Target carson CACNTBWDEB User manual

carson
console table
>> assembly instructions
style # CACNTBWDEB (black)
dpci # 249-17-0894
tcin # 53567590
style # CACNTBWDES (espresso)
dpci # 249-17-0887
tcin # 53567598
style # CACNTBWDGY (gray)
dpci # 249-17-0895
tcin # 53567613
style # CACNTBWDBR (rustic)
dpci # 249-17-0896
tcin # 53567621
style # CACNTBWDWL (walnut)
dpci # 249-17-0897
tcin # 53567589
style # CACNTBWDWH (white)
dpci # 249-17-0898
tcin # 53567603
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-16
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 26
wooden dowel
(H2) x 30
cam bolt
(H3) x 30
cam
(H4) x 20
short pan head screw
(H5) x 2
knob
(H6) x 2
knob bolt
(H7) x 5
at head screw
(H8) x 4
shelf support
(H9) x 1
wall anchor
(H10) x 1
long pan head screw
(H11) x 1
wall screw
(H12) x 1
wall strap
(H13) x 2
washer

exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side panel 1
3 right side panel 1
4 bottom panel 1
5 bottom front rail 1
6 bottom rear rail 1
7 back panel 1
8 upper front rail 1
9 upper rear rail 1
10 drawer front 1
11 drawer left side 1
12 drawer right side 1
13 drawer back 1
14 drawer bottom 1
15 drawer support 1
16 shelf 1
17 shelf rail 1
5

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
1. 2. 3.
4. 5.

step 1: attach shelf rail to shelf
(H1) x 2
wooden dowel
(H2) x 3
cam bolt
(H3) x 3
cam
1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
7
(H3) x 3

step 2: attach bottom front and rear rails to bottom panel
(H1) x 4
wooden dowel
(H2) x 6
cam bolt
(H3) x 6
cam
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
8
(H3) x 6
cam

step 3: attach upper front and rear rails/bottom panel to left side panel
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
3.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
3.2. Screw-In cam bolts must be screwed down ush.
3.3. Refer to page 6 for instructions on how to use the cam lock system.
3.4. Do not over tighten bolts.
9
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
Screw-In cam bolts must be screwed down ush.
Refer to page 6 for instructions on how to use the cam lock system.

step 4: attach right side panel
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
4.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.
10
(H2) x 4
cam bolt
(H3) x 4
cam
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
Screw-In cam bolts must be screwed down ush.
Refer to page 6 for instructions on how to use the cam lock system.

step 5: attach top panel
(H1) x 6
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
5.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
5.2. Screw-In cam bolts must be screwed down ush.
5.3. Refer to page 6 for instructions on how to use the cam lock system.
5.4. Do not over tighten bolts.
11
front edge
(H2) x 8
cam bolt
(H3) x 8
cam
Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
Screw-In cam bolts must be screwed down ush.
Refer to page 6 for instructions on how to use the cam lock system.

step 6: attach back panel
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 20
short pan head
screw
6.1. Make sure the screws go through the pre-drilled holes properly.
6.2. Do not over tighten screws.
12
hole for anti-tip

step 7: install shelf
(H8) x 4
shelf support
7.1. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
7.2. Angle shelf to t between the rails and set on top of shelf supports.
13

step 8: assemble drawer starting with drawer sides / nish assembly with back panel
(H1) x 6
wooden dowel
(H2) x 5
cam bolt
(H3) x 5
cam
(H7) x 5
at head screw
8.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
8.2. Screw-In cam bolts must be screwed down ush.
8.3. Refer to page 6 for instructions on how to use the cam lock system.
8.4. Align screws with pre-drilled holes.
8.5. Do not over tighten screws.
14

step 9: attach knobs and install drawer
(H5) x 2
knob
(H6) x 2
knob bolt
9.1. Do not over tighten bolts.
15

step 10: install anti-tip kit
(H10) x 1
long pan head
screw
(H12) x 1
wall strap
(H9) x 1
wall anchor
(H11) x 1
wall screw
(H13) x 2
washer
Position against wall
Mark position of strap hole on wall
Drill 1/4” hole
Tap in wall anchor
Fasten anti-tip strap with wall screw
provided
16
(H11)
(H12)
(H10)
(H13)
(H9)
(H13)

WARNING
Children have died from furniture tipover.
To reduce the risk
of furniture tipover:
• ALWAYS install tipover restraint provided.
• NEVER put a
TV on this product.
• NEVER allow children to stand, climb or
hang
on drawers, doors, or shelves.
• Place heaviest items
in the lowest drawers.
• NEVER open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
This is a permanent label.
Do notremove!
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
17
40 lbs.
15 lbs.
30 lbs.
30 lbs.
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.