Symmons SPP-3510 User manual

If you use soldering for the installation of your faucet, the seat
cartridges and washers will have to be removed before using
flame. Otherwise, warranty will be void on these parts.
Prior to beginning installation, turn off the cold and hot water lines
and open the old faucet to release built-up pressure.
When installing your new faucet, turn the connector nuts hand
tight, then use one wrench to anchor the fitting and a second
wrench to tighten the nut one additional turn. Connections that
are too tight will reduce the integrity of the system.
Wrap all threaded connections with Teflon tape available at your
local hardware or plumbing supply store. Always wrap in a clock-
wise direction.
Important Points
Protect your eyes with safety glasses when cutting or soldering
water supply line.
Cover your drain to avoid loosing parts.
Tools
Your new kitchen faucet is designed for years of trouble-free
performance.
Keep it looking new by cleaning it periodically with a soft cloth.
Avoid abrasive cleaners, steel wool and harsh chemicals as
these will dull the finish and void your warranty.
Safety Tips
Maintenance
Adjustable Wrench
Pliers
Pipe Wrench
Teflon Tape
Instructions For Models
SPP-3510 & SPP-3510-STN
What You Need To Have
Instructions For Models:
Phillips Head Screwdriver
HELP LINE
Need Help?
Symmons customer service:
[phone], [phone]
[e-mail]
Mon - Fri 7:30 am - 7:00 pm EST
Website:www.symmons.com
Page 1 Rev G
ZV-1083

All installations can vary depending on how your previous faucet
was installed. Necessary supplies to install your faucet are not all
included: however they are available wherever plumbing supplies
are sold. When choosing your installation supplies, make sure
they are IAPMO and / or CSA approved products.
Things You May Need
2
13
Shut off water supply. Remove old faucet. Clean sink
surface in preparation for new faucet.
Attach Spout to Valve
Feed hose assembly through spout and hub. Attach
sprayer to end of hose to keep hose in place. Rotate
spout assembly to ensure smooth operation.
Mount Faucet to Deck
Place flange on bottom of hub. Insert faucet through
mounting holes in sink. Your faucet is designed for a hole
diameter of 1 3/8" +/- 1/4"(35mm+/- 6mm) and a deck
thickness of up to 2 1/2" (64mm).
Page 2

5
4
7
Install rubber washer, metal washer and nut onto the
mounting shank.
Hose Installation
Align block (1) onto hose. Install quick connect onto spray
hose. Push quick connect firmly onto outlet hose tab.
Install weights onto spray hose. Locate the weights 24"
from the underside of the sink deck.
24"
Faucet Operation and Inspection
Turn on hot and cold water supplies. Pull the hose
assembly out of the spout and remove aerator(1) with
wrench(2). Be sure to hold the end of the hose down into
the sink and turn faucet handle to the mixed position.
Flush water lines for one minute. Check for leaks.
Re-tighten if necessary, but do not overtighten. Reinstall
the spray head tight.
1
2
Connect to water supplies (HOOK-UPS NOT PROVIDED)
Note: Refer to local plumbing codes for permissible types
of water supply connectors.
(B)
(A)
6
Page 3

RK-001RK-002
RK-002-STN
RK-005
RK-006
RK-007
Page 4
RL-032
RL-032-STN
(optional)
RK-014
RK-014
RO-006 (2.2 gpm, 8.3 L/min)
RO-007 (1.5 gpm, 5.7 L/min)
RO-008 (1.0 gpm, 3.8 L/min)
RK-022
RK-004
RK-004-STN
RK-003