Teknion complements LIVELLO Operating and maintenance instructions

Standard/Extended Range Electric Table (LVWR & LVCC)
& Freestanding/Intergrated (LVFD, LVHU & LVHT)
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 4
ADJUSTABLE WORKSTATION TABLE - ELECTRIC STANDARD, EXTENDED & CERDENZA RANGE
HEIGHT ADJUSTABLE TABLES (LIVELLO)
Aug 2017 1 of 6
COM_113
Installation Guides
complements
D1 - STD Range Leg
(N09-5577) x2
OR
EXT Range Leg
(N09-5713) x2
F - M10 x 1.5-25 Flat Head
Socket Screw (E01-0990) x4
I - M5X0.8-10 Flat Head
Cap Screw (E01-0989)x20
H - 1/4-20 x 5/8 Pan Quad
Machine Screw (E01-0992) x12
D3 - Foot Assembly
(A25-0493) x2
A1 - Workstation Table for
Display Switch
(As per order) x1
B1 - Display Switch
(N09-5600) x1
OR
Up/Down Switch
(N09-5796) x1
Straight and Curved
Worksurface for Height
Adjustable Corner
Tables (C05-9756) x1
LVCC
D2 - Channel
(A16-3943) x1
B2 - Bracket
(A16-3970)x1
B3 - #8 5/8" Screw
(E04-0091) x2
D5 - Leveller
(D06-4088) x4
D6 - Grommet
(P-2184) x1
C2 - 6 x 5/8 typ flat Screw
(E04-0090) x6
C1 - Cable Clamp
3/8 Nylon Blk
(B02-0558) x2
D4 - Strut
(A16-3957) x1
G1 - Control Box
(N09-5912) x1
G2 - #10 Pan Screw
2" length (E01-1009) x2
LVCC
NOTE: If
E-Chain is
specified, please
refer to
Installation
Guide
COM_102a for
instructions.
NOTE: Workstation
for Display Switch
shown as example.
G1
A
D4
D3
D1
D2
B1
E - 1000mm Motor Cable
(N09-5597) x2
OR
15" Long Motor Cable
(I04-0099) x02
B4 - 3/16" Wire Clamp
(B02-0598) x4

STEP 1: Install Legs to Channel and Feet to Legs. Fasten with screws provided.
Section:
Description: Page No:
Date:
INSTALL LEG TO CHANNEL
Aug 2017 2 of 6
COM_113
ADJUSTABLE WORKSTATION TABLE - STANDARD & EXTENDED RANGE
HEIGHT ADJUSTABLE TABLES (LIVELLO)
Installation Guides
complements
D5
D3
D1
D2
I
I
F

STEP 2: Attach Folded Struts to Legs.
Section:
Description: Page No:
Date:
INSTALL STRUTS TO LEGS
Aug 2017 3 of 6
COM_113
ADJUSTABLE WORKSTATION TABLE - STANDARD & EXTENDED RANGE
HEIGHT ADJUSTABLE TABLES (LIVELLO)
Installation Guides
complements
D4
I
I
D4

STEP 3: Place Control Boxes inside of Top Channels & Connect Motor Cables, Switch and Power Cord with Control Boxes. Power cord should go through the circular cut out on the Top
Channel and the Switch Cord should go through one of the lateral Top Channel Notches, as shown.
Section:
Description: Page No:
Date:
PLACE CONTROL BOXES INSIDE OF CHANNEL
Aug 2017 4 of 6
COM_113
ADJUSTABLE WORKSTATION TABLE - STANDARD & EXTENDED RANGE
HEIGHT ADJUSTABLE TABLES (LIVELLO)
Installation Guides
complements
E
G1
G1
Power Cord
(comes with Control Box)
E
B1 G1
Power Cord
(comes with Control Box)
NOTE: Do not force Motor Cable in to
the Control Box and Leg Connection.
Ensure pins inside Cable are straight
before inserting in to its port.

STEP 4: Install Switch with screws provided Align pilot holes from Worksurface to holes from Top Frame Strut.
Section:
Description: Page No:
Date:
INSTALL WORKSURFACES AND SWITCHES
Aug 2017 5 of 6
COM_113
ADJUSTABLE WORKSTATION TABLE - STANDARD & EXTENDED RANGE
HEIGHT ADJUSTABLE TABLES (LIVELLO)
Installation Guides
complements
B2
B1
D6
A
B3
H
D6
H
A
G1
G2
B1

STEP 5: Install Wire Clamp and Cable Clamp as suggested locations. Suggested Locations are shown above.
Section:
Description: Page No:
Date:
WIRE MANAGEMENT
Aug 2017 6 of 6
COM_113
ADJUSTABLE WORKSTATION TABLE - STANDARD & EXTENDED RANGE
HEIGHT ADJUSTABLE TABLES (LIVELLO)
C1 - Cable Clamp
B4 - 3/16" Wire Clamp
NOTE: Place Wire Management
as shown as diagram
NOTE: Underside View of Left
Hand Side shown as an example
Right Hand Side Left Hand Side
B4
C1
C2
Installation Guides
complements
To Initiate Table:
1. Adjust Table to the lowest
position.
2. Hold the DOWN ARROW
switch for 5 seconds until the table
adjusts and references itself.
* ENSURE TABLE MOTION IS
FREE AND UNOBSTRUCTED
IN BOTH UP AND DOWN
DIRECTIONS AND SURFACE
IS LEVEL.
C2