superbrightleds EPLL Series User manual

Linear Explosion Proof Light
Important: Read all instructions prior to installation. EPLL Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.1 06/29/2020
User Manual
5yr
Safety and Notes
Specications
EPLL-50K40-UGN-110
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray
Green
• Product should be installed by a certied electrician in accordance with applicable national,
state, and local building and electrical codes. Proper earth grounding is required.
• To reduce the risk of electric shock, ensure that the main power source and circuit breakers
are switched o󰀨 before performing any installation or wiring procedures. If smoke is detected
or a short circuit is present, switch o󰀨 power immediately and notify relevant personnel.
• Avoid looking directly into the light when illuminated.
• Failure to properly support the xture may result in damage or injury, for which the manufacturer
does not assume responsibility. Check whether any accessories are correctly installed
prior to installation.
• If the light is damaged during shipping, do not install and contact customer service immediately.
Model EPLL -xK40-UGN-110 -xK80-UGN-110 -xK120-UGN-110
Operating Temperature -40°–122° F(-40°–50° C)
IP Rating IP66
Fixture Weight 16.9 lb (7.7 kg) 25.5 lb (11.6 kg) 26.1 lb (11.8 kg)
Conduit Installation
Chain Installation (EPLL-HM)
Wire Guard Installation (EPLL-WG)
Safety Cable Installation
Pipe Mount Installation (EPLL-PM220)
Ø10 mm
Ø170 mm
Yoke Mount Installation (Included)
1. Attach mount to light.
2. Drill 10 mm mounting holes 170 mm apart.
3. Hammer in mounting bolts into ceiling.
4. Fasten yoke mount/light assembly to mounting bolts until secure.
5. With supply power o󰀨, open driver box and connect wiring.
6. Rotate light to desired angle and tighten adjustment screw.

Linear Explosion Proof Light
Important: Read all instructions prior to installation. EPLL Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.1 06/29/2020
User Manual
5yr
Conduit Installation
Conduit Installation
Chain Installation (EPLL-HM)
Wire Guard Installation (EPLL-WG)
Safety Cable Installation
Pipe Mount Installation (EPLL-PM220)
Ø10 mm
Ø170 mm
1. Remove yoke mount if assembled.
2. Remove conduit plug.
3. With supply power o󰀨, open driver box, feed
wire into box, and make all wiring connections.
4. Ensure silicone gel is added around the
threads and securely install conduit pipe/nut.
Note: All conduit openings must be closed by
conduit or NPT nut.
5. Close access panel and re-install screws.

Linear Explosion Proof Light
Important: Read all instructions prior to installation. EPLL Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V1.1 06/29/2020
User Manual
5yr
Wire Guard Installation (EPLL-WG)
Safety Cable Installation
Pipe Mount Installation (EPLL-PMx) Installation
Conduit Installation
Chain Installation (EPLL-HM)
Wire Guard Installation (EPLL-WG)
Safety Cable Installation
Pipe Mount Installation (EPLL-PM220)
Ø10 mm
Ø170 mm
Conduit Installation
Chain Installation (EPLL-HM)
Wire Guard Installation (EPLL-WG)
Safety Cable Installation
Pipe Mount Installation (EPLL-PM220)
Ø10 mm
Ø170 mm
Conduit Installation
Chain Installation (EPLL-HM)
Wire Guard Installation (EPLL-WG)
Safety Cable Installation
Pipe Mount Installation (EPLL-PM220)
Ø10 mm
Ø170 mm
1. Remove yoke mount if assembled.
2. Measure diameter of pipe to select correct pipe mount hardware.
3. Drill and tap holes to align with two holes in bracket where the wing
bolts go to keep the light from being able to rotate on the pipe.
4. Slide pipe rings over pipe, then attach to light bracket using nuts
and wing bolts.
5. Attach light to bracket.
6. With supply power o󰀨, open driver box and make all wiring
connections.
1. Locate threaded holes on xture and
align wire guard to front of xture.
2. Tighten screws to secure wire guard.
1. Latch safety cable carabiner to body of light.
2. Wrap safety cable around a sturdy, load-bearing
structure and secure.