Sunjoy Tivoli L-GZ105PST-4 User manual

1
Tivoli Gazebo
Style #L-GZ105PST-4
DPCI# 009-05-0182
Congratulations –You’ve purchased a fine item from Target.
Our clear, easy to follow; step by step instructions will guide you through the project from start to finish. Feel confident
that this will be a fun and rewarding project. The final product will be a quality piece that will go together smoothly and
give years of enjoyment.
All you will need is a hammer, and a ladder at least 8.2 ft. high (or 2.5m).
If you have any questions, just call 866-578-6569. Please refer to the DPCI code above when calling.
WARNING:
•THIS UNIT IS HEAVY!
•Do not assemble this item alone for safety. Two persons are necessary.
•Some parts may contain sharp edges –especially as noted in manual. Wear protective gloves if
necessary.
•Do not play with the construction of the arbor. Children and pets should be supervised when they are in
area of the arbor. Do not allow the gate or the side panel to collide hard to avoid danger.
•Read all instructions before assembly and using this product.
•Select ideal location. Set out all parts on a clear and level surface prior to assembly. Ideally, the gazebo frame
should be set up in its desired location to avoid moving it after assembly.
•Use caution. During all the process of assembling, especially when lifting heavy or large parts, pay attention to safety.
•Tools and Assistance. Ladder and wrench are self-provided. Whenever possible, assistance is preferred.
•Check for parts available. Before assembling your gazebo, be sure that you have all parts described in the Parts List.
•Check for damaged parts. Before assembling your gazebo, check for damaged parts, any part that appear
damaged should be carefully checked to determine that it will be operated properly and perform its intended
function. Any part that is damaged should be properly repaired or replaced by a qualified technician.
•Refer to assembly diagram. During assembly, it will be helpful to referring to the assembly diagram.
•Keep children away. Children must never be allowed in the work area. Do not let them handle parts and tools.
No people will be permitted to enter into work area except who is working.
•Caution for fabric: Keep all flame and heat sources away from this gazebo fabric. This gazebo is made with
fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof. The fabric will burn with
continuous contact with any flame source.
Step #1: Set up panels;
Step #2&3: Set up the top frame;
Step #4: Put on top canopy,
mosquito netting and fix the
whole product.
Product Size identification: 10’L x 10’W
Recommended persons for safe assembly: 3.

2
Parts List
Part Description
Part #
Qty.
Part Image
Large Upper panel
A
4
Large Bottom Panel
B
4
Smaller Upper panel
C
4
、
Smaller Bottom Panel
D
4
Long Bar
E
4
Short Bar
F
8
Corner Connector
G
4
Top Bar 1
H
4
Top Bar 2
I
4
Panel Connector 1
J
12
Panel Connector 2
K
4
Top Center Connector
L
1
Canopy
M
1
Mosquito Netting
N
1
Corner Bracket
O
4

3
Spare Hardware Pack
Hardware Identification
For ease of identification, all hardware is
organized into separate hardware packs as
below. Actual size is not shown below.
AA
M5x30 Bolt
16 pcs
BB
M5 Flat Washer
32 pcs
WW
M5 Wrench
1 pc
CC
M5x15 Bolt
16 pcs
Hardware Pack 1
CC
M5x15 Bolt
8 pcs
BB
M5 Flat Washer
8 pcs
DD
￠4.5 x180 Stake
16 pcs
EE
Plastic Ring
40pcs
Hardware Pack 2
AA
M5x30 Bolt
2 pcs
BB
M5 Flat Washer
4 pcs
CC
M5x15 Bolt
2PCS
FF
Spring Clasp
2 pcs
EE
Plastic Ring
4 pcs
ZZ
Touch Up Paint
1 pc

4
`
Step #1
Fig. 2-1
A
C
AA
BB
A
C
J
J
B
D
AA
BB
Fig. 2-2
AA
BB
D
B
Fig. 1
CC
BB
Hardware Pack1
Panels (hardware pack 1)
AA
M5x30 Bolt
16 pcs
BB
M5 Flat Washer
32 pcs
CC
M5x15 Bolt
16pcs
WW
M5 Wrench
1 pc
1. Use panel connector (J) (Note: surface with thread should face the hole) to assemble large upper panel A and
large bottom panel B. Use panel connector J and (K)（Note: surface with thread should face the hole) to fix smaller
upper panel C and smaller bottom panel D. Use bolt (AA) and flat washer (BB) to fasten the assembled large panels
and smaller panels as shown in Fig. 1. Use bolt (CC) and flat washer (BB) to fasten the assembled large panels in
Fig. 1；And use bolt (CC) and flat washer (BB) to fasten smaller panels as shown in Fig. 1.
2. Use bolt (AA) and flat washer (BB) to fasten the top and bottom of the panels as in Fig. 2-1 and Fig. 2-2.
K
BB
AA
CC
BB
CC
BB
J
CC
BB

5
Top Frame - 1
No Hardware needed for this step
Step #2
Fig. 3
Fig. 4
3. Insert one end of two short bar (F) into long bar (E), as in Fig. 3
4. Insert the other end of the short bar (F) into the panel (A) and (c), as in Fig. 4
F
F
E
Fig. 3
Fig. 4
A(C)

6
Top Frame –2 (Hardware pack 2)
CC
M5x15Bolt
8 pcs
BB
M5 Flat Washer
8 pcs
H
L
Fig. 7
H
H
Step #3
Fig. 6
6. Insert the corner connector (G) into the panel
corners, as in Fig. 6.
7. Insert the other end of top bar (H) into top
center connector (L), as in Fig. 7.
8. Insert the other end of top bar (I) into corner
connector (G), as in Fig. 8
BB
CC
Fig. 5
H
I
G
H
Fig. 8
I
G
Fig. 8
Fig. 5
Fig. 7
Fig. 6
5. Insert top bar 2 (I) into top bar 1(H) and use bolt
(CC) and flat washer (BB) to fasten them, as in
Fig. 5.

7
9. Put on canopy (M). And then use Plastic Ring (EE) to hang on mosquito netting (N) onto the hanging bar, as
shown in Fig. 9. Attach the corner brackets (O) onto the panels.
10．Use Stakes (DD) to fix the gazebo on ground, as shown in Fig. 10.
Step #4
EE
N
Fig. 9
Fig. 10
Fig. 9
M
Canopy, Mosquito Netting, and Stakes (Hardware pack 2)
DD
￠4.5 x180 Peg
16 pcs
EE
Plastic Ring
40pcs
DD
DD
Fig.10

8
Care & Maintenance
Steel components for garden accessories and furniture are treated with rust inhibiting paint that protects them from rust.
However, due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a
natural process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product in order to prevent the paint from being scratched. If scratching or damage occurs, it is recommended that the
area be touched-up immediately with rust inhibiting paint, which is included in the package. Surface rust can be
removed easily using a very light application of common cooking oil. If surface oxidation (rusting) occurs and no
measures are taken to correct it, the oxidation may start dripping onto the deck or patio, which may cause damaging
stains that may be difficult to remove.
Limited Warranty
Sunjoy Industries warrants to the original purchaser that this item is free from defects in workmanship and materials for
a period of one (1) year from the date of purchase, provided the item was factory-sealed at the time of purchase and is
maintained with care and used only for personal, residential purposes. Should any manufacturing defect arise within
this warranty period, Sunjoy Industries will repair or replace (at our option) any defective merchandise upon proof of
purchase; however, transportation and delivery costs, as well as labor and material charges to remove or replace parts,
remain the responsibility of the purchaser. A purchaser of an "open box," previously-returned, or "clearance" item, as
well as original purchasers outside of the warranty period, may obtain replacement parts from Sunjoy Industries for
products in current production, at nominal cost.
Exclusions: Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of
nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not
covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original
purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color, or a
similar style and color if the original is unavailable or has been discontinued. As some states do not allow exclusions or
limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific
rights, and you may also have other rights, which vary from state to state.
IMPORTANT: Please do not return this product to the store. For technical assistance on assembly or
replacement parts, please do not return this product to the store, call Sunjoy Industries at 866-578-6569 from 8:30 AM
to 5:30 EST Monday to Friday or fax the replacement part form which is included in the package to 740-283-3549 or
Email [email protected] for assistance.