Teknion UWSPBS Operating and maintenance instructions

Standard District Storage to District Panel Bracket (UWSPBS)
Parallel Mounting
(p. 2 - 4)
For Customer Support please contact
[email protected]
PARALLEL
(UWSPBSPN R/L - 3/8" gap) OR
(UWSPBSPW R/L - 1" gap)
A - Top Bracket (RH shown)
(A15-8933 R/L)x1 with 3/8" gap, OR
(A15-8796 R/L)x1 with 1" gap
B- Bottom Bracket (RH shown)
(A15-8934 R/L)x1 with 3/8" gap , OR
(A15-8794 R/L)x1 with 1" gap
PERPENDICULAR BACK
(UWSPBSBN R/L)
C - Top Bracket (RH shown)
(A15-8799 R/L)x1
D- Bottom Bracket (RH shown)
(A15-8935 R/L)x1
PERPENDICULAR FRONT
(UWSPBSFN R/L - 3/8" gap) OR
(UWSPBSFW R/L - 1" gap)
E - Top Bracket (RH shown)
(A15-8797 R/L)x1 with 3/8" gap, OR
(A15-8798 R/L)x1 with 1" gap
F- Bottom Bracket (RH shown)
**same as Item B above
Top Bracket Hardware:
G - #10 x 7/8", Quad, Pan Washer Hd
Screw (E07-0077)x4
Bottom Bracket Hardware:
H- 5/16"-18 3/4" Hex Hd, Cad Plated
Bolt (E03-0125)x1
I - Bottom Anti-dislodgement Plate
**Parallel and Perpendicular Front Only
(A15-8795)x1
OR
OR
Perpendicular BACK
Mounting (p. 2, 3, 5)
Perpendicular FRONT
Mounting (p. 2, 3, 6)
A, G
B
C, G
DE, G
F
I
H
I
H
H
NOTE:
Included in this Guide - "Standard Storage to
Panel Attachment Options Chart", see p. 7-8.
HARDWARE included with each product:
district
Section:
Description: Page No:
Date:
Rev. No: 2
Nov 2015 1 of 8
DIS_703
Part and Product Identification

STEP 2: There are two ways of mounting cabinets to Top Brackets: (1) The top illustration
shows the Bracket can be inserted into the thin slot on the back of cabinet (2) For the
Perpendicular Front Mount, the Bracket wraps around the side wall of a cabinet.
STEP 1: There are two versions of Bottom Brackets. Their installed locations and hook
profiles are identical. To install, simply push and engage hooks of Bracket into the edge slots
that are covered by thin black tape on the Panel. The cut-outs on the horizontal flanges of the
Brackets are for fitting into the Levellers and Bolts (see STEP 5), located on the bottom of
cabinets.
Thin Black
Tape
Side View
Slot
Back View
9th Slot
from
bottom
~ 9 1
2"
Parallel or Perpendicular Front
Mounting
Perpendicular Back
Mounting
(RH shown, LH opposite)
(RH shown, LH opposite)
Cut-
outs
Cut-out
Parallel or Perpendicular Back
Mounting
Perpendicular Front
Mounting
Section:
Description: Page No:
Date:
BOTTOM BRACKETS - OVERVIEW TOP BRACKETS - OVERVIEW
DIS_703
2 of 8
Nov 2015
district

STEP 4: More than one set of Brackets may be required in Parallel Mount configuration.
Check Layout Plan and Instructions to ensure proper number and type of Brackets are used.
STEP 3: The Top and Bottom Brackets for different mounting options look very similar.
Study the furniture layout drawings carefully and ensure to pick up the proper Brackets for
installation. Pay particular attention to the 1" and 3/8" Gap requirements.
STEP 5: To prepare cabinet for mounting, screw the Hex Bolt into the proper insert on the
bottom of cabinet, leaving about 1/2" gap for future installation of Bottom Bracket and
Anti-dislodgement Plate.
RH shown
LH opposite
RH Brackets
LH Brackets
H
Parallel Mount
Perpendicular
Back Mount
Perpendicular
Front Mount
District
Panel
Cabinet Front
Cabinet Front
Cabinet Front
Bottom Views of Cabinets
and Distrcit Panels
Insert for
Hex Bolt
Leveler
Section:
Description: Page No:
Date:
ATTENTION
ATTENTION
TO DO FIRST
DIS_703
3 of 8
Nov 2015
district

STEP 6: (1) Follow STEPs 1 & 5 to install Bottom Bracket and Hex Bolt. (2) Bring
cabinet close to its installed position. (3) Engage hooks of Top Bracket into the edge slots on
Panel. (4) Slide cabinet towards the Panel until the Top Bracket is inserted into the back slot of
cabinet completely. At the same time, both the Leveler and the Bolt on bottom of cabinet
should fit inside the cut-out of Bottom Bracket.
STEP 7: Level and adjust cabinet position if necessary. Secure cabinet to Top Bracket with
wood screws.
STEP 8: Insert the Anti-Dislodgement Plate between the Bracket and the Bolt in the
orientation as shown. Tighten Hex Bolt to secure the assembly.
G
I
B
A
Section:
Description: Page No:
Date:
INSTALL BRACKETS AND POSITION CABINET SECURE TOP BRACKET
SECURE BOTTOM BRACKET
DIS_703
4 of 8
Nov 2015
district

STEP 6: (1) Follow STEPs 1 & 5 to install Bottom Bracket and Hex Bolt. (2) Bring
cabinet close to its installed location. (3) Insert the flat flange of Top Bracket into the back slot
of cabinet and at the same time, engage hooks of Top Bracket into the edge slots on Panel. (4)
At the bottom, both the Leveler and the Bolt should fit inside both of the cut-outs of Bottom
Bracket.
STEP 7: Level and adjust cabinet position if necessary. Secure cabinet to Top Bracket with
wood screws.
STEP 8: Tighten Hex Bolt to secure the assembly.
NOTE: Anti-Dislodgement Plate is not required for this configuration.
C
D
H
G
district
Section:
Description: Page No:
Date:
INSTALL BRACKETS AND POSITION CABINET SECURE TOP BRACKET
SECURE BOTTOM BARCKET
DIS_703
DIS_703

STEP 6: Follow STEPs 1 & 5 to install Bottom Bracket and Hex Bolt. Slide storage unit
towards Panel until the Leveler and the Bolt are fitted into the cut-out of the Bottom Bracket.
STEP 7: Posistion flange of Bracket inside the cabinet and engage hooks into the edge slots of
Panel.
STEP 8: Level and adjust cabinet position if necessary. Insert the Anti-Dislodgement Plate
between the Bracket and the Bolt in the orientation as shown. Tighten Hex Bolt to secure the
assembly.
STEP 9: Secure cabinet to Top Bracket with wood screws.
F
HE
I
G
district
Section:
Description: Page No:
Date:
CONNECT STORAGE UNIT TO BOTTOM BRACKET ATTACH TOP BRACKET
SECURE BOTTOM BRACKET SECURE TOP BRACKET
DIS_703

Parallel
UNSPBSP
Perpendicular
Front UNSPBSF
Perpendicular
Back UNSPBSB
Standard Storage Units Parallel
UNSPBSP
Perpendicular
Front UNSPBSF
Perpendicular
Back UNSPBSB
Standard Storage Units
Section:
Description: Page No:
Date:
Rev. No: 2
Nov 2015 7 of 8
DIS_703
district

Parallel
UNSPBSP
Perpendicular
Front UNSPBSF
Perpendicular
Back UNSPBSB
Standard Storage Units NOTES
Section:
Description: Page No:Date:
Rev. No: 2
Nov 2015 8 of 8
DIS_703
district