superbrightleds NFLSK-W600-VCT User manual

NFLSK-W600-VCT
Instruction Sheet
Part Number:
Parts Included
Important: Read all instructions prior to installation.
Tunable White Flexible
Light Strip Kits Pre-test & Congure
Remove strip from reel and make connections to power supply
and controller (see “Method 1” diagram). Breiy turn on strip
using the included remote controller to ensure proper operation
of the strip, power supply, controller, and remote.
Layout strip near surface of desired application, hold strip up
near mounting surface to determine the total length of the strip
needed for your installation. See below for cutting instructions
and cut off any excess strip.
See “General Diagram” for guide to installing and connecting
LED strip to included power supply and controller for your
application. Choose your desired yet suitable location for the
power supply and controller, routing IR sensor of controller to
convient line-of-sight location for general use with IR remote
control.
Ensure all installation surfaces are clean and dry.
Begin to remove strip’s backing while adhering to desired
mounting surface. Press rmly to secure strips to surface. Route
strip around corners carefully, do not kink strip. Traces on the
circuit and other circuit components can be damaged if strip is
not adhered to surface carefully. Attach controller and power
supply to desired location using included foam tape.
Cutting
Cut strips to appropiate length using scissors
on lines indicated with scissor icon. Strip can
only be cut on these lines, which are spaced
every 12 LEDs.
Instructions
(Method 1) Complete Kit Connection
Connecting Strips
866-590-3533 [email protected]
1 - 16.5’ (5m) LED Flexible Light Strip (NFLS-W600-VCT)
1 - Tunable White Controller with IR Remote (VCT-CON)
1 - 24VDC 48W CPS Power Supply (CPS-24VDC-48W)
3 - Double-Sided Foam Pads (3M-FTP)
If your installation requires additional parts, visit superbrightleds.com and
enter the part number above in the search box.
V+ W P
V+ W P
Power Supply
(CPS-24VDC-48W)
Tunable White
Controller (VCT-CON)
Tunable White
600 High Power LED
Flexible Light Strip
(NFLS-W600-VCT)
V+ W P
V+ W P
V+ W P
IR Controller IR Remote
Mode Function Brightness Speed
1 Warm White Adjustable Not Adjustable
2 Cool White Adjustable Not Adjustable
3 Natural White Adjustable Not Adjustable
4 Strobe Change Adjustable Adjustable
5 Fade Change Not Adjustable Adjustable
Button Functions
ON/OFF Turn strip on and off,
retaining the last setting
MODE Cycle through 3 static and 2
dynamic modes
BRIGHTNESS Dim strip while on the
adjustable modes
SPEED Adjust dynamic mode
pattern speed.
IR remote controller has a signal range
up to 15ft (4.5m) and requires line-of-
sight to VCT-CON Variable Color Temp.
Controller.
Mode Selection

Note: This conguration is for installation under the counter of a typical bar top with an existing outlet near or inside of bar as a power source for the
power supply. Wiring may vary based on bar conguration and outlet availability.
General Diagram
DO NOT connect LED strip directly to 120V AC power. This kit requires a 24V DC Adapter (included power supply) to be powered.
DO NOT connect more than one 16.5’ section of light strips to the included power supply. Overloading the included power supply may cause
overheating, shorting, and possibly re.
Be sure the power supply is not plugged into an outlet before connecting or disconnecting any of the kits components.
DO NOT expose the light strip to direct or indirect moisture.
Always observe proper polarity when connecting power and load.
Safety
866-590-3533 [email protected]
Bar Countertop
Power Supply
Tunable White
Controller (VCT-CON)
Tunable White 600 High Power LED
Flexible Light Strip
(NFLS-W600-VCT)
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+
W
P
V+ W P
V+ W P
V+ W P
V+ W P
V+ W P
V+ W P
V+ W P
IR Controller
Tunable White 600 High Power LED
Flexible Light Strip
(NFLS-W600-VCT)
Inside of Bar
Outside of Bar
May be used along the inside of the bar
to illuminate counter and sink area.
Route strip around corners care-
fully, do not kink strip. Traces on
the circuit and other circuit com-
ponents can be damaged if strip is
not adhered to surface carefully.