Symmons 4200TRMTC Installation instructions

Oxford®
Model Numbers
Oxford Trim Series
Oxford Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly
Installation & Operation Instructions
TRIM ONLY
4200-TRM
Shower Valve Trim
4201-TRM
Shower Trim
4202-TRM
Tub/Shower Trim
4203-TRM
Hand Shower Trim
4205-TRM
Shower/Hand Shower Trim
4206-TRM
Tub/Shower/Hand Shower Trim
Compliance
• ASME A112.18.1/CSA B125.1
Limited Lifetime - to the original end purchaser in consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete warranty information.
Go to www.symmons.com/register to register your Symmons product.
TRIM, TA-10, T-12A
4200TRMTC
Shower Valve Trim
4201TRMTC
Shower Trim
4202TRMTC
Tub/Shower Trim
4203TRMTC
Hand Shower Trim
4205TRMTC
Shower/Hand Shower Trim
4206TRMTC
Tub/Shower/Hand Shower Trim
Warranty
4200-TRM
4200TRMTC
4201-TRM
4201TRMTC
4202-TRM
4202TRMTC
4205-TRM
4205TRMTC
4203-TRM
4203TRMTC
4206-TRM
4206TRMTC
TA-10T-12A

2
1. Recommended Tools
FIGURE 2
HH
K
K
G
G
L
L
M
M
F
F
B
B
D
D
J
J
I
I
N
N
O
O
A
A
C
C
R
R
S
S
Q
Q
P
P
E
E
Floor
Floor
Notes:
1) Valve body and piping not included and shown as reference only.
2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater.
3) All dimensions measured from nominal rough-in (see R as reference).
4) Dimensions subject to change without notice.
Phillips Screwdriver
Adjustable Wrench Safety Glasses Thread Seal TapeDrill Allen Wrench (3mm)
FIGURE 1
2. Dimensions
Measurements
A 6-1/2", 165 mm
B 9-5/8", 245 mm
C 3-7/8", 98 mm
D
Male 1/2" IPS thread must
protrude 1/2" from
finished wall
E 6", 152 mm right or left
F 77", 1956
G 5", 127 mm
H 7-1/2", 191 mm
I 7", 178 mm
J 4-3/4", 121 mm
K 2-1/2", 64 mm
L
4200, 4201, 4203, 4205:
Ref. 42", 1067 mm
4202, 4206:
Ref. 32", 813 mm
M 12", 305 mm
N 2-9/16", 65 mm
O 4", 102 mm
P 1/2" NPT
Q 4", 102 mm
R(Rough in)
2" ± 1/4", 51 mm ± 6 mm
S 6-1/2", 165 mm

3
3. Parts Breakdown (Model Numbers Ending in TRMTC)
5. Installation - Adjust Packing Nut (Model Numbers Ending in TRMTC)
1) Turn hot and cold supplies on. Valve will not operate unless both hot and cold water supply pressures are on.
2) Place handle over flow control spindle.
3) Tighten packing nut for positive frictional resistance as handle is rotated from shut-o position across adjustment range.
6. Installation - Setting Limit Stop Screw (Model Numbers Ending in TRMTC)
1) Turn hot and cold supplies on. Valve will not operate unless both hot and cold water supply pressures are on.
2) Place handle on flow control spindle and open valve to maximum desired temperature.
3) Turn limit stop screw clockwise until it seats.
WARNING: Failure to adjust limit stop screw properly may result in serious scalding.
The temperature limit stop screw limits valve handle from being turned to maximum position resulting in excessive hot
water discharge temperatures.
4. Installation - Remove Test Cap (Model Numbers Ending in TRMTC)
1) Check for leaks around the valve assembly and all pipe
fittings.
Flow control spindle (TA-10) and cap assembly (T-12A) will
come factory assembled for all model numbers ending in
TRMTC. When ready to remove Test Cap and install trim,
follow the instructions below:
2) Remove test cap from valve (FIGURE 4.1).
3) If system is dirty, flush valve.
4) Thread flow control spindle and cap assembly into valve
body. Turn clockwise to secure to valve (FIGURE 4.2).
FIGURE 4.1 FIGURE 4.2
LIMIT STOP
SCREW
2
1
PACKING
NUT
FIGURE 3
Replacement Parts
Item Description Part Number
1 Cap Assy. T-12A
2 Flow Control Spindle TA-10
IMPORTANT: Model numbers ending in TRMTC
coordinate with Temptrol pressure balancing valves
ordered with Test Cap. The Test Cap is used to
allow pressurization of system. Do not remove
test cap from valve during wall construction,
installation of valve or pressurization of system.
WARNINGS:
1. Do not expose valve with test cap to heat
for longer than 2 minutes when soldering
copper tubing. Doing so may damage the
internal components of the valve and will
void the product warranty.
2. Ensure test cap is tightened securely after
soldering valve body.

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2019 Symmons Industries, Inc. ■symmons.com ■[email protected] ■ZV-3285 REV A ■ 062819
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth
defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Replacement Parts
Item Description Part Number
A Showerhead 422SH
B Shower Arm 422SA
C
D
Diverter Handle
Flange T-549-DIV
C
D
Shower Handle
Flange T-549
E
F
Lock Nut
Dome Cover T-543
G
H
I
Diverter Escutcheon
Screws
Mounting Plate
LD-132-NS
J
K
L
Dial
Screws
Mounting Plate
T-542-NS-K001
M Hand Shower 422W
N Wall Cradle T-547
O 60" Hose RTS-045
P
P2
Tub Spout
Diverter Tub Spout
422TS
422TSD
Notes:
1) Append appropriate sux for premium finish.
2) Append appropriate flow rate to showerhead
or hand shower for low flow.
3) Apply a bead of silicone around the perimeter
of all shower trim installed flush to the
finished wall. Leave opening on bottom of
escutcheons for weep hole.
4) Apply plumber tape to all threaded
connections.
FIGURE 7
P
A
B
H
H
I
C
E
D
F
G
K
K
L
C
E
D
F
J
O
N
M
P1
EF-109*
*Order in-line vacuum breaker (EF-109) for
hand shower systems without dual checks.
7. Parts Breakdown