Teknion District User manual

1" Gap
NOTES:
To attach storage to District Panel Wall, see
instructions in DIS_702 or DIS_703.
Allow a 1" gap between Panel and Worksurface.
A- Recatngular Worksurface (UNWR)
UNGEN without Infill
(L)
B4 - Worksurface Panel
Bracket
(A15-6949L/R) x1
B5 - Panel Connection
Bracket
(A15-6938L/R) x1
B6 - Bracket Retainer
(B02-0242) x2
B7 - 1
4-20 x 15mm
Murakoshi Screw
(E01-0635) x7
B8 - #10 x 7
8", Quad,
Pan Washer Hd,
Wood Screw
(E07-0077) x14
UNGEN with Infill
X06-0178
B2 - Horizontal Spanner
(A23-1676) x1
B3 - Gable Post
Sub-Assembly
- With Infill
(N09-2732L/R) x1
X06-0175
C3 - Worksurface Panel
Bracket
(A15-6949L/R) x1
C4 - Bracket Retainer
(B02-0242) x1
C5 - 1
4-20 x 15mm
Murakoshi Screw
(E01-0635) x1
C6 - #10 x 7
8", Quad,
Pan Washer Hd,
Wood Screw
(E07-0077) x14
UNCLN
D1- Mini Leg Weldment
(N09-2840) x1
D2 - #10 x 7
8", Quad, Pan Washer Head Screw
(E07-0077) x8
A
B / C
D
B1 - Gable Infill Panel
(C05-4829) x1
(L)
C1 - Open Gable Spanner
Sub-Assembly
(N09-1540) x1
C2 - Gable Post
Sub-Assembly
- No Infill
(N09-2333L/R) x1
(L)
(L)
(L)
Rectangular Worksurface (UNWR), End Gable (UNGEN),
Mini Leg (UNCLN)
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 2
WORKSURFACE WITH END GABLE AND MINI LEG
WORKSURFACES AND WORKSURFACE SUPPORTS
Jan 2019 1 of 3
DIS_505
district Installation Guides

B4
B6
B7
B3
B2
B1
B7
B7
B6
B5
STEP 1: Horizontal slots on Panel rails are covered by thin black tapes. To install Bracket,
push and engage hooks into the slots on Panel. Lock the Bracket in place by inserting the
Retainer as shown.
STEP 2: Push hooks of Connection Bracket into the horizontal slots on Panel. Lock Bracket
in position with a Retainer.
STEP 3: Insert and fasten the Gable Horizontal Spanner to the Gable Post.
Section:
Description: Page No:
Date:
INSTALL PANEL BRACKET INSERT CONNECTION BRACKET
ASSEMBLE END GABLE ASSEMBLE END GABLE
DIS_505
2 of 3
Jan 2019
WORKSURFACE WITH FIXED-HEIGHT END GABLE AND MINI-LEG
WORKSURFACES AND WORKSURFACE SUPPORTS
district Installation Guides
STEP 4: Fasten the Infill Panel.

Pilot Holes
To Use
Pilot Hole
To Use
B8
B7 Parallel
D2
D1
1" Gap
A
STEP 5: Fasten End Gable to Connection Bracket. STEP 6: On a clean surface, place Worksurface upside down. Use the pilot hole as shown as
location guide, attach Mini Leg to Worksurface with wood screws. Ensure the edges of the Leg
and Worksurface are in parallel.
STEP 7: Put Worksurface in place. Let the Mini Leg rest on the Credenza; it is fastened to the
Worksurface only.
Section:
Description: Page No:
Date:
INSTALL END GABLE ATTACH MINI LEG TO WORKSURFACE
PUT WORKSURFACE IN PLACE SECURE WORKSURFACE
DIS_505
3 of 3
Jan 2019
WORKSURFACE WITH FIXED-HEIGHT END GABLE AND MINI-LEG
WORKSURFACES AND WORKSURFACE SUPPORTS
district Installation Guides
STEP 8: Secure Worksurface to the End Gable with screws.