TECO L510 User manual

Page 1 of 7 12/06/13
TECO L510 Inverter
Quick Start Guide
1) Ensure that the Inverter & the motor have the correct
KW power and voltage ratings.
Motor full load amps must not exceed the Inverter rating.
2) Ensure that the supply & Motor cables are connected
Correctly prior to power up.
3) For single phase supply, use L1& L3 ( N) on units which
have 3 supply terminals.
On units with two supply terminals L1&L2, connect live to L1
and Neutral to L2.
4) Connect motor cable to terminals T1,T2 &T3.
(Swap two leads If motor runs in reveres direction).
5) Connect supply Earth and the motor Earth to the drive Earth
terminal.
Note:-
I ) For detailed installation
and wiring refer to the
Instruction manual.
This guide is to assist you in installing and running the inverter and verify that it is
functioning correctly for it’s main and basic features.
For detailed information and if there are any doubts please refer to the instruction manual.
Step 1 Supply & Motor connection

Page 2 of 7 12/06/13
Apply power to the drive, the display will briefly show the supply voltage
220V followed by flashing.
This is the default ( factory set) frequency.
If the unit has been used previously then it will show the last frequency
programmed.
Step 2 Apply power to the drive
05.0
Step 3 Test run from keypad
Press RUN KEY to run.
The frequency will ram up to 5.0 Hz or the user pre-set frequency and
according to the default acceleration ramp time.
Press STOP/RESET key to stop.
The frequency will ramp down to zero according to the default decel ramp
time.
Step 4 To alter frequency from keypad. (Default setting).
Use the Arrow keys and </ Enter
To alter the digits to the required frequency.
eg. 50.0 HZ then use RUN and STOP keys to start/ stop.

Page 3 of 7 12/06/13
Remote speed reference and Remote run
1) Ensure that you have carried out installation & wiring requirements as
per step1 quick start guide on previous page before you proceed.
2) For analogue signal type 0-10V dc. Use the terminal AVI.
For analogue input type 4-20 mA.dc. Use the terminal ACI.
.Connect remote potentiometer OR remote 0-10 vdc signal as required.
to terminals AVI.
Terminal 10Vdc is the supply provided for use with the potentiometer.
Terminal AVI for potentiometer wiper connection.
Terminal AGND is 0Vdc.
3) Connect remote start switch if required according to diagram in the
instruction manual.
Use terminals +12Vdc & S1 (Forward run).
Use terminals +12Vdc & S2 (Reverse run)
+12Vdc is the common terminal for PNP type inverters.
COM (0Vdc) terminal is common for the NPN type inverters.
Step 1 Remote mode wiring. Speed reference and Run signals.
Step 2 Remote mode Run
1) Power up.
Display will read the frequency from one of the following according to the
Connection made to AVI terminal. Set parameter 00-05 =00-02
a) Remote external potentiometer
b) Remote 0-10VDC analog signal.
Step 3 Check/ verify and alter parameters
Check / verify and alter parameters for remote start & remote frequency
as necessary before you proceed. Parameters 00-02 & 00=05
See quick start parameter list & How to alter parameters.

Page 4 of 7 12/06/13
How to alter parameters
Step 4 RUN using remote speed reference.(Potentiometer,0-10vdc or 4-
20ma
)
1) To run. Activate the remote run switch connected to terminals
S1 ( FWD) or S2 ( REV) as required,. Parameter 00-02=00-01
The frequency will ram up to the frequency set on
the pot ( parameter 00-05 = 00-01 ) or
analog signal (0-10v dc /4-20ma) and according to the set
acceleration ramp time.
How to alter parameters using the keypad
1) To alter parameters:- Press the MODE key,
until the first parameter 00-00 is displayed.
2) Then use the arrow keys to select the parameter required then
Press < / ENTER key to read the preset value.
3) Use the and < / ENTER keys to alter the setting of the
parameters as per basic quick start parameter list.
Note:- For full parameter list refer to the instruction manual.
4) To save each parameter change, press < / ENTER key then
the word END will be displayed.
5) Use key to select the next parameter to alter and
follow steps 2 to 4 until all changes are complete.
6) Pressing the MODE key repeatedly will alternate the display
between the preset frequency ( flashing display) and the last parameter
accessed or other selectable displays 0 to 7 when selected by parameter
12-00 according to the table below.
【0】:Disable display 【1】:output Current
【2】:output Voltage 【3】:DC voltage
【4】:Temperature 【5】:PID feedback
【
6
】
:AVI
【
7
】
:ACI

Page 5 of 7 12/06/13
Basic Quick Start Parameter List
Parameter Default Range Note
00-14 10.0 0.1~3600.0 Acceleration time in Secs
00-15 10.0 0.1~3600.0 Deceleration time in Secs
00-04 000 0-2 0: Forward/Stop-Reverse/Stop
1: Run/Stop-Reverse/Forward
2: 3-Wire Control Mode-Run/Stop
00-12 50/60Hz
0.01~650.00
Max frequency limit.
00-13 0.0 0.00~649.00
Min frequency limit
00-02 00-00 0-2 Start mode:-
Keypad = 00-00
Remote = 00=01
Communication = 00-02
00=05 00-00 0-6
00-00 = keypad
00-01= Potentiometer on keypad
00-02= External AVI analogue signal
00-03= External ACI analogue signal
00-04 =External up/down frequency control
00-05= control by Communication method
00-06=PID output
07-09 000 0-1 Stop method:- 00-00 = Decel to stop
00-01= Coast to stop
02-01 **A **A Motor overload protection
13-08 000 Set to factory setting.
1150 = 50 HZ system.
1160 = 60HZ system
Note:- For Full Parameter List see the Instruction manual

Page 6 of 7 12/06/13
Interconnection Diagram.
Single phase (PNP):
AC Power
source
L1(L)
S2
S3
S4
+
T1
T2
T3
S5
+12V
S1
-
Frequency
reference or PID
Multi-function input
Fuse
Inverter
output
Ground
E
Main
Switch
Power
input
RS485
1:A+
2:B-
3:A+
4: RX
D0
5: TX
D0
6:B-
7:VCC
8:A
GN
D
Pin1 to Pin 8
AO
AGND
+
-
L3(N)
RC
RA
Multi-function output
0~10V / 4~20mA
CON2
10V
AVI (0~10V)
ACI (0~20mA)
AGND
AO
Relay output
250VAC/1A
(30VDC/1A)
M
Model:
200V : L510-2P2-H1F-P / L510-2P5-H1F-P / L510-201-H1F-P
L510-202-H1F-P / L510-203-H1F-P
Note:- Supply voltage must not be connected to Inverter output terminals
T1,T2 ,T3. This will damage the inverter.
RB

Page 7 of 7 12/06/13
Three phase (NPN):
AC Power
source
L1(L)
S2
S3
S4
+
T1
T2
T3
S5
COM
S1
-
Frequency
reference or PID
Multi-function input
Fuse
Inverter
output
Ground
E
Main
Switch
Power
input
RS485
1:A+
2:B-
3:A+
4: RX
D0
5: TX
D0
6:B-
7:VCC
8:A
GN
D
Pin1 to Pin 8
AO
AGND
+
-
RC
RA
Multi-function output
0~10V / 4~20mA
CON2
10V
AVI (0~10V)
ACI (0~20mA)
AGND
AO
Relay output
250VAC/1A
(30VDC/1A)
M
L3(N)
L2
Model:
200V : L510-2P2-H3-N / L510-2P5-H3-N / L510-201-H3-N
L510-202-H3-N / L510-203-H3-N
RB