Target Warwick FKWWCB2DBR User manual

>>
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
warwick
2 door accent cabinet
assembly instructions
style # FKWWCB2DBR (fawn brown)
dpci # 249-16-8735
tcin # 52166593
style # FKWWCB2DWH (white)
dpci # 249-17-3052
tcin # 54187460

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
assembly 6-12
how to adjust the door hinges 14
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 12
wooden dowel
(H2) x 8
bolt
(H3) x 8
lock washer
(H4) x 19
pan head screw
(H5) x 4
pull bolt
(H6) x 2
pull
(H7) x 4
shelf support
(H8) x 2
large at head screw
(H9) x 1
allen wrench
(H10) x 4
hinge
(H11) x 16
small at head screw
(H12) x 1
wall anchor
(H13) x 1
wall screw
(H14) x 1
small truss head screw
(H15) x 1
wall strap
(H16) x 10
washer

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
D bottom panel 1
E bottom rail 1
F back panel 1
G shelf 1
H door 2

step 1: attach top panel, bottom panel, and bottom rail to side panels
(H1) x 12
wooden dowel
(H2) x 8
bolt
(H3) x 8
lock washer
(H16) x 8
washer
(H9) x 1
allen key
1.1. Carefully tap small wooden dowels into place in top panel, bottom panel, and bottom rail. Leave 1/2” of the dowels sticking out.
1.2. Align bolts with pre-drilled holes to attach top panel to side panels. Do not over tighten bolts.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
6
notched edge

7
step 2: secure bottom rail
(H8) x 2
large at
head screw
2.1. Align large at head screws with pre-drilled holes to attach bottom rail to side panels. Do not over tighten screws..

step 3: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 19
pan head screw
3.1. Make sure the pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
8
hole for anti-tip

9
step 4: install adjustable shelf
(H7) x 4
shelf support
4.1. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
4.2. Angle shelf to t between the rails and set on top of shelf supports.

10
step 5: attach doors to cabinet
(H11) x 16
small at
head screw
(H10) x 4
hinge
(H5) x 4
pull bolt
(H6) x 2
pull
5.1. Align small at head screws with pre-drilled holes to attach hinge to door. Do not over tighten screws.
5.2. Align small at head screws with pre-drilled holes to attach door to cabinet. Do not over tighten screws.
5.3. Align pull bolt with pre-drilled holes to attach pull to door. Do not over tighten bolts.