Sunnydaze Decor TF-580 User manual

Page 1 / 3
  
A
Top Pole 1
B
Bottom Pole 1
CLeg 4
  
DBolt 4
EWasher 4
F
M8x55MM
2
This egg chair stand is not
designed for use as a swing.
Bouncing, swinging, or any other
signicant movements while in
use may cause serious injury.
This stand must be on a level,
stable surface. Make sure all
hardware is securely tightened
before each use.
Weight Limit: 265 lbs.Weight Limit: 265 lbs.
EGG CHAIR STAND
WITH CURVED LEG BASE
TF-580
Read all assembly and care instructions carefully before using this product.
Save these instructions for future reference.


  
XHex Key 1
ZSpanner 1
CHOKING HAZARD — This item
contains small parts that can be
swallowed. Keep children away
during assembly.
TF
Ensure all parts are accounted for
before disposing of packaging.
07/2020
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
CAUTION
WARNING

ASSEMBLY
Page 2 / 3
Assembly Tip: Ensure all parts and
hardware align correctly before fully
tightening the lock nuts.
1. Slide Leg (C) into Bottom Pole (B).
Align the holes on the underside of
each piece. Hand-tighten Bolt (D)
and Washer (E). Repeat until all legs
are attached. Tighten all bolts using
Hex Key (X).
2. Slide Top Pole (A) onto Bottom Pole
(B) and align the holes. Secure the
poles by hand-tightening M8x55MM
hardware (F) through the top holes.
Repeat with the bottom holes. Fully
tighten the hardware using Hex Key
(X) and Spanner (Z). Place the hex
nut cap over the lock nut.
A
TF
D
X
E
1
X
Z
F
2
B
Cx4
07/2020

• Do not exceed the weight capacity: 265 lbs
• Sunnydaze Egg Chair Stand is intended to be used by one person at a time.
• This chair Stand must be used with all provided parts. Install all parts in accordance with the assembly instructions.
• Ensure all hardware is securely installed and tightened before each use.
• Always inspect the stand and hardware for damage before each use.
• Do not allow children to use this product without adult supervision.
• This stand was designed for sitting calmly in an egg chair. Egg chair
not included.
• Do not swing, bounce, jump, twist, or spin in the chair (not included)
when using this egg chair stand.
• When in use, the chair (not included) should remain inside the base
area at all times. A diagram of the base area is shown on the right.
USE & CARE
Under normal use, Sunnydaze hammock stands will last for years. It is important to follow basic use & care
tips to prolong the life of your stand.
• SAFE USE: Do not use this chair for swinging, bouncing, jumping, twisting, or other excessive movements;
doing so may cause serious injury, including, but not limited to, the stand tipping over.
• CHILDREN: Supervise children at all times. Do not allow children to play on or sleep in any hanging chair.
Chair not included.
• INSPECTION: Ensure the stand is assembled correctly and all hardware is securely tightened before each
use.
• CLEANING: Use a soft cloth, warm water and mild detergent to wipe down the stand if necessary. Dry the
stand after cleaning to prevent rust.
• SCRATCHES: The powder coating on the stand is tough and durable but, even under normal use, some
scratching is inevitable. To avoid excessive rust, wipe these areas as needed to remove moisture.
• STORAGE: Store the stand indoors when not in use. Cool, dry locations are recommended to prevent
damage and rust that may result from exposure to moisture.
TROUBLESHOOTING
• If the stand feels unstable, make sure it is on a level surface and the feet are correctly and evenly distributed.
• If the stand is making noise when in use, check to make sure all hardware is fully tightened.
WARNING:
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,

Page 3 / 3TF 07/2020

SAFETY STATEMENTS & WARNINGS