superbrightleds ELS-RW User manual

LED Emergency Light
Important: Read all instructions prior to installation. ELS-RW
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V0.1 11/05/2018
Included Parts
Specications
Safety and Notes
ELS-RW
Total Power Consumption 1.9 Watts
Operating Voltage Range 120/277 VAC
Operating Temperature 50°–104° F (10°–40° C)
Environmental Rating damp or dry location
Fixture Weight 3.75 lb (1.7 kg)
Recommended Mounting 7.5 ft (2.3 m) high, 26 ft (7.9
m) center-to-center spacing
between lights
1 - xture
1 - hardware kit
• This product should be installed and serviced by a certied electrician
in accordance with applicable national, state, and local building and
electrical codes.
• Light must be maintained, tested, and serviced in accordance with all
applicable National Fire Protection Association (NFPA) and local codes.
• To reduce the risk of electric shock, ensure that the main power source
and circuit breakers are switched o󰀨 before performing any installation
or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the weight
of the xture. Failure to properly support xture may result in damage
or injury, for which the manufacturer does not assume responsibility.
• Intended for indoor use only.
• Do not mount near radiant heat sources/heaters.
• Use caution when handling or servicing the battery pack.
Testing
Manual Test
Test button can be held to illuminate lights for manual
testing purposes.
120 V Wiring
277 V Wiring
Wiring Diagram
BLACK
WHITE
GREEN
ORANGE
120 V POWER
NEUTRAL
GROUND
N/C
BLACK
WHITE
GREEN
ORANGE
N/C
NEUTRAL
GROUND
277 V POWER
BLACK
WHITE
GREEN
ORANGE
120 V POWER
NEUTRAL
GROUND
N/C
BLACK
WHITE
GREEN
ORANGE
N/C
NEUTRAL
GROUND
277 V POWER
User Manual
¹
¹Limited 2-year warranty on battery.

Installation Instructions
Dimensional Drawings
1. Remove two screws holding front cover in place.
2. Remove appropriate knockouts for wiring
and mounting from real panel.
3. Using an appropriate strain relief (not included), run wiring
through rear panel. Connect wiring to junction box and cap
unused wire. (refer to wiring diagram)
Note: Orange and black wires should never be connected
at the same time.
4. Securely attach light to junction box with included hardware.
5. Connect battery.
6. Reattach front panel.
7. Apply power and allow battery pack to charge for at least
24 hours before initial use/test.
8. After 24-hour period, press test button to make certain
lights are functioning as intended and are aimed correctly.
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V0.1 11/05/2018
LED Emergency Light
Important: Read all instructions prior to installation. ELS-RW
Wiring Holes
Junction Box
Mounting Holes
Wall Mounting
Holes
Battery Connection
M4 x 7mm Phillips
Screw
10.38
263.65
6.38in
162.05mm
12.25in
311.15mm
2.38in
60.45mm
.85in
21.59mm
3.55in
90.18mm
0.85in
21.59mm
8.58in
217.93mm
2.49in
63.25mm
2.49in
63.25mm
.85in
21.59mm
CONDUIT KNOCKOUT
CONDUIT
KNOCKOUT
CONDUIT KNOCKOUT
User Manual
¹
¹Limited 2-year warranty on battery.