Target Halsted FRS80921 User manual

Halsted
Left Armchair
style # FRS80921
dpci # 009000787
>>assembly instructions

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
This Chair is not intended for use during any kind of inclement weather and the manufacturer is not,
and can not be, held responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Chair not being stored properly when not in use, is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Chair needs to be stored in a dry, sheltered place to
prolong the life and to avoid damage to the Chair.
2
IMPORTANT WARNING:
Unpack the box on a clean, soft, level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

WARRANTY:
This Chair comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your chair, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2019
before you begin
1. Check for damage or missing parts. Call to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
855-MYTGTHOME (855-698-4846)

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-10
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part D)×2
M6*25 mm screw with washer
(Part E)×1
(Part H)×1
allen wrench
M6*40mm screw with washer
(Part F)×2
M6*50mm screw with washer
(Part G)×2
M6*25 mm screw

ITEM DESCRIPTION QUANTITY
1
1
1
A
B
C
6
back frame
chair feet
seat frame

7
step 01:
Do not completely tighten screws until all screws are started.
1. Attach the seat frame (B) to the back frame (A) by lining up screw holes
on the seat frame (B) with corresponding screw holes on the back frame (A).
m part, tightenottobehtno
) and M6*40mm screw with washer (E)D(rehsaww withercsmm52*6MhtiweruceS.3
using allen wrench (H).
2. Secure with M6*50mm screw with washer (F) on the upper part.
tighten using allen wrench (H).
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. 2. 3.
(Part D)×2
M6*25 mm screw with washer
(Part E)×1
(Part H)×1
allen wrench
M6*40mm screw with washer
(Part F)×2
M6*50mm screw with washer
(Part G)×2
M6*25 mm screw

step 02:
8
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
Do not completely tighten screws until all screws are started.
1. Attach the seat frame (B) to the back frame (A) by lining up screw holes
on the seat frame (B) with corresponding screw holes on the back frame (A).
)D(rehsaww withercsmm25*6MhtiweruceS.2 , tighten using allen wrench (H).
(Part D)×2
M6*25 mm screw with washer
(Part E)×1
(Part H)×1
allen wrench
M6*40mm screw with washer
(Part F)×2
M6*50mm screw with washer
(Part G)×2
M6*25 mm screw

step 03:
9
Do not completely tighten screws until all screws are started.
1. Attach the chair feet (C) to the seat frame (B) and back frame (A) by lining up
screw holes on the chair feet (C) with corresponding screw holes on the seat frame
(B) and the back frame (A).
2. Secure with M6*25mm screw (G), tighten using allen wrench (H).
(Part D)×2
M6*25 mm screw with washer
(Part E)×1
(Part H)×1
allen wrench
M6*40mm screw with washer
(Part F)×2
M6*50mm screw with washer
(Part G)×2
M6*25 mm screw

step 04:
10
2. Return chair to upright position.
3. Put the cushion on the chair, tighten using the horn button
that sewed on the cushion.
1. Tighted all the screws.
You are now ready to enjoy your new chair.