopy (M) to the end of middle bar (H).
Fig.12: Place the corner shelves (C) onto the corner panels (A) as desired.
Fig.13: Secure the assembled gazebo to lawn with stakes (GG) through the bottom of corner panels (A).