Teknion Savera Owner's manual

BACK TILT ADJUSTMENT BACK TILT ADJUSTMENT
BACK TILT ADJUSTMENT TENSION CONTROL
TENSION CONTROL TENSION CONTROL
SYNCHRO-TILT TASK:
he tension-adjustment wheel for
the synchro tilt ask chair is
located on the right. Leaning back,
decide if the resistance of the chair
is comfortable. If it is too stiff, turn
the tension adjustment knob
counter-clockwise. If the chair
back does not provide enough
resistance, turn the knob clockwise.
SYNCHRO-TILT XL:
he back tilt adjustment paddle is
located underneath the seat on the
left side. he back tilt adjustment
provides the ability to lock the back
into four different positions or
leave in free-flow.
o tilt the chair, sit in the chair and
unlock the paddle by pulling it up,
which will release the back to free
flow. o lock the desired position,
push the paddle down and the
back will lock.
SWIVEL-TILT TASK:
he swivel-tilt control lever is
located on the right. o tilt the
chair, sit in the chair and pull the
handle outward. Leaving the
handle in this position, the chair is
now in free flow mode and can
reach any position between upright
and fully reclining. o lock (upper
position only), bring chair to
upright position and push the
handle in.
SYNCHRO-TILT TASK:
he tilt control paddle on the left
locks the chair into four different
positions.
o tilt the chair, sit in the chair and
unlock the paddle by pushing it
down, which will release the back
to free flow. o lock in position,
pull the paddle up and the back
will lock in position.
SWIVEL-TILT TASK:
he tension-adjustment knob for
the swivel-tilt is located in the
middle directly under the seat.
urning the knob will increase or
decrease tension.
SYNCHRO-TILT XL:
he tension-adjustment wheel is
located underneath the seat on the
right side.
Leaning back with the back tilt
adjustment paddle in the up
position, determine if the resistance
of the chair is comfortable. If the
resistance is too stiff, turn the
tension adjustment wheel counter-
clockwise. If the chair back does
not provide enough resistance, turn
the wheel clockwise.
savera adjustment features & instructions

LUMBAR HEIGHT ADJUSTMENT SEAT HEIGHT ADJUSTMENT
SEAT DEPTH ADJUSTMENT ARM WIDTH ADJUSTMENT
ARM HEIGHT ADJUSTMENT ARM HEIGHT ADJUSTMENT
o adjust the arm width on Savera
Synchro- ilt, Swivel- ilt & Stool,
push the lever down and slide the
arm to the desired position. Push the
lever up to lock the arm in place.
Savera XL arms are fixed prior to
shipping in either standard or
generous position.
o adjust the seat depth, lift lever
up. Simultaneously lift your weight
from the seat while sliding the seat
forward or backward. Release the
lever to lock the seat in place. Seat
Depth Adjustment option is
available on Savera Synchro- ilt
ask and Swivel- ilt ask only.
he seat height-adjustment paddle
for Savera Synchro- ilt, Swivel- ilt
& XL is located underneath the seat
on the right side.
o raise the chair, lift the paddle up,
while lifting your weight from the
seat, until you reach the desired
height, then release. o lower the
chair, lift the paddle up, allowing
your weight to push the seat down
until you reach the desired height,
then release.
he seat height-adjustment paddle for
Savera Stool functions the same but
the paddle is located on the left side.
he lumbar height-adjustment
levers for Savera Synchro- ilt,
Swivel- ilt & Stool are found at
the sides of the chair. Pull levers up
or down to the desired position.
Savera XL does not have lumbar
height adjustment.
2D ARMS:
o adjust the arm height on Savera
Synchro- ilt, Swivel- ilt, Stool
and XL, lift the small button on
the outside of either arm to raise or
lower it to the desired position.
4D ARMS:
o adjust the arm height, press the
button located behind either arm
to raise or lower it to the desired
position. Release the button to lock
in place.
savera adjustment features & instructions

W rning
ipping or collapsing can result in serious injury. o prevent product failure and possible injury:
• Savera has been designed and tested for users weighing up to 275 lbs
• Savera XL has been designed and tested for users weighing up to 400 lbs
• Frequently inspect the chair for visible cracks and damages, tighten all screws, bolts, adjustable knobs and parts
• Do not use the chair if damaged or unstable – immediately remove it from service
• his chair is equipped with casters intended for use on carpeted surfaces. Use of these casters on hard surfaces could result in unexpected rolling
and tipping. Casters designed for use on hard surfaces are available. If in doubt, see your dealer for appropriate selection
• Do not stand on or use the chair as a step ladder
• Failure to follow these warnings could result in serious injury
4D ARM PIVOT ADJUSTMENT 4D ARM SLIDER ADJUSTMENT
STOOL SEAT HEIGHT STOOL FOOT RING HEIGHT
o raise or lower the stool’s foot
ring, turn the foot ring’s knob
counter clockwise to release the foot
ring and adjust the ring until you
reach the desired level. urn the
knob clockwise to lock in place.
o raise the chair, lift the paddle up
while lifting your weight from the
seat until you reach the desired level
and then release to lock in place. o
lower the chair, lift the paddle up
allowing your weight to push the
seat down to the desired level and
then release to lock in place.
o adjust the arm cap depth
position, grasp the arm cap and
firmly slide forward or backward to
the desired position.
o pivot the armrest, grasp the arm
cap, rotate inward or outward and
release at the desired position. Not
available on Savera XL.
savera adjustment features & instructions